Matching Items (14)
Filtering by
- All Subjects: DC-to-DC converters
- All Subjects: Audio amplifiers--Design and construction.
- Genre: Masters Thesis
- Creators: Bakkaloglu, Bertan
- Creators: Chakraborty, Bijeta
Description
Modern Complex electronic system include multiple power domains and drastically varying power consumption patterns, requiring the use of multiple power conversion and regulation units. High frequency switching converters have been gaining prominence in the DC-DC converter market due to their high efficiency. Unfortunately, they are all subject to higher process variations jeopardizing stable operation of the power supply.
This research mainly focus on the technique to track changes in the dynamic loop characteristics of the DC-DC converters without disturbing the normal mode of operation using a white noise based excitation and correlation. White noise excitation is generated via pseudo random disturbance at reference and PWM input of the converter with the test signal being spread over a wide bandwidth, below the converter noise and ripple floor. Test signal analysis is achieved by correlating the pseudo-random input sequence with the output response and thereby accumulating the desired behavior over time and pulling it above the noise floor of the measurement set-up. An off-the shelf power converter, LM27402 is used as the DUT for the experimental verification. Experimental results show that the proposed technique can estimate converter's natural frequency and Q-factor within ±2.5% and ±0.7% error margin respectively, over changes in load inductance and capacitance.
This research mainly focus on the technique to track changes in the dynamic loop characteristics of the DC-DC converters without disturbing the normal mode of operation using a white noise based excitation and correlation. White noise excitation is generated via pseudo random disturbance at reference and PWM input of the converter with the test signal being spread over a wide bandwidth, below the converter noise and ripple floor. Test signal analysis is achieved by correlating the pseudo-random input sequence with the output response and thereby accumulating the desired behavior over time and pulling it above the noise floor of the measurement set-up. An off-the shelf power converter, LM27402 is used as the DUT for the experimental verification. Experimental results show that the proposed technique can estimate converter's natural frequency and Q-factor within ±2.5% and ±0.7% error margin respectively, over changes in load inductance and capacitance.
ContributorsBakliwal, Priyanka (Author) / Ozev, Sule (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2015
Description
In this thesis, a digital input class D audio amplifier system which has the ability
to reject the power supply noise and nonlinearly of the output stage is presented. The main digital class D feed-forward path is using the fully-digital sigma-delta PWM open loop topology. Feedback loop is used to suppress the power supply noise and harmonic distortions. The design is using global foundry 0.18um technology.
Based on simulation, the power supply rejection at 200Hz is about -49dB with
81dB dynamic range and -70dB THD+N. The full scale output power can reach as high as 27mW and still keep minimum -68dB THD+N. The system efficiency at full scale is about 82%.
to reject the power supply noise and nonlinearly of the output stage is presented. The main digital class D feed-forward path is using the fully-digital sigma-delta PWM open loop topology. Feedback loop is used to suppress the power supply noise and harmonic distortions. The design is using global foundry 0.18um technology.
Based on simulation, the power supply rejection at 200Hz is about -49dB with
81dB dynamic range and -70dB THD+N. The full scale output power can reach as high as 27mW and still keep minimum -68dB THD+N. The system efficiency at full scale is about 82%.
ContributorsBai, Jing (Author) / Bakkaloglu, Bertan (Thesis advisor) / Arizona State University (Publisher)
Created2015
Description
State of art modern System-On-Chip architectures often require very low noise supplies without overhead on high efficiencies. Low noise supplies are especially important in noise sensitive analog blocks such as high precision Analog-to-Digital Converters, Phase Locked Loops etc., and analog signal processing blocks. Switching regulators, while providing high efficiency power conversion suffer from inherent ripple on their output. A typical solution for high efficiency low noise supply is to cascade switching regulators with Low Dropout linear regulators (LDO) which generate inherently quiet supplies. The switching frequencies of switching regulators keep scaling to higher values in order to reduce the sizes of the passive inductor and capacitors at the output of switching regulators. This poses a challenge for existing solutions of switching regulators followed by LDO since the Power Supply Rejection (PSR) of LDOs are band-limited. In order to achieve high PSR over a wideband, the penalty would be to increase the quiescent power consumed to increase the bandwidth of the LDO and increase in solution area of the LDO. Hence, an alternative to the existing approach is required which improves the ripple cancellation at the output of switching regulator while overcoming the deficiencies of the LDO.
This research focuses on developing an innovative technique to cancel the ripple at the output of switching regulator which is scalable across a wide range of switching frequencies. The proposed technique consists of a primary ripple canceller and an auxiliary ripple canceller, both of which facilitate in the generation of a quiet supply and help to attenuate the ripple at the output of buck converter by over 22dB. These techniques can be applied to any DC-DC converter and are scalable across frequency, load current, output voltage as compared to LDO without significant overhead on efficiency or area. The proposed technique also presents a fully integrated solution without the need of additional off-chip components which, considering the push for full-integration of Power Management Integrated Circuits, is a big advantage over using LDOs.
This research focuses on developing an innovative technique to cancel the ripple at the output of switching regulator which is scalable across a wide range of switching frequencies. The proposed technique consists of a primary ripple canceller and an auxiliary ripple canceller, both of which facilitate in the generation of a quiet supply and help to attenuate the ripple at the output of buck converter by over 22dB. These techniques can be applied to any DC-DC converter and are scalable across frequency, load current, output voltage as compared to LDO without significant overhead on efficiency or area. The proposed technique also presents a fully integrated solution without the need of additional off-chip components which, considering the push for full-integration of Power Management Integrated Circuits, is a big advantage over using LDOs.
ContributorsJoshi, Kishan (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Seo, Jae-Sun (Committee member) / Arizona State University (Publisher)
Created2016
Description
Switching regulator has several advantages over linear regulator, but the drawback of switching regulator is ripple voltage on output. Previously people use LDO following a buck converter and multi-phase buck converter to reduce the output voltage ripple. However, these two solutions also have obvious drawbacks and limitations.
In this thesis, a novel mixed signal adaptive ripple cancellation technique is presented. The idea is to generate an artificial ripple current with the same amplitude as inductor current ripple but opposite phase that has high linearity tracking behavior. To generate the artificial triangular current, duty cycle information and inductor current ripple amplitude information are needed. By sensing switching node SW, the duty cycle information can be obtained; by using feedback the amplitude of the artificial ripple current can be regulated. The artificial ripple current cancels out the inductor current, and results in a very low ripple output current flowing to load. In top level simulation, 19.3dB ripple rejection can be achieved.
In this thesis, a novel mixed signal adaptive ripple cancellation technique is presented. The idea is to generate an artificial ripple current with the same amplitude as inductor current ripple but opposite phase that has high linearity tracking behavior. To generate the artificial triangular current, duty cycle information and inductor current ripple amplitude information are needed. By sensing switching node SW, the duty cycle information can be obtained; by using feedback the amplitude of the artificial ripple current can be regulated. The artificial ripple current cancels out the inductor current, and results in a very low ripple output current flowing to load. In top level simulation, 19.3dB ripple rejection can be achieved.
ContributorsYang, Zhe (Author) / Bakkaloglu, Bertan (Thesis advisor) / Seo, Jae-Sun (Committee member) / Lei, Qin (Committee member) / Arizona State University (Publisher)
Created2016