Matching Items (108)
Filtering by
Description
As the prevalence and awareness of Autism Spectrum Disorder (ASD) increases, so does the variety of treatment options for primary symptoms (social interaction, communication, behavior) and secondary symptoms (anxiety, hyperactivity, GI problems, and insomnia). Various treatments, from Adderall to Citalopram to Flax Seed Oil promise relief for these symptoms. However, very little research has actually been done on some of these treatments. Additionally, the research that has been done fails to compare these treatments against one another in terms of symptom relief. The Autism Treatment Effectiveness Survey, written by Dr. James Adams, director of the Autism/Asperger's Research Program at ASU, and graduate student/program coordinator Devon Coleman, aims to fill this gap. The survey numerically rates medications based on benefit and adverse effects, in addition to naming specific symptoms that are impacted by the treatments. However, the survey itself was retrospective in nature and requires further evidence to support its claims. Therefore, the purpose of this research paper is to evaluate evidence related to the results of the survey. After the performing an extensive literature review of over 70 different treatments, it appears that the findings of the Autism Treatment Effectiveness Survey are generally well supported. There were a few minor discrepancies regarding the primary benefitted symptom, but there was not enough of a conflict to discount the information from the survey. As research is still ongoing, conclusions cannot yet be drawn for Nutritional Supplements, although the current data looks promising.
ContributorsAnderson, Amy Lynn (Author) / Adams, James (Thesis director) / Coleman, Devon (Committee member) / School of Nutrition and Health Promotion (Contributor) / W.P. Carey School of Business (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
Description
Vitamins and minerals are, by definition, essential substances that are necessary for good health, and needed by every cell and organ to function appropriately. A deficiency of any one vitamin or mineral can be very serious. Although a very healthy diet rich in vegetables, fruits, and protein can provide sufficient amounts of most vitamins and minerals, many people do not consume an adequate diet. During pregnancy, there is an increased need for vitamins and minerals to promote a healthy pregnancy and a healthy baby. Prenatal supplements are intended to supplement a normal diet to ensure that adequate amounts of vitamins and minerals are consumed. The US Food and Drug Administration (FDA) has established Recommended Dietary Allowances for total vitamin/mineral intake from food and supplements, but they have not established recommendations for prenatal supplements. Therefore, there is a very wide variation in the content and quality of prenatal supplements. Many prenatal supplements contain only minimal levels of some vitamins and few or no minerals, in order to minimize cost and the number of pills. This results in insufficient vitamin/mineral supplementation for many women, and hence does not fully protect them or their children from pregnancy complications and health problems. Therefore, we have created our own set of recommendations for prenatal supplements. Our recommendations are based primarily on four sources: 1) FDA's Recommended Daily Allowances for pregnant women, which are estimated to meet the needs of 97.5% of healthy pregnant women. 2) FDA's Tolerable Upper Limit, which is the maximum amount of vitamins/minerals that can be safely consumed without any risk of health problems. 3) National Health and Nutrition Examination Survey (NHANES), which evaluates the average intake of vitamins and minerals by women ages 20-40 years in the US 4) Research studies on vitamin/mineral deficiencies or vitamin/mineral supplementation during pregnancy, and the effect on pregnancy, birth, and child health problems. In summary, the RDA establishes minimum recommended levels of vitamin/mineral intake from all sources, and the NHANES establishes the average intake from foods. The difference is what needs to be consumed in a supplement, on average. However, since people vary greatly in the quality of their diet, and since most vitamins and minerals have a high Tolerable Upper Limit, we generally recommend more than the difference between the RDA and the average NHANES. Vitamins generally have a larger Tolerable Upper Limit than do minerals. So, we recommend that prenatal vitamin/mineral supplements contain 100% of the RDA for most vitamins, and about 50% of the RDA for most minerals. However, based on additional research studies described below, in some cases we vary our recommendations from those averages.
