Matching Items (96)
Description
Semiconductor nanowires are featured by their unique one-dimensional structure which makes them promising for small scale electronic and photonic device applications. Among them, III-V material nanowires are particularly outstanding due to their good electronic properties. In bulk, these materials reveal electron mobility much higher than conventional silicon based devices, for example at room temperature, InAs field effect transistor (FET) has electron mobility of 40,000 cm2/Vs more than 10 times of Si FET. This makes such materials promising for high speed nanowire FETs. With small bandgap, such as 0.354 eV for InAs and 1.52 eV for GaAs, it does not need high voltage to turn on such devices which leads to low power consumption devices. Another feature of direct bandgap allows their applications of optoelectronic devices such as avalanche photodiodes. However, there are challenges to face up. Due to their large surface to volume ratio, nanowire devices typically are strongly affected by the surface states. Although nanowires can be grown into single crystal structure, people observe crystal defects along the wires which can significantly affect the performance of devices. In this work, FETs made of two types of III-V nanowire, GaAs and InAs, are demonstrated. These nanowires are grown by catalyst-free MOCVD growth method. Vertically nanowires are transferred onto patterned substrates for coordinate calibration. Then electrodes are defined by e-beam lithography followed by deposition of contact metals. Prior to metal deposition, however, the substrates are dipped in ammonium hydroxide solution to remove native oxide layer formed on nanowire surface. Current vs. source-drain voltage with different gate bias are measured at room temperature. GaAs nanowire FETs show photo response while InAs nanowire FETs do not show that. Surface passivation is performed on GaAs FETs by using ammonium surfide solution. The best results on current increase is observed with around 20-30 minutes chemical treatment time. Gate response measurements are performed at room temperature, from which field effect mobility as high as 1490 cm2/Vs is extracted for InAs FETs. One major contributor for this is stacking faults defect existing along nanowires. For InAs FETs, thermal excitations observed from temperature dependent results which leads us to investigate potential barriers.
ContributorsLiang, Hanshuang (Author) / Yu, Hongbin (Thesis advisor) / Ferry, David (Committee member) / Tracy, Clarence (Committee member) / Arizona State University (Publisher)
Created2011
Description
ABSTRACT The purpose of this study was to determine the energy cost of four modes of resistance training (push-ups, pull-ups, curl-ups, lunges). Twelve well trained men aged 23.6 (SD=2.84) years were recruited to participate in the study. Each of the 12 men completed three trials of each of the four exercises on one visit to the laboratory lasting slightly over one hour (M=72 min, SD=5.9 min). The oxygen consumption of the men was monitored constantly throughout the trial and data was recorded every five seconds. Mean VO2 values were calculated for each exercise. The values for push-ups (M=11.57 ml/kg/min, SD=1.99), curl-ups (M=10.99 ml/kg/min, SD=1.48), pull-ups (M=10.87 ml/kg/min, SD=2.51), and lunges (M=14.18 ml/kg/min, SD=1.78) were converted to METs (Metabolic Equivalents). The MET values (3.31, 3.14, 3.11, and 4.05 respectively) all fall within the range of moderate intensity activity. The findings of this study show that a single set of any of the above exercises will qualify as a moderate intensity activity and can be used to meet recommendations on daily physical activity.
