Matching Items (9)
Filtering by
- All Subjects: Electromagnetism
- Creators: Balanis, Constantine A
Description
Global Positioning System (GPS) is a navigation system widely used in civilian and military application, but its accuracy is highly impacted with consequential fading, and possible loss of communication due to multipath propagation and high power interferences. This dissertation proposes alternatives to improve the performance of the GPS receivers to obtain a system that can be reliable in critical situations. The basic performance of the GPS receiver consists of receiving the signal with an antenna array, delaying the signal at each antenna element, weighting the delayed replicas, and finally, combining the weighted replicas to estimate the desired signal. Based on these, three modifications are proposed to improve the performance of the system. The first proposed modification is the use of the Least Mean Squares (LMS) algorithm with two variations to decrease the convergence time of the classic LMS while achieving good system stability. The results obtained by the proposed LMS demonstrate that the algorithm can achieve the same stability as the classic LMS using a small step size, and its convergence rate is better than the classic LMS using a large step size. The second proposed modification is to replace the uniform distribution of the time delays (or taps) by an exponential distribution that decreases the bit-error rate (BER) of the system without impacting the computational efficiency of the uniform taps. The results show that, for a BER of 0.001, the system can operate with a 1 to 2 dB lower signal-to-noise ratio (SNR) when an exponential distribution is used rather than a uniform distribution. Finally, the third modification is implemented in the design of the antenna array. In this case, the gain of each microstrip element is enhanced by embedding ferrite rings in the substrate, creating a hybrid substrate. The ferrite rings generates constructive interference between the incident and reflected fields; consequently, the gain of a single microstrip element is enhanced by up to 4 dB. When hybrid substrates are used in microstrip element arrays, a significant enhancement in angle range is achieved for a given reflection coefficient compared to using a conventional substrate.
ContributorsRivera-Albino, Alix (Author) / Balanis, Constantine A (Thesis advisor) / Tepedelenlioğlu, Cihan (Committee member) / Kiaei, Sayfe (Committee member) / Aberle, James T (Committee member) / Arizona State University (Publisher)
Created2013
Description
The ability to monitor electrophysiological signals from the sentient brain is requisite to decipher its enormously complex workings and initiate remedial solutions for the vast amount of neurologically-based disorders. Despite immense advancements in creating a variety of instruments to record signals from the brain, the translation of such neurorecording instrumentation to real clinical domains places heavy demands on their safety and reliability, both of which are not entirely portrayed by presently existing implantable recording solutions. In an attempt to lower these barriers, alternative wireless radar backscattering techniques are proposed to render the technical burdens of the implant chip to entirely passive neurorecording processes that transpire in the absence of formal integrated power sources or powering schemes along with any active circuitry. These radar-like wireless backscattering mechanisms are used to conceive of fully passive neurorecording operations of an implantable microsystem. The fully passive device potentially manifests inherent advantages over current wireless implantable and wired recording systems: negligible heat dissipation to reduce risks of brain tissue damage and minimal circuitry for long term reliability as a chronic implant. Fully passive neurorecording operations are realized via intrinsic nonlinear mixing properties of the varactor diode. These mixing and recording operations are directly activated by wirelessly interrogating the fully passive device with a microwave carrier signal. This fundamental carrier signal, acquired by the implant antenna, mixes through the varactor diode along with the internal targeted neuropotential brain signals to produce higher frequency harmonics containing the targeted neuropotential signals. These harmonics are backscattered wirelessly to the external interrogator that retrieves and recovers the original neuropotential brain signal. The passive approach removes the need for internal power sources and may alleviate heat trauma and reliability issues that limit practical implementation of existing implantable neurorecorders.
ContributorsSchwerdt, Helen N (Author) / Chae, Junseok (Thesis advisor) / Miranda, Félix A. (Committee member) / Phillips, Stephen (Committee member) / Towe, Bruce C (Committee member) / Balanis, Constantine A (Committee member) / Frakes, David (Committee member) / Arizona State University (Publisher)
Created2014
Description
Horn antennas have been used for over a hundred years. They have a wide variety of uses where they are a basic and popular microwave antenna for many practical applications, such as feed elements for communication reflector dishes on satellite or point-to-point relay antennas. They are also widely utilized as gain standards for calibration and gain measurement of other antennas.