ContributorsSorenson, Jacob (Author) / Adams, James (Thesis director) / Pollard, Elena (Committee member) / College of Integrative Sciences and Arts (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
In injection molded plastic parts, knit lines occur where opposing streams of material fuse together while the mold cavity fills. When parts with knit lines experience external loading, the knit lines cause areas of mechanical weakness. This weakness is especially drastic in fiber-reinforced polymers due to an unfavorable orientation of fibers at the knit line. A possible way to reduce the impact of knit lines is to incorporate overflow tabs into the mold design. An overflow tab is a chamber attached to the mold cavity that provides an extra space for the end of material flow to occur. Research shows that overflow tabs improve the fiber orientation at the knit line, resulting in increased mechanical strength. The goal of this study is to utilize overflow tabs to optimize the knit line strength of nylon 6-6 that is 30% carbon fiber reinforced. In this project, an initial overflow tab is first designed. Then four modifications are made to the tab design, each altering a separate variable while holding the others constant. The design changes explored for the tab in this project include adding radii to the inlet, shifting the inlet location, increasing the inlet cross-sectional area by 50%, and increasing the tab chamber volume by 50%. Specimens were molded using the initial tab design and the modified tab designs. Testing for this experiment consists of three specimens of each type for three-point bending tests, and five specimens of each type for tensile tests. The material properties analyzed are the flexural modulus, flexural strength, tensile modulus, and tensile strength. From the testing, the tab with the 50% increased volume consistently yielded the highest results and showed large improvement from the initial tab design. However, the other three tab modifications either showed negative change or slight improvement from the initial tab design. Based on the results of this study, the overflow tab volume is the most beneficial design parameter to adjust.
ContributorsJones, Justin Michael (Author) / Adams, James (Thesis director) / Wamsley, Steven (Committee member) / Computer Science and Engineering Program (Contributor) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
The purpose of this honors project is to analyze the difference between different powder separation techniques, and their suitability for my capstone project – ‘Effect of Powder Reuse on DMLS (Direct Metal Laser Sintering) Product Integrity’. Due to the nature of my capstone project, my group needs to characterize foreign contaminants in IN 718 (Ni-based superalloy) powder with a mean diameter around 40um. In order to clearly analyze the contaminants and recycle useful IN 718 powders, powder separation is favorable since the filtered samples will be much easier to characterize rather than inspect all the powders at once under microscope. By conducting literature review, I found that powder separation is commonly used in Geology, and Chemistry department. To screen which combination of techniques could be the best for my project, I have consulted several research specialists, obtained adequate knowledge about powder separation. Accordingly, I will summarize the pros and cons of each method with regard the specific project that I am working on, and further explore the impacts of each method under economical, societal, and environmental considerations. Several powder separation techniques will be discussed in details in the following sections, including water elutriation, settling column, magnetic separation and centrifugation. In addition to these methods, sieving, water tabling and panning will be briefly introduced. After detailed comparison, I found that water elutriation is the most efficient way to purity IN718 powder for reuse purpose, and recovery rate is as high as 70%, which could result in a significant reduction in the manufacturing cost for Honeywell since currently Honeywell only use virgin powders to build parts, and 90% of the leftover powders are discarded.
ContributorsLuo, Zheyu (Author) / Adams, James (Thesis director) / Tasooji, Amaneh (Committee member) / Materials Science and Engineering Program (Contributor) / School of Sustainability (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
Honeywell is currently extending the reach of additive manufacturing (AM) in its product line and expects to produce as much as 40% of its inventory through AM in five years. Additive manufacturing itself is expected to grow into a $3.1 billion dollar industry in the next 5 to 10 years. Reusing IN 718 powder, a nickel-based super alloy metal powder, is an ideal option to reduce costs as well as reduce waste because it can be used with additive manufacturing, but the main obstacles are lack of procedure standardization and product quality assurances from this process. The goal of the capstone project, "Effect of Powder Reuse on DMLS (Direct Metal Laser Sintering) Product Integrity," is to create a powder characterization protocol in order to determine if the IN 718 powder can be reused and what effect the IN 718 reused powder has on the mechanical properties of the products Honeywell fabricates. To provide context and impact of this capstone project, this paper serves to identify the benefits of AM for Honeywell and the cost effectiveness of reusing the powder versus using virgin powder every time. It was found that Honeywell's investment in AM is due to the cost effectiveness of AM, versatility in product design, and to ensure Honeywell remains competitive in the future. In terms of reducing expenses, reusing powder enables costs to be approximately 45% less than using virgin powder. With these key pieces of information, the motivations for this capstone project are understood to a fuller and more profound degree.