ContributorsVezina, Jesse (Author) / Ainsworth, Barbara (Thesis advisor) / Campbell, Kathryn (Committee member) / Woodruff, Larry (Committee member) / Arizona State University (Publisher)
Created2011
Description
This work focuses on a generalized assessment of source zone natural attenuation (SZNA) at chlorinated aliphatic hydrocarbon (CAH) impacted sites. Given the numbers of sites and technical challenges for cleanup there is a need for a SZNA method at CAH impacted sites. The method anticipates that decision makers will be interested in the following questions: 1-Is SZNA occurring and what processes contribute? 2-What are the current SZNA rates? 3-What are the longer-term implications? The approach is macroscopic and uses multiple lines-of-evidence. An in-depth application of the generalized non-site specific method over multiple site events, with sampling refinement approaches applied for improving SZNA estimates, at three CAH impacted sites is presented with a focus on discharge rates for four events over approximately three years (Site 1:2.9, 8.4, 4.9, 2.8kg/yr as PCE, Site 2:1.6, 2.2, 1.7, 1.1kg/y as PCE, Site 3:570, 590, 250, 240kg/y as TCE). When applying the generalized CAH-SZNA method, it is likely that different practitioners will not sample a site similarly, especially regarding sampling density on a groundwater transect. Calculation of SZNA rates is affected by contaminant spatial variability with reference to transect sampling intervals and density with variations in either resulting in different mass discharge estimates. The effects on discharge estimates from varied sampling densities and spacings were examined to develop heuristic sampling guidelines with practical site sampling densities; the guidelines aim to reduce the variability in discharge estimates due to different sampling approaches and to improve confidence in SZNA rates allowing decision-makers to place the rates in perspective and determine a course of action based on remedial goals. Finally bench scale testing was used to address longer term questions; specifically the nature and extent of source architecture. A rapid in-situ disturbance method was developed using a bench-scale apparatus. The approach allows for rapid identification of the presence of DNAPL using several common pilot scale technologies (ISCO, air-sparging, water-injection) and can identify relevant source architectural features (ganglia, pools, dissolved source). Understanding of source architecture and identification of DNAPL containing regions greatly enhances site conceptualization models, improving estimated time frames for SZNA, and possibly improving design of remedial systems.
ContributorsEkre, Ryan (Author) / Johnson, Paul Carr (Thesis advisor) / Rittmann, Bruce (Committee member) / Krajmalnik-Brown, Rosa (Committee member) / Arizona State University (Publisher)
Created2013
Description
Biofuel from microbial biomass is a viable alternative to current energy production practices that could mitigate greenhouse gas levels and reduce dependency on fossil fuels. Sustainable production of microbial biomass requires efficient utilization of nutrients like phosphorus (P). P is a limited resource which is vital for global food security. This paper seeks to understand the fate of P through biofuel production and proposes a proof-of-concept process to recover P from microbial biomass. The photosynthetic cyanobacterium Synechocystis sp. PCC 6803 is found to contain 1.4% P by dry weight. After the crude lipids are extracted for biofuel processing, 92% of the intercellular P is found within the residual biomass. Most intercellular P is associated with nucleic acids which remain within the cell after lipids are extracted. Phospholipids comprise a small percentage of cellular P. A wet chemical advanced oxidation process of adding 30% hydrogen peroxide followed by 10 min of microwave heating converts 92% of the total cellular P from organic-P and polyphosphate into orthophosphate. P was then isolated and concentrated from the complex digested matrix by use of resins. An anion exchange resin impregnated with iron nanoparticles demonstrates high affinity for P by sorbing 98% of the influent P through 20 bed volumes, but only was able to release 23% of it when regenerated. A strong base anion exchange resin sorbed 87% of the influent P through 20 bed volumes then released 50% of it upon regeneration. The overall P recovery process was able to recover 48% of the starting intercellular P into a pure and concentrated nutrient solution available for reuse. Further optimization of elution could improve P recovery, but this provides a proof-of-concept for converting residual biomass after lipid extraction to a beneficial P source.
ContributorsGifford, James McKay (Author) / Westerhoff, Paul (Thesis advisor) / Rittmann, Bruce (Committee member) / Vannela, Ravindhar (Committee member) / Arizona State University (Publisher)
Created2012
Improving cyanobacterial hydrogen production through bioprospecting of natural microbial communities
Description
Some cyanobacteria can generate hydrogen (H2) under certain physiological conditions and are considered potential agents for biohydrogen production. However, they also present low amounts of H2 production, a reaction reversal towards H2 consumption, and O2 sensitivity. Most attempts to improve H2 production have involved genetic or metabolic engineering approaches. I used a bio-prospecting approach instead to find novel strains that are naturally more apt for biohydrogen production. A set of 36, phylogenetically diverse strains isolated from terrestrial, freshwater and marine environments were probed for their potential to produce H2 from excess reductant. Two distinct patterns in H2 production were detected. Strains displaying Pattern 1, as previously known from Synechocystis sp. PCC 6803, produced H2 only temporarily, reverting to H2 consumption within a short time and after reaching only moderately high H2 concentrations. By contrast, Pattern 2 cyanobacteria, in the genera Lyngbya and Microcoleus, displayed high production rates, did not reverse the direction of the reaction and reached much higher steady-state H2 concentrations. L. aestuarii BL J, an isolate from marine intertidal mats, had the fastest production rates and reached the highest steady-state concentrations, 15-fold higher than that observed in Synechocystis sp. PCC 6803. Because all Pattern 2 strains originated in intertidal microbial mats that become anoxic in dark, it was hypothesized that their strong hydrogenogenic capacity may have evolved to aid in fermentation of the photosynthate. When forced to ferment, these cyanobacteria display similarly desirable characteristics of physiological H2 production. Again, L. aestuarii BL J had the fastest specific rates and attained the highest H2 concentrations during fermentation, which proceeded via a mixed-acid pathway to yield acetate, ethanol, lactate, H2, CO2 and pyruvate. The genome of L. aestuarii BL J was sequenced and bioinformatically compared to other cyanobacterial genomes to ascertain any potential genetic or structural basis for powerful H2 production. The association hcp exclusively in Pattern 2 strains suggests its possible role in increased H2 production. This study demonstrates the value of bioprospecting approaches to biotechnology, pointing to the strain L. aestuarii BL J as a source of useful genetic information or as a potential platform for biohydrogen production.