The gain and loss factor of conical horns are revisited in this dissertation based on
spherical and quadratic aperture phase distributions. The gain is compared with published classical data in an attempt to confirm their validity and accuracy and to determine whether they were derived based on spherical or quadratic aperture phase distributions. In this work, it is demonstrated that the gain of a conical horn antenna obtained by using a spherical phase distribution is in close agreement with published classical data. Moreover, more accurate expressions for the loss factor, to account for amplitude and phase tapers over the horn aperture, are derived. New formulas for the design of optimum gain conical horns, based on the more accurate spherical aperture phase distribution, are derived.
To better understand the impact of edge diffractions on aperture antenna performance, an extensive investigation of the edge diffractions impact is undertaken in this dissertation for commercial aperture antennas. The impact of finite uncoated and coated PEC ground plane edge diffractions on the amplitude patterns in the principal planes of circular apertures is intensively examined. Similarly, aperture edge diffractions of aperture antennas without ground planes are examined. Computational results obtained by the analytical model are compared with experimental and HFSS-simulated results for all cases studied. In addition, the impact of the ground plane size, coating thickness, and relative permittivity of the dielectric layer on the radiation amplitude in the back region has been examined.
This investigation indicates that the edge diffractions do impact the main forward lobe pattern, especially in the E plane. Their most significant contribution appears in far side and back lobes. This work demonstrates that the finite edge contributors must be considered to obtain more accurate amplitude patterns of aperture antennas.
The gain and loss factor of conical horns are revisited in this dissertation based on
spherical and quadratic aperture phase distributions. The gain is compared with published classical data in an attempt to confirm their validity and accuracy and to determine whether they were derived based on spherical or quadratic aperture phase distributions. In this work, it is demonstrated that the gain of a conical horn antenna obtained by using a spherical phase distribution is in close agreement with published classical data. Moreover, more accurate expressions for the loss factor, to account for amplitude and phase tapers over the horn aperture, are derived. New formulas for the design of optimum gain conical horns, based on the more accurate spherical aperture phase distribution, are derived.
To better understand the impact of edge diffractions on aperture antenna performance, an extensive investigation of the edge diffractions impact is undertaken in this dissertation for commercial aperture antennas. The impact of finite uncoated and coated PEC ground plane edge diffractions on the amplitude patterns in the principal planes of circular apertures is intensively examined. Similarly, aperture edge diffractions of aperture antennas without ground planes are examined. Computational results obtained by the analytical model are compared with experimental and HFSS-simulated results for all cases studied. In addition, the impact of the ground plane size, coating thickness, and relative permittivity of the dielectric layer on the radiation amplitude in the back region has been examined.
This investigation indicates that the edge diffractions do impact the main forward lobe pattern, especially in the E plane. Their most significant contribution appears in far side and back lobes. This work demonstrates that the finite edge contributors must be considered to obtain more accurate amplitude patterns of aperture antennas.
ContributorsAboserwal, Nafati Abdasallam (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T (Committee member) / Pan, George (Committee member) / Tepedelenlioğlu, Cihan (Committee member) / Arizona State University (Publisher)
Created2014
Description
Multiport antennas offer greater design flexibility than traditional one-port designs. An antenna array is a special case of a multiport antenna. If the antenna's inter-element spacing is electrically small, the antenna is capable of achieving superdirectivity. Superdirective antenna arrays are known to be narrow band and have low radiation resistance which leads to low radiation efficiency and high VSWR. However, by increasing the self-impedance of the antenna elements, the radiation resistance is increased but the bandwidth remains narrow. A design methodology is developed using the ability to superimpose electric fields and multi-objective optimization to design antenna feed networks. While the emphasis in this dissertation is on antenna arrays and superdirectivity, the design methodology is general and can be applied to other multiport antennas. The design methodology is used to design a multiport impedance-matching network and optimize both the input impedance and radiation pattern of a two-port superdirective antenna array. It is shown that the multiport impedance-matching network is capable of improving the input impedance of the antenna array while maintaining high directionality. The antenna design is critical for the methodology to improve the bandwidth and radiation characteristics of the array. To double the bandwidth of the two-port impedance matched superdirective antenna array, a three-port Yagi-Uda antenna design is demonstrated. The addition of the extra antenna element does not increase the footprint of the antenna array. The design methodology is then used to design a symmetrical antenna array capable of steering its main beam in two directions.
