Matching Items (81)
Description
The continuing advancement of modulation standards with newer generations of cellular technology, promises ever increasing data rate and bandwidth efficiency. However, these modulation schemes present high peak to average power ratio (PAPR) even after applying crest factor reduction. Being the most power-hungry component in the radio frequency (RF) transmitter, power amplifiers (PA) for infrastructure applications, need to operate efficiently at the presence of these high PAPR signals while maintaining reasonable linearity performance which could be improved by moderate digital pre-distortion (DPD) techniques. This strict requirement of operating efficiently at average power level while being capable of delivering the peak power, made the load modulated PAs such as Doherty PA, Outphasing PA, various Envelope Tracking PAs, Polar transmitters and most recently the load modulated balanced PA, the prime candidates for such application. However, due to its simpler architecture and ability to deliver RF power efficiently with good linearity performance has made Doherty PA (DPA) the most popular solution and has been deployed almost exclusively for wireless infrastructure application all over the world.
Although DPAs has been very successful at amplifying the high PAPR signals, most recent advancements in cellular technology has opted for higher PAPR based signals at wider bandwidth. This lead to increased research and development work to innovate advanced Doherty architectures which are more efficient at back-off (BO) power levels compared to traditional DPAs. In this dissertation, three such advanced Doherty architectures and/or techniques are proposed to achieve high efficiency at further BO power level compared to traditional architecture using symmetrical devices for carrier and peaking PAs. Gallium Nitride (GaN) based high-electron-mobility (HEMT) technology has been used to design and fabricate the DPAs to validate the proposed advanced techniques for higher efficiency with good linearity performance at BO power levels.
Although DPAs has been very successful at amplifying the high PAPR signals, most recent advancements in cellular technology has opted for higher PAPR based signals at wider bandwidth. This lead to increased research and development work to innovate advanced Doherty architectures which are more efficient at back-off (BO) power levels compared to traditional DPAs. In this dissertation, three such advanced Doherty architectures and/or techniques are proposed to achieve high efficiency at further BO power level compared to traditional architecture using symmetrical devices for carrier and peaking PAs. Gallium Nitride (GaN) based high-electron-mobility (HEMT) technology has been used to design and fabricate the DPAs to validate the proposed advanced techniques for higher efficiency with good linearity performance at BO power levels.
ContributorsRuhul Hasin, Muhammad (Author) / Kitchen, Jennifer (Thesis advisor) / Aberle, James T., 1961- (Committee member) / Bakkaloglu, Bertan (Committee member) / Kiaei, Sayfe (Committee member) / Arizona State University (Publisher)
Created2018
Description
Flexible hybrid electronics (FHE) is emerging as a promising solution to combine the benefits of printed electronics and silicon technology. FHE has many high-impact potential areas, such as wearable applications, health monitoring, and soft robotics, due to its physical advantages, which include light weight, low cost and the ability conform to different shapes. However, physical deformations that can occur in the field lead to significant testing and validation challenges. For example, designers have to ensure that FHE devices continue to meet specs even when the components experience stress due to bending. Hence, physical deformation, which is hard to emulate, has to be part of the test procedures developed for FHE devices. This paper is the first to analyze stress experience at different parts of FHE devices under different bending conditions. Then develop a novel methodology to maximize the test coverage with minimum number of text vectors with the help of a mixed integer linear programming formulation.
ContributorsGao, Hang (Author) / Ozev, Sule (Thesis advisor) / Ogras, Umit Y. (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2018
Description
Medical ultrasound imaging is widely used today because of it being non-invasive and cost-effective. Flow estimation helps in accurate diagnosis of vascular diseases and adds an important dimension to medical ultrasound imaging. Traditionally flow estimation is done using Doppler-based methods which only estimate velocity in the beam direction. Thus when blood vessels are close to being orthogonal to the beam direction, there are large errors in the estimation results. In this dissertation, a low cost blood flow estimation method that does not have the angle dependency of Doppler-based methods, is presented.
First, a velocity estimator based on speckle tracking and synthetic lateral phase is proposed for clutter-free blood flow.
Speckle tracking is based on kernel matching and does not have any angle dependency. While velocity estimation in axial dimension is accurate, lateral velocity estimation is challenging due to reduced resolution and lack of phase information. This work presents a two tiered method which estimates the pixel level movement using sum-of-absolute difference, and then estimates the sub-pixel level using synthetic phase information in the lateral dimension. Such a method achieves highly accurate velocity estimation with reduced complexity compared to a cross correlation based method. The average bias of the proposed estimation method is less than 2% for plug flow and less than 7% for parabolic flow.