ContributorsKothari, Ankita (Author) / Garcia-Pichel, Ferran (Thesis advisor) / Vermaas, Willem F J (Committee member) / Rittmann, Bruce (Committee member) / Torres, Cesar (Committee member) / Arizona State University (Publisher)
Created2013
Description
As engineered nanomaterials (NMs) become used in industry and commerce their loading to sewage will increase. However, the fate of widely used NMs in wastewater treatment plants (WWTPs) remains poorly understood. In this research, sequencing batch reactors (SBRs) were operated with hydraulic (HRT) and sludge (SRT) retention times representative of full-scale biological WWTPs for several weeks. NM loadings at the higher range of expected environmental concentrations were selected. To achieve the pseudo-equilibrium state concentration of NMs in biomass, SBR experiments needed to operate for more than three times the SRT value, approximately 18 days. Under the conditions tested, NMs had negligible effects on ability of the wastewater bacteria to biodegrade organic material, as measured by chemical oxygen demand (COD). NM mass balance closure was achieved by measuring NMs in liquid effluent and waste biosolids. All NMs were well removed at the typical biomass concentration (1~2 gSS/L). However, carboxy-terminated polymer coated silver nanoparticles (fn-Ag) were removed less effectively (88% removal) than hydroxylated fullerenes (fullerols; >90% removal), nano TiO2 (>95% removal) or aqueous fullerenes (nC60; >95% removal). Although most NMs did not settle out of the feed solution without bacteria present, approximately 65% of the titanium dioxide was removed even in the absence of biomass simply due to self-aggregation and settling. Experiments conducted over 4 months with daily loadings of nC60 showed that nC60 removal from solution depends on the biomass concentration. Under conditions representative of most suspended growth biological WWTPs (e.g., activated sludge), most of the NMs will accumulate in biosolids rather than in liquid effluent discharged to surface waters. Significant fractions of fn-Ag were associated with colloidal material which suggests that efficient particle separation processes (sedimentation or filtration) could further improve removal of NM from effluent. As most NMs appear to accumulate in biosolids, future research should examine the fate of NMs during disposal of WWTP biosolids, which may occur through composting or anaerobic digestion and/or land application, incineration, or landfill disposal.