ContributorsQuigley, Elizabeth (Co-author) / Luo, Zheyu (Co-author) / Murella, Anoosha (Co-author) / Lee, Wey Lyn (Co-author) / Adams, James (Thesis director) / Tasooji, Amaneh (Committee member) / Materials Science and Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
The vastly growing field of supercomputing is in dire need of a new measurement system to optimize JMRAM (Josephson junction magnetoresistive random access memory) devices. To effectively measure these devices, an ultra-low-noise, low cost cryogenic dipping probe with a dynamic voltage range is required. This dipping probe has been designed by ASU with <100 nVp-p noise, <10 nV offsets, 10 pV to 16 mV voltage range, and negligible thermoelectric drift. There is currently no other research group or company that can currently match both these low noise levels and wide voltage range. Two different dipping probes can be created with these specifications: one for high-use applications and one for low-use applications. The only difference between these probes is the outer shell; the high-use application probe has a shell made of G-10 fiberglass for a higher price, and the low-use application probe has a shell made of AISI 310 steel for a lower price. Both types of probes can be assembled in less than 8 hours for less than $2,500, requiring only soldering expertise. The low cost and short time to create these probes makes wide profit margins possible. The market for these cryogenic dipping probes is currently untapped, as most research groups and companies that use these probes build their own, which allows for rapid business growth. These potential consumers can be easily reached by marketing these probes at superconducting conferences. After several years of selling >50 probes, mass production can easily become possible by hiring several technicians, and still maintaining wide profit margins.
ContributorsHudson, Brooke Ashley (Author) / Adams, James (Thesis director) / Anwar, Shahriar (Committee member) / Materials Science and Engineering Program (Contributor) / W. P. Carey School of Business (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
How can we change what it means to be a human? Products can be used that will allow for near-instantaneous communication with one’s friends and family wherever they are: and the newest devices do not have to be even carried around, as they can be worn instead. Wearable electronics are quickly becoming very popular, with 232.0 million wearable devices sold in 2015. This report provides an overview of current and developing wearable devices, investigates the characteristics of the average buyer for these different types of devices. Finally, marketing strategies are suggested. This work was completed in conjunction with a capstone project with Intel, where three objectives were achieved: First, a universal strain tester that could strain samples cyclically in a manner similar to the body was designed. This equipment was especially designed to be flexible in the testing conditions it could be exposed to, so samples could be tested at elevated temperatures or even underwater. Next, dogbone shaped samples for the testing of Young’s Modulus and elongation to failure were produced, and the cut quality of laser, water-jet, and die-cutting was compared in order to select the most defect-free method for reliable testing. Polydimethylsiloxane (PDMS) is a fantastic candidate material for wearable electronics, however there is some discrepancies in the literature—such as from Eleni et. al—about the impact of ultraviolet radiation on the mechanical properties. By conducting accelerated aging tests simulating up to five years exposure to the sun, it was determined that ultraviolet-induced cross-linking of the polymer chains does occur, leading to severe embrittlement (strain to failure reduced from 3.27 to 0.06 in some cases, reduction to approximately 0.21 on average). As simulated tests of possible usage conditions required strains of at least 0.50-0.70, a variety of solutions were suggested to reduce this embrittlement. This project can lead to standardization of wearables electronics testing methods for more reliable predictions about the device behavior, whether that device is a simple pedometer or something that allows the visually impaired to “see”, such as Toyota’s Blaid.
ContributorsNiebroski, Alexander Wayne (Author) / Adams, James (Thesis director) / Anwar, Shahriar (Committee member) / Materials Science and Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
The work for this thesis was done in conjunction to that of my capstone project, which focused on understanding the effects of powder re-use on products built via Direct Metal Laser Sintering (DMLS), a specific additive manufacturing (AM) technique where powder particles are sintered together to form final parts. Honeywell Aerospace helped support this research by providing materials and mentorship; this work will play a key role in their decision to implement DMLS and other AM methods on a larger scale. Whereas the capstone focuses on the technical details of constructing characterization equipment, analyzing data, and formulating a concluding recommendation on whether the powder can be re-used, the thesis attempts to put this body of work in its greater context, surveying the economic and environmental effects of additive manufacturing technologies with a slant towards the aerospace industry. Shifts in the supply chain with aircraft parts and how this affects costs are explored, as well as how the quality and reliability of additively manufactured parts differs from their traditionally manufactured counterparts and the effects of this on related industries and purchasers.