Blood is always accompanied by clutter which originates from vessel wall and surrounding tissues. As magnitude of the blood signal is usually 40-60 dB lower than magnitude of the clutter signal, clutter filtering is necessary before blood flow estimation. Clutter filters utilize the high magnitude and low frequency features of clutter signal to effectively remove them from the compound (blood + clutter) signal. Instead of low complexity FIR filter or high complexity SVD-based filters, here a power/subspace iteration based method is proposed for clutter filtering. Excellent clutter filtering performance is achieved for both slow and fast moving clutters with lower complexity compared to SVD-based filters. For instance, use of the proposed method results in the bias being less than 8% and standard deviation being less than 12% for fast moving clutter when the beam-to-flow-angle is $90^o$.
Third, a flow rate estimation method based on kernel power weighting is proposed. As the velocity estimator is a kernel-based method, the estimation accuracy degrades near the vessel boundary. In order to account for kernels that are not fully inside the vessel, fractional weights are given to these kernels based on their signal power. The proposed method achieves excellent flow rate estimation results with less than 8% bias for both slow and fast moving clutters.
The performance of the velocity estimator is also evaluated for challenging models. A 2D version of our two-tiered method is able to accurately estimate velocity vectors in a spinning disk as well as in a carotid bifurcation model, both of which are part of the synthetic aperture vector flow imaging (SA-VFI) challenge of 2018. In fact, the proposed method ranked 3rd in the challenge for testing dataset with carotid bifurcation. The flow estimation method is also evaluated for blood flow in vessels with stenosis. Simulation results show that the proposed method is able to estimate the flow rate with less than 9% bias.
First, a velocity estimator based on speckle tracking and synthetic lateral phase is proposed for clutter-free blood flow.
Speckle tracking is based on kernel matching and does not have any angle dependency. While velocity estimation in axial dimension is accurate, lateral velocity estimation is challenging due to reduced resolution and lack of phase information. This work presents a two tiered method which estimates the pixel level movement using sum-of-absolute difference, and then estimates the sub-pixel level using synthetic phase information in the lateral dimension. Such a method achieves highly accurate velocity estimation with reduced complexity compared to a cross correlation based method. The average bias of the proposed estimation method is less than 2% for plug flow and less than 7% for parabolic flow.
Blood is always accompanied by clutter which originates from vessel wall and surrounding tissues. As magnitude of the blood signal is usually 40-60 dB lower than magnitude of the clutter signal, clutter filtering is necessary before blood flow estimation. Clutter filters utilize the high magnitude and low frequency features of clutter signal to effectively remove them from the compound (blood + clutter) signal. Instead of low complexity FIR filter or high complexity SVD-based filters, here a power/subspace iteration based method is proposed for clutter filtering. Excellent clutter filtering performance is achieved for both slow and fast moving clutters with lower complexity compared to SVD-based filters. For instance, use of the proposed method results in the bias being less than 8% and standard deviation being less than 12% for fast moving clutter when the beam-to-flow-angle is $90^o$.
Third, a flow rate estimation method based on kernel power weighting is proposed. As the velocity estimator is a kernel-based method, the estimation accuracy degrades near the vessel boundary. In order to account for kernels that are not fully inside the vessel, fractional weights are given to these kernels based on their signal power. The proposed method achieves excellent flow rate estimation results with less than 8% bias for both slow and fast moving clutters.
The performance of the velocity estimator is also evaluated for challenging models. A 2D version of our two-tiered method is able to accurately estimate velocity vectors in a spinning disk as well as in a carotid bifurcation model, both of which are part of the synthetic aperture vector flow imaging (SA-VFI) challenge of 2018. In fact, the proposed method ranked 3rd in the challenge for testing dataset with carotid bifurcation. The flow estimation method is also evaluated for blood flow in vessels with stenosis. Simulation results show that the proposed method is able to estimate the flow rate with less than 9% bias.
ContributorsWei, Siyuan (Author) / Chakrabarti, Chaitali (Thesis advisor) / Papandreou-Suppappola, Antonia (Committee member) / Ogras, Umit Y. (Committee member) / Wenisch, Thomas F. (Committee member) / Arizona State University (Publisher)
Created2018
Description
This dissertation proposes and presents two different passive sigma-delta
modulator zoom Analog to Digital Converter (ADC) architectures. The first ADC is fullydifferential, synthesizable zoom-ADC architecture with a passive loop filter for lowfrequency Built in Self-Test (BIST) applications. The detailed ADC architecture and a step
by step process designing the zoom-ADC along with a synthesis tool that can target various
design specifications are presented. The design flow does not rely on extensive knowledge
of an experienced ADC designer. Two example set of BIST ADCs have been synthesized
with different performance requirements in 65nm CMOS process. The first ADC achieves
90.4dB Signal to Noise Ratio (SNR) in 512µs measurement time and consumes 17µW
power. Another example achieves 78.2dB SNR in 31.25µs measurement time and
consumes 63µW power. The second ADC architecture is a multi-mode, dynamically
zooming passive sigma-delta modulator. The architecture is based on a 5b interpolating
flash ADC as the zooming unit, and a passive discrete time sigma delta modulator as the
fine conversion unit. The proposed ADC provides an Oversampling Ratio (OSR)-
independent, dynamic zooming technique, employing an interpolating zooming front-end.