ContributorsWang, Yifei (Author) / Westerhoff, Paul (Thesis advisor) / Krajmalnik-Brown, Rosa (Committee member) / Rittmann, Bruce (Committee member) / Hristovski, Kiril (Committee member) / Arizona State University (Publisher)
Created2012
Description
ABSTRACT An Ensemble Monte Carlo (EMC) computer code has been developed to simulate, semi-classically, spin-dependent electron transport in quasi two-dimensional (2D) III-V semiconductors. The code accounts for both three-dimensional (3D) and quasi-2D transport, utilizing either 3D or 2D scattering mechanisms, as appropriate. Phonon, alloy, interface roughness, and impurity scattering mechanisms are included, accounting for the Pauli Exclusion Principle via a rejection algorithm. The 2D carrier states are calculated via a self-consistent 1D Schrödinger-3D-Poisson solution in which the charge distribution of the 2D carriers in the quantization direction is taken as the spatial distribution of the squared envelope functions within the Hartree approximation. The wavefunctions, subband energies, and 2D scattering rates are updated periodically by solving a series of 1D Schrödinger wave equations (SWE) over the real-space domain of the device at fixed time intervals. The electrostatic potential is updated by periodically solving the 3D Poisson equation. Spin-polarized transport is modeled via a spin density-matrix formalism that accounts for D'yakanov-Perel (DP) scattering. Also, the code allows for the easy inclusion of additional scattering mechanisms and structural modifications to devices. As an application of the simulator, the current voltage characteristics of an InGaAs/InAlAs HEMT are simulated, corresponding to nanoscale III-V HEMTs currently being fabricated by Intel Corporation. The comparative effects of various scattering parameters, material properties and structural attributes are investigated and compared with experiments where reasonable agreement is obtained. The spatial evolution of spin-polarized carriers in prototypical Spin Field Effect Transistor (SpinFET) devices is then simulated. Studies of the spin coherence times in quasi-2D structures is first investigated and compared to experimental results. It is found that the simulated spin coherence times for GaAs structures are in reasonable agreement with experiment. The SpinFET structure studied is a scaled-down version of the InGaAs/InAlAs HEMT discussed in this work, in which spin-polarized carriers are injected at the source, and the coherence length is studied as a function of gate voltage via the Rashba effect.
ContributorsTierney, Brian David (Author) / Goodnick, Stephen (Thesis advisor) / Ferry, David (Committee member) / Akis, Richard (Committee member) / Saraniti, Marco (Committee member) / Vasileska, Dragica (Committee member) / Arizona State University (Publisher)
Created2011
Description
Population growth and fresh water depletion challenge drinking water utilities. Surface water quality is impacted significantly by climate variability, human activities, and extreme events like natural disasters. Dissolved organic carbon (DOC) is an important water quality index and the precursor of disinfection by-products (DBPs) that varies with both hydrologic and anthropogenic factors. Granular activated carbon (GAC) is a best available technology for utilities to meet Stage 2 D/DBP rule compliance and to remove contaminants of emerging concern (CECs) (e.g., pharmaceutical, personal care products (PCPs), etc.). Utilities can operate GAC with more efficient and flexible strategies with the understanding of organic occurrence in source water and a model capable predicting DOC occurrence. In this dissertation, it was found that DOC loading significantly correlated with spring runoff and was intensified by dry-duration antecedent to first flush. Dynamic modeling based on reservoir management (e.g., pump-back operation) was established to simulate the DOC transport in the reservoir system. Additionally, summer water recreational activities were found to raise the level of PCPs, especially skin-applied products, in raw waters. GAC was examined in this dissertation for both carbonaceous and emerging nitrogenous DBP (N-DBP) precursors (i.e., dissolved organic nitrogen (DON)) removal. Based on the experimental findings, GAC preferentially removes UV254-absorbing material, and DOC is preferentially removed over DON which may be composed primarily of hydrophilic organic and results in the low affinity for adsorption by GAC. The presence of organic nitrogen can elevate the toxicity of DBPs by forming N-DBPs, and this could be a major drawback for facilities considering installation of a GAC adsorber owing to the poor removal efficiency of DON by GAC. A modeling approach was established for predicting DOC and DON breakthrough during GAC operation. However, installation of GAC adsorber is a burden for utilities with respect to operational and maintenance cost. It is common for utilities to regenerate saturated GAC in order to save the cost of purchasing fresh GAC. The traditional thermal regeneration technology for saturated GAC is an energy intensive process requiring high temperature of incineration. Additionally, small water treatment sites usually ship saturated GAC to specialized facilities for regeneration increasing the already significant carbon footprint of thermal regeneration. An innovative GAC regeneration technique was investigated in this dissertation for the feasibility as on-site water treatment process. Virgin GAC was first saturated by organic contaminant then regenerated in-situ by iron oxide nanocatalysts mixed with hydrogen peroxide. At least 70 % of adsorption capacity of GAC can be regenerated repeatedly for experiments using modeling compound (phenol) or natural organic matter (Suwannee River humic acid). The regeneration efficiency increases with increasing adsorbate concentration. Used-iron nanocatalysts can be recovered repeatedly without significant loss of catalytic ability. This in-situ regeneration technique provides cost and energy efficient solution for water utilities considering GAC installation. Overall, patterns were found for DOC and CEC variations in drinking water sources. Increasing concentrations of bulk (DOC and DON) and/or trace organics challenge GAC operation in utilities that have limited numbers of bed-volume treated before regeneration is required. In-situ regeneration using iron nanocatalysts and hydrogen peroxide provides utilities an alternative energy-efficient operation mode when considering installation of GAC adsorber.