ContributorsArceo, Diana (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T., 1961- (Committee member) / Moeller, Karl (Committee member) / Palais, Joseph (Committee member) / Arizona State University (Publisher)
Created2012
Description
Scattering from random rough surface has been of interest for decades. Several
methods were proposed to solve this problem, and Kirchho approximation (KA)
and small perturbation method (SMP) are among the most popular. Both methods
provide accurate results on rst order scattering, and the range of validity is limited
and cross-polarization scattering coecient is zero for these two methods unless these
two methods are carried out for higher orders. Furthermore, it is complicated for
higher order formulation and multiple scattering and shadowing are neglected in these
classic methods.
Extension of these two methods has been made in order to x these problems.
However, it is usually complicated and problem specic. While small slope approximation
is one of the most widely used methods to bridge KA and SMP, it is not easy
to implement in a general form. Two scale model can be employed to solve scattering
problems for a tilted perturbation plane, the range of validity is limited.
A new model is proposed in this thesis to deal with cross-polarization scattering
phenomenon on perfect electric conducting random surfaces. Integral equation
is adopted in this model. While integral equation method is often combined with
numerical method to solve the scattering coecient, the proposed model solves the
integral equation iteratively by analytic approximation. We utilize some approximations
on the randomness of the surface, and obtain an explicit expression. It is shown
that this expression achieves agreement with SMP method in second order.
methods were proposed to solve this problem, and Kirchho approximation (KA)
and small perturbation method (SMP) are among the most popular. Both methods
provide accurate results on rst order scattering, and the range of validity is limited
and cross-polarization scattering coecient is zero for these two methods unless these
two methods are carried out for higher orders. Furthermore, it is complicated for
higher order formulation and multiple scattering and shadowing are neglected in these
classic methods.
Extension of these two methods has been made in order to x these problems.
However, it is usually complicated and problem specic. While small slope approximation
is one of the most widely used methods to bridge KA and SMP, it is not easy
to implement in a general form. Two scale model can be employed to solve scattering
problems for a tilted perturbation plane, the range of validity is limited.
A new model is proposed in this thesis to deal with cross-polarization scattering
phenomenon on perfect electric conducting random surfaces. Integral equation
is adopted in this model. While integral equation method is often combined with
numerical method to solve the scattering coecient, the proposed model solves the
integral equation iteratively by analytic approximation. We utilize some approximations
on the randomness of the surface, and obtain an explicit expression. It is shown
that this expression achieves agreement with SMP method in second order.
ContributorsCao, Jiahao (Author) / Pan, George (Thesis advisor) / Balanis, Constantine A (Committee member) / Cochran, Douglas (Committee member) / Arizona State University (Publisher)
Created2017
Description
In this dissertation a new wideband circular HIS is proposed. The circular periodicity made it possible to illuminate the surface with a cylindrical TEMz wave and; a novel technique is utilized to make it wideband. Two models are developed to analyze the
reflection characteristics of the proposed HIS.
The circularly symmetric high impedance surface is used as a ground plane for the design of a low-profile loop and spiral radiating elements. It is shown that a HIS with circular periodicity provides a wider operational bandwidth for curvilinear radiating elements such, such as loops and spirals, compared to canonical rectangular HISs.
It is also observed that, with the aid of a circular HIS ground plane the gain of a loop and a spiral increases compared to when a perfect magnetic conductor (PMC) or rectangular HIS is used as a ground plane. The circular HIS was fabricated and the loop and spiral elements were placed individually in close proximity to it.
Also, due to the growing demand for low-radar signature (RCS) antennas for advanced airborne vehicles, curved and flexible HIS ground planes, which meet both the aerodynamic and low RCS requirements, have recently become popular candidates within the antenna and microwave technology. This encouraged us, to propose a spherical HIS where a 2-D curvature is introduced to the previously designed flat HIS.
