ASU Electronic Theses and Dissertations
This collection includes most of the ASU Theses and Dissertations from 2011 to present. ASU Theses and Dissertations are available in downloadable PDF format; however, a small percentage of items are under embargo. Information about the dissertations/theses includes degree information, committee members, an abstract, supporting data or media.
In addition to the electronic theses found in the ASU Digital Repository, ASU Theses and Dissertations can be found in the ASU Library Catalog.
Dissertations and Theses granted by Arizona State University are archived and made available through a joint effort of the ASU Graduate College and the ASU Libraries. For more information or questions about this collection contact or visit the Digital Repository ETD Library Guide or contact the ASU Graduate College at gradformat@asu.edu.
Displaying 1 - 2 of 2
Filtering by
- All Subjects: power management
Description
A single solar cell provides close to 0.5 V output at its maximum power point, which is very
low for any electronic circuit to operate. To get rid of this problem, traditionally multiple
solar cells are connected in series to get higher voltage. The disadvantage of this approach
is the efficiency loss for partial shading or mismatch. Even as low as 6-7% of shading can
result in more than 90% power loss. Therefore, Maximum Power Point Tracking (MPPT)
at single solar cell level is the most efficient way to extract power from solar cell.
Power Management IC (MPIC) used to extract power from single solar cell, needs to
start at 0.3 V input. MPPT circuitry should be implemented with minimal power and area
overhead. To start the PMIC at 0.3 V, a switch capacitor charge pump is utilized as an
auxiliary start up circuit for generating a regulated 1.8 V auxiliary supply from 0.3 V input.
The auxiliary supply powers up a MPPT converter followed by a regulated converter. At
the start up both the converters operate at 100 kHz clock with 80% duty cycle and system
output voltage starts rising. When the system output crosses 2.7 V, the auxiliary start up
circuit is turned off and the supply voltage for both the converters is derived from the system
output itself. In steady-state condition the system output is regulated to 3.0 V.
A fully integrated analog MPPT technique is proposed to extract maximum power from
the solar cell. This technique does not require Analog to Digital Converter (ADC) and
Digital Signal Processor (DSP), thus reduces area and power overhead. The proposed
MPPT techniques includes a switch capacitor based power sensor which senses current of
boost converter without using any sense resistor. A complete system is designed which
starts from 0.3 V solar cell voltage and provides regulated 3.0 V system output.
low for any electronic circuit to operate. To get rid of this problem, traditionally multiple
solar cells are connected in series to get higher voltage. The disadvantage of this approach
is the efficiency loss for partial shading or mismatch. Even as low as 6-7% of shading can
result in more than 90% power loss. Therefore, Maximum Power Point Tracking (MPPT)
at single solar cell level is the most efficient way to extract power from solar cell.
Power Management IC (MPIC) used to extract power from single solar cell, needs to
start at 0.3 V input. MPPT circuitry should be implemented with minimal power and area
overhead. To start the PMIC at 0.3 V, a switch capacitor charge pump is utilized as an
auxiliary start up circuit for generating a regulated 1.8 V auxiliary supply from 0.3 V input.
The auxiliary supply powers up a MPPT converter followed by a regulated converter. At
the start up both the converters operate at 100 kHz clock with 80% duty cycle and system
output voltage starts rising. When the system output crosses 2.7 V, the auxiliary start up
circuit is turned off and the supply voltage for both the converters is derived from the system
output itself. In steady-state condition the system output is regulated to 3.0 V.
A fully integrated analog MPPT technique is proposed to extract maximum power from
the solar cell. This technique does not require Analog to Digital Converter (ADC) and
Digital Signal Processor (DSP), thus reduces area and power overhead. The proposed
MPPT techniques includes a switch capacitor based power sensor which senses current of
boost converter without using any sense resistor. A complete system is designed which
starts from 0.3 V solar cell voltage and provides regulated 3.0 V system output.
ContributorsSingh, Shrikant (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2015
Description
High-efficiency DC-DC converters make up one of the important blocks of state-of-the-art power supplies. The trend toward high level of transistor integration has caused load current demands to grow significantly. Supplying high output current and minimizing output current ripple has been a driving force behind the evolution of Multi-phase topologies. Ability to supply large output current with improved efficiency, reduction in the size of filter components, improved transient response make multi-phase topologies a preferred choice for low voltage-high current applications.
Current sensing capability inside a system is much sought after for applications which include Peak-current mode control, Current limiting, Overload protection. Current sensing is extremely important for current sharing in Multi-phase topologies. Existing approaches such as Series resistor, SenseFET, inductor DCR based current sensing are simple but their drawbacks such low efficiency, low accuracy, limited bandwidth demand a novel current sensing scheme.
This research presents a systematic design procedure of a 5V - 1.8V, 8A 4-Phase Buck regulator with a novel current sensing scheme based on replication of the inductor current. The proposed solution consists of detailed system modeling in PLECS which includes modification of the peak current mode model to accommodate the new current sensing element, derivation of power-stage and Plant transfer functions, Controller design. The proposed model has been verified through PLECS simulations and compared with a transistor-level implementation of the system. The time-domain parameters such as overshoot and settling-time simulated through transistor-level
implementation is in close agreement with the results obtained from the PLECS model.
Current sensing capability inside a system is much sought after for applications which include Peak-current mode control, Current limiting, Overload protection. Current sensing is extremely important for current sharing in Multi-phase topologies. Existing approaches such as Series resistor, SenseFET, inductor DCR based current sensing are simple but their drawbacks such low efficiency, low accuracy, limited bandwidth demand a novel current sensing scheme.
This research presents a systematic design procedure of a 5V - 1.8V, 8A 4-Phase Buck regulator with a novel current sensing scheme based on replication of the inductor current. The proposed solution consists of detailed system modeling in PLECS which includes modification of the peak current mode model to accommodate the new current sensing element, derivation of power-stage and Plant transfer functions, Controller design. The proposed model has been verified through PLECS simulations and compared with a transistor-level implementation of the system. The time-domain parameters such as overshoot and settling-time simulated through transistor-level
implementation is in close agreement with the results obtained from the PLECS model.
ContributorsBurli, Venkatesh (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017