ContributorsChiu, Chao-An (Author) / Westerhoff, Paul (Thesis advisor) / Rittmann, Bruce (Committee member) / Hristovski, Kiril (Committee member) / Arizona State University (Publisher)
Created2012
Description
Introduction: Several faith-based or faith-placed programs have focused on the physical dimension of wellness in efforts to improve health by increasing physical activity and improving diet behaviors. However, these programs were not designed to intervene on the mental dimension of wellness which is critical for stress reduction and health behavior change. Purpose: To evaluate the feasibility of a spirituality-based stress reduction and health behavior change intervention using the Spiritual Framework of Coping (SFC) model. Methods: This study was a quasi-experimental one group pretest posttest design. The study was a total of eight weeks conducted at a non-denominational Christian church. Participants were recruited from the church through announcements and flyers. The Optimal Health program met once a week for 1.5 hours with weekly phone calls during an additional four week follow-up period. Feasibility was assessed by the acceptability, demand, implementation, practicality, integration, and limited efficacy of the program. Analysis: Frequencies for demographics were assessed. Statistical analyses of feasibility objectives were assessed by frequencies and distribution of responses to feasibility evaluations. Limited efficacy of pretest and posttest measures were conducted using paired t-test (p <.05). Results: The Optimal Health Program was positively accepted by participants. The demand for the program was shown with average attendance of 78.7%. The program was successfully implemented as shown by meeting session objectives and 88% homework completion. The program was both practical for the intended participants and was successfully integrated within the existing environment. Limited efficacy changes within the program were mostly non-significant. Conclusion: This study tested the feasibility of implementing the Optimal Health program that specifically targeted the structural components of the Spiritual Framework of Coping Model identified to create meaning making and enhance well-being. This program may ultimately be used to help individuals improve and balance the spiritual, mental, and physical dimensions of wellness. However, length of study and limited efficacy measures will need to be reevaluated for program success.
ContributorsWalker, Jenelle R (Author) / Swan, Pamela (Thesis advisor) / Ainsworth, Barbara (Committee member) / Chisum, Jack (Committee member) / Fleury, Julie (Committee member) / Hooker, Steven (Committee member) / Arizona State University (Publisher)
Created2012
Description
The health enhancing effects of physical activity are well documented in the literature. However, women continue to report lower participation in exercise and physical activity (PA) compared to men. As women age an overall trend in decreased activity is observed. The primary place of activity reported in women is the home and one of the most commonly reported reasons for lack of physical activity is the lack of time. Few instruments have been developed that focus on the activity patterns of women. The Cross Cultural Physical Activity Study that this study was based on targeted women of color to assess the types of activity and constraints to activity experienced by African American and Native American women over 40 years old. This secondary data analysis focused on the psychometric properties of two scales used in the above study, The Physical Recreation Questionnaire (PRQ) and The Typical Week Physical Activity Survey (TWPAS). An exploratory factor analysis (EFA) was conducted on the 18 items from the Physical Recreation Questionnaire (PRQ) which focused on constraints to PA. The results of the EFA were a poor fit of a two factor model. The three factor model had a favorable fit in the EFA. Confirmatory factor analysis (CFA) was then conducted on the 18 items in the PRQ. Results of the CFA supported the presence of three latent variables: enjoyment of PA, constraints to PA, and negotiation of constraints to PA. The Typical Week Physical Activity Survey (TWPAS) is a 35 item measure of moderate PA that includes the activities most often reported by women. The purpose of the TWPAS was to capture habitual PA that might not be recorded in other PA questionnaires. The TWPAS was correlated with criterion measures of PA records, treadmill, accelerometer, and BMI. Although correlations were small, they were in the expected direction with the criterion measures. The evaluation of the instruments supported the presence of the construct of constraints to PA in the PRQ and the measurement of moderate intensity PA in the TWPAS.
ContributorsBishop, Jewel (Author) / Ainsworth, Barbara (Thesis advisor) / Komnenich, Pauline (Committee member) / Arizona State University (Publisher)
Created2012