The major problem associated with spherical HIS is the impact of the curvature on its reflection properties. After characterization of the flat circular HIS, which is addressed in the first part of this dissertation, a spherical curvature is introduced to the flat circular HIS and its impact on the reflection properties was examined when it was illuminated with the same cylindrical TEMz wave. The same technique, as for the flat HIS ground plane, is utilized to make the spherical HIS wideband. A loop and spiral element were placed in the vicinity of the curved HIS and their performanceswere investigated. The HISs were also fabricated and measurements were conducted to verify the simulations. An excellent agreement was observed.
reflection characteristics of the proposed HIS.
The circularly symmetric high impedance surface is used as a ground plane for the design of a low-profile loop and spiral radiating elements. It is shown that a HIS with circular periodicity provides a wider operational bandwidth for curvilinear radiating elements such, such as loops and spirals, compared to canonical rectangular HISs.
It is also observed that, with the aid of a circular HIS ground plane the gain of a loop and a spiral increases compared to when a perfect magnetic conductor (PMC) or rectangular HIS is used as a ground plane. The circular HIS was fabricated and the loop and spiral elements were placed individually in close proximity to it.
Also, due to the growing demand for low-radar signature (RCS) antennas for advanced airborne vehicles, curved and flexible HIS ground planes, which meet both the aerodynamic and low RCS requirements, have recently become popular candidates within the antenna and microwave technology. This encouraged us, to propose a spherical HIS where a 2-D curvature is introduced to the previously designed flat HIS.
The major problem associated with spherical HIS is the impact of the curvature on its reflection properties. After characterization of the flat circular HIS, which is addressed in the first part of this dissertation, a spherical curvature is introduced to the flat circular HIS and its impact on the reflection properties was examined when it was illuminated with the same cylindrical TEMz wave. The same technique, as for the flat HIS ground plane, is utilized to make the spherical HIS wideband. A loop and spiral element were placed in the vicinity of the curved HIS and their performanceswere investigated. The HISs were also fabricated and measurements were conducted to verify the simulations. An excellent agreement was observed.
ContributorsAmiri, Mikal Askarian (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T (Committee member) / Bakkaloglu, Bertan (Committee member) / Trichopoulos, Georgios C (Committee member) / Arizona State University (Publisher)
Created2018
Description
The micromotions (e.g. vibration, rotation, etc.,) of a target induce time-varying frequency modulations on the reflected signal, called the micro-Doppler modulations. Micro-Doppler modulations are target specific and may contain information needed to detect and characterize the target. Thus, unlike conventional Doppler radars, Fourier transform cannot be used for the analysis of these time dependent frequency modulations. While Doppler radars can detect the presence of a target and deduce if it is approaching or receding from the radar location, they cannot identify the target. Meaning, for a Doppler radar, a small commercial aircraft and a fighter plane when gliding at the same velocity exhibit similar radar signature. However, using a micro-Doppler radar, the time dependent frequency variations caused by the vibrational and rotational micromotions of the two aircrafts can be captured and analyzed to discern between them. Similarly, micro-Doppler signature can be used to distinguish a multicopter from a bird, a quadcopter from a hexacopter or a octacopter, a bus from a car or a truck and even one person from another. In all these scenarios, joint time-frequency transforms must be employed for the analysis of micro-Doppler variations, in order to extract the targets’ features.
Due to ample bandwidth, THz radiation provides richer radar signals than the microwave systems. Thus, a Terahertz (THz) micro-Doppler radar is developed in this work for the detection and characterization of the micro-Doppler signatures of quadcopters. The radar is implemented as a continuous-wave (CW) radar in monostatic configuration and operates at a low-THz frequency of 270 GHz. A linear time-frequency transform, the short-time Fourier transform (STFT) is used for the analysis the micro-Doppler signature. The designed radar has been built and measurements are carried out using a quadcopter to detect the micro-Doppler modulations caused by the rotation of its propellers. The spectrograms are obtained for a quadcopter hovering in front of the radar and analysis methods are developed for characterizing the frequency variations caused by the rotational and vibrational micromotions of the quadcopter. The proposed method can be effective for distinguishing the quadcopters from other flying targets like birds which lack the rotational micromotions.