ContributorsMurella, Anoosha Sainagaki (Author) / Adams, James (Thesis director) / Tasooji, Amaneh (Committee member) / Materials Science and Engineering Program (Contributor) / School of Molecular Sciences (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
Globally, about two-thirds of the population is latently infected with herpes simplex virus type 1 (HSV-1). HSV-1 is a large double stranded DNA virus with a genome size of ~150kbp. Small defective genomes, which minimally contain an HSV-1 origin of replication and packaging signal, arise naturally via recombination during viral DNA replication. These small defective genomes can be mimicked by constructing a bacterial plasmid containing the HSV-1 origin of replication and packaging signal, transfecting these recombinant plasmids into mammalian cells, and infecting with a replicating helper virus. The absence of most viral genes in the amplicon vector allows large pieces of foreign DNA (up to 150kbp) to be incorporated. The HSV-1 amplicon is replicated and packaged by the helper virus to form HSV-1 particles containing the amplicon DNA. We constructed a novel HSV-1 amplicon vector system containing lambda phage-derived attR sites to facilitate insertion of transgenes by Invitrogen Gateway recombination. To demonstrate that the amplicon vectors work as expected, we packaged the vector constructs expressing Emerald GFP using the replication-competent helper viruses OK-14 or HSV-mScartlet-I-UL25 in Vero cells and demonstrate that the vector stock can subsequently transduce and express Emerald GFP. In further work, we will insert transgenes into the amplicon vector using Invitrogen Gateway recombination to study their functionality.
ContributorsVelarde, Kimberly (Author) / Hogue, Ian B (Thesis advisor) / Manfredsson, Fredric (Committee member) / Sandoval, Ivette (Committee member) / Varsani, Arvind (Committee member) / Arizona State University (Publisher)
Created2021
Description
Organic light-emitting diodes (OLEDs) have been successfully implemented in various display applications owing to rapid advancements in material design and device architecture. Their success in the display industry has ignited a rising interest in applying OLEDs for solid-state lighting applications through the development of white OLEDs (WOLEDs). However, to enter the market as a serious competitor, WOLEDs must achieve excellent color quality, high external quantum efficiency (EQE) as well as a long operational lifetime. In this research, novel materials and device architectures were explored to improve the performance of single-stack WOLEDs. A new Pt-based phosphorescent emitter, Pt2O2-p2m, was examined as a single emissive emitter for the development of a stable and efficient single-doped WOLED. A bilayer structure was employed to balance the charges carriers within the emissive layer resulting in low efficiency roll-off at high brightness, realizing a peak EQE of 21.5% and EQEs of 20% at 1000 cd m-2 and 15.3% at 7592 cd m-2. A novel phosphorescent/fluorescent, or hybrid, WOLED device architecture was also proposed. To gather a thorough understanding of blue fluorescent OLEDs prior to its use in a WOLED, a study was conducted to investigate the impact of the material selection on the device performance. The use of an anthracene type host demonstrated an improvement to the operational stability of the blue OLED by reducing the occurrence of degradation events. Additionally, various dopant concentrations and blocking materials revealed vastly different efficiency and lifetime results. Finally, a Pd (II) complex, Pd3O8-Py5, with efficient amber-colored aggregate emission was employed to produce a WOLED. Various host materials were investigated to achieve balanced white emission and the addition of an interlayer composed of a high triplet energy material was used to reduce quenching effects. Through this strategy, a color stable WOLED device with a peak EQE of 45% and an estimated LT95 over 50,000 hours at 1000 cd m-2 was realized. The comprehensive performance of the proposed device architecture competes with WOLED devices that are commercially available and reported within the literature domain, providing a strong foundation to further advance the development of highly efficient and stable single-stack WOLEDs.
ContributorsAmeri, Lydia (Author) / Li, Jian (Thesis advisor) / Adams, James (Committee member) / Alford, Terry (Committee member) / Arizona State University (Publisher)
Created2022