Due to ample bandwidth, THz radiation provides richer radar signals than the microwave systems. Thus, a Terahertz (THz) micro-Doppler radar is developed in this work for the detection and characterization of the micro-Doppler signatures of quadcopters. The radar is implemented as a continuous-wave (CW) radar in monostatic configuration and operates at a low-THz frequency of 270 GHz. A linear time-frequency transform, the short-time Fourier transform (STFT) is used for the analysis the micro-Doppler signature. The designed radar has been built and measurements are carried out using a quadcopter to detect the micro-Doppler modulations caused by the rotation of its propellers. The spectrograms are obtained for a quadcopter hovering in front of the radar and analysis methods are developed for characterizing the frequency variations caused by the rotational and vibrational micromotions of the quadcopter. The proposed method can be effective for distinguishing the quadcopters from other flying targets like birds which lack the rotational micromotions.
ContributorsKashyap, Bharath Gundappa (Author) / Trichopoulos, Georgios C (Thesis advisor) / Balanis, Constantine A (Committee member) / Aberle, James T (Committee member) / Arizona State University (Publisher)
Created2018
Description
Articially engineered two-dimensional materials, which are widely known as
metasurfaces, are employed as ground planes in various antenna applications. Due to
their nature to exhibit desirable electromagnetic behavior, they are also used to design
waveguiding structures, absorbers, frequency selective surfaces, angular-independent
surfaces, etc. Metasurfaces usually consist of electrically small conductive planar
patches arranged in a periodic array on a dielectric covered ground plane. Holographic
Articial Impedance Surfaces (HAISs) are one such metasurfaces that are capable of
forming a pencil beam in a desired direction, when excited with surface waves. HAISs
are inhomogeneous surfaces that are designed by modulating its surface impedance.
This surface impedance modulation creates a periodical discontinuity that enables a
part of the surface waves to leak out into the free space leading to far-eld radia-
tion. The surface impedance modulation is based on the holographic principle. This
dissertation is concentrated on designing HAISs with
Desired polarization for the pencil beam
Enhanced bandwidth
Frequency scanning
Conformity to curved surfaces
HAIS designs considered in this work include both one and two dimensional mod-
ulations. All the designs and analyses are supported by mathematical models and
HFSS simulations.
metasurfaces, are employed as ground planes in various antenna applications. Due to
their nature to exhibit desirable electromagnetic behavior, they are also used to design
waveguiding structures, absorbers, frequency selective surfaces, angular-independent
surfaces, etc. Metasurfaces usually consist of electrically small conductive planar
patches arranged in a periodic array on a dielectric covered ground plane. Holographic
Articial Impedance Surfaces (HAISs) are one such metasurfaces that are capable of
forming a pencil beam in a desired direction, when excited with surface waves. HAISs
are inhomogeneous surfaces that are designed by modulating its surface impedance.
This surface impedance modulation creates a periodical discontinuity that enables a
part of the surface waves to leak out into the free space leading to far-eld radia-
tion. The surface impedance modulation is based on the holographic principle. This
dissertation is concentrated on designing HAISs with
Desired polarization for the pencil beam
Enhanced bandwidth
Frequency scanning
Conformity to curved surfaces
HAIS designs considered in this work include both one and two dimensional mod-
ulations. All the designs and analyses are supported by mathematical models and
HFSS simulations.
ContributorsPandi, Sivaseetharaman (Author) / Balanis, Constantine A (Thesis advisor) / Palais, Joseph (Committee member) / Aberle, James T., 1961- (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2017
Description
Since the advent of High Impedance Surfaces (HISs) and metasurfaces, researchers
have proposed many low profile antenna configurations. HISs possess in-phase reflection, which reinforces the radiation, and enhances the directivity and matching bandwidth of radiating elements. Most of the proposed dipole and loop element designs that have used HISs as a ground plane, have attained a maximum directivity of 8 dBi. While HISs are more attractive ground planes for low profile antennas, these HISs result in a low directivity as compared to PEC ground planes. Various studies have shown that Perfect Electric Conductor (PEC) ground planes are capable of achieving higher directivity, at the expense of matching efficiency, when the spacing
between the radiating element and the PEC ground plane is less than 0.25 lambda. To establish an efficient ground plane for low profile applications, PEC (Perfect Electric Conductor) and PMC (Perfect Magnetic Conductor) ground planes are examined in the vicinity of electric and magnetic radiating elements. The limitation of the two ground planes, in terms of radiation efficiency and the impedance matching, are discussed. Far-field analytical formulations are derived and the results are compared with full-wave EM simulations performed using the High-Frequency Structure Simulator (HFSS). Based on PEC and PMC designs, two engineered ground planes are proposed.
The designed ground planes depend on two metasurface properties; namely in-phase reflection and excitation of surface waves. Two ground plane geometries are considered. The first one is designed for a circular loop radiating element, which utilizes a
circular HIS ring deployed on a circular ground plane. The integration of the loop element with the circular HIS ground plane enhances the maximum directivity up to 10.5 dB with a 13% fractional bandwidth. The second ground plane is designed for a square loop radiating element. Unlike the first design, rectangular HIS patches are utilized to control the excitation of surface waves in the principal planes. The final design operates from 3.8 to 5 GHz (27% fractional bandwidth) with a stable broadside maximum realized gain up to 11.9 dBi. To verify the proposed designs, a prototype was fabricated and measurements were conducted. A good agreement between simulations and measurements was observed. Furthermore, multiple square ring elements are embedded within the periodic patches to form a surface wave planar antenna array. Linear and circular polarizations are proposed and compared to a conventional square ring array. The implementation of periodic patches results in a better matching bandwidth and higher broadside gain compared to a conventional array.
have proposed many low profile antenna configurations. HISs possess in-phase reflection, which reinforces the radiation, and enhances the directivity and matching bandwidth of radiating elements. Most of the proposed dipole and loop element designs that have used HISs as a ground plane, have attained a maximum directivity of 8 dBi. While HISs are more attractive ground planes for low profile antennas, these HISs result in a low directivity as compared to PEC ground planes. Various studies have shown that Perfect Electric Conductor (PEC) ground planes are capable of achieving higher directivity, at the expense of matching efficiency, when the spacing
between the radiating element and the PEC ground plane is less than 0.25 lambda. To establish an efficient ground plane for low profile applications, PEC (Perfect Electric Conductor) and PMC (Perfect Magnetic Conductor) ground planes are examined in the vicinity of electric and magnetic radiating elements. The limitation of the two ground planes, in terms of radiation efficiency and the impedance matching, are discussed. Far-field analytical formulations are derived and the results are compared with full-wave EM simulations performed using the High-Frequency Structure Simulator (HFSS). Based on PEC and PMC designs, two engineered ground planes are proposed.
The designed ground planes depend on two metasurface properties; namely in-phase reflection and excitation of surface waves. Two ground plane geometries are considered. The first one is designed for a circular loop radiating element, which utilizes a
circular HIS ring deployed on a circular ground plane. The integration of the loop element with the circular HIS ground plane enhances the maximum directivity up to 10.5 dB with a 13% fractional bandwidth. The second ground plane is designed for a square loop radiating element. Unlike the first design, rectangular HIS patches are utilized to control the excitation of surface waves in the principal planes. The final design operates from 3.8 to 5 GHz (27% fractional bandwidth) with a stable broadside maximum realized gain up to 11.9 dBi. To verify the proposed designs, a prototype was fabricated and measurements were conducted. A good agreement between simulations and measurements was observed. Furthermore, multiple square ring elements are embedded within the periodic patches to form a surface wave planar antenna array. Linear and circular polarizations are proposed and compared to a conventional square ring array. The implementation of periodic patches results in a better matching bandwidth and higher broadside gain compared to a conventional array.
ContributorsAlharbi, Mohammed (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T (Committee member) / Palais, Joseph (Committee member) / Trichopoulos, Georgios C (Committee member) / Arizona State University (Publisher)
Created2020