The modulator covers between 0.1 MHz and 10 MHz signal bandwidth which makes it
suitable for cellular applications including 4G radio systems. By reconfiguring the OSR,
bias current, and component parameters, optimal power consumption can be achieved for
every mode. The ADC is implemented in 0.13 µm CMOS technology and it achieves an
SNDR of 82.2/77.1/74.2/68 dB for 0.1/1.92/5/10MHz bandwidth with 1.3/5.7/9.6/11.9mW
power consumption from a 1.2 V supply.
modulator zoom Analog to Digital Converter (ADC) architectures. The first ADC is fullydifferential, synthesizable zoom-ADC architecture with a passive loop filter for lowfrequency Built in Self-Test (BIST) applications. The detailed ADC architecture and a step
by step process designing the zoom-ADC along with a synthesis tool that can target various
design specifications are presented. The design flow does not rely on extensive knowledge
of an experienced ADC designer. Two example set of BIST ADCs have been synthesized
with different performance requirements in 65nm CMOS process. The first ADC achieves
90.4dB Signal to Noise Ratio (SNR) in 512µs measurement time and consumes 17µW
power. Another example achieves 78.2dB SNR in 31.25µs measurement time and
consumes 63µW power. The second ADC architecture is a multi-mode, dynamically
zooming passive sigma-delta modulator. The architecture is based on a 5b interpolating
flash ADC as the zooming unit, and a passive discrete time sigma delta modulator as the
fine conversion unit. The proposed ADC provides an Oversampling Ratio (OSR)-
independent, dynamic zooming technique, employing an interpolating zooming front-end.
The modulator covers between 0.1 MHz and 10 MHz signal bandwidth which makes it
suitable for cellular applications including 4G radio systems. By reconfiguring the OSR,
bias current, and component parameters, optimal power consumption can be achieved for
every mode. The ADC is implemented in 0.13 µm CMOS technology and it achieves an
SNDR of 82.2/77.1/74.2/68 dB for 0.1/1.92/5/10MHz bandwidth with 1.3/5.7/9.6/11.9mW
power consumption from a 1.2 V supply.
ContributorsEROL, OSMAN EMIR (Author) / Ozev, Sule (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ogras, Umit Y. (Committee member) / Blain-Christen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2018
Description
The reduced availability of 3He is a motivation for developing alternative neutron detectors. 6Li-enriched CLYC (Cs2LiYCl6), a scintillator, is a promising candidate to replace 3He. The neutron and gamma ray signals from CLYC have different shapes due to the slower decay of neutron pulses. Some of the well-known pulse shape discrimination techniques are charge comparison method, pulse gradient method and frequency gradient method. In the work presented here, we have applied a normalized cross correlation (NCC) approach to real neutron and gamma ray pulses produced by exposing CLYC scintillators to a mixed radiation environment generated by 137Cs, 22Na, 57Co and 252Cf/AmBe at different event rates. The cross correlation analysis produces distinctive results for measured neutron pulses and gamma ray pulses when they are cross correlated with reference neutron and/or gamma templates. NCC produces good separation between neutron and gamma rays at low (< 100 kHz) to mid event rate (< 200 kHz). However, the separation disappears at high event rate (> 200 kHz) because of pileup, noise and baseline shift. This is also confirmed by observing the pulse shape discrimination (PSD) plots and figure of merit (FOM) of NCC. FOM is close to 3, which is good, for low event rate but rolls off significantly along with the increase in the event rate and reaches 1 at high event rate. Future efforts are required to reduce the noise by using better hardware system, remove pileup and detect the NCC shapes of neutron and gamma rays using advanced techniques.
ContributorsChandhran, Premkumar (Author) / Holbert, Keith E. (Thesis advisor) / Spanias, Andreas (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
Description
Kinetic inductance springs from the inertia of charged mobile carriers in alternating electric fields and it is fundamentally different from the magnetic inductance which is only a geometry dependent property. The magnetic inductance is proportional to the volume occupied by the electric and magnetic fields and is often limited by the number of turns of the coil. Kinetic inductance on the other hand is inversely proportional to the density of electrons or holes that exert inertia, the unit mass of the charge carriers and the momentum relaxation time of these charge carriers, all of which can be varied merely by modifying the material properties. Highly sensitive and broadband signal amplifiers often broaden the field of study in astrophysics. Quantum-noise limited travelling wave kinetic inductance parametric amplifiers offer a noise figure of around 0.5 K ± 0.3 K as compared to 20 K in HEMT signal amplifiers and can be designed to operate to cover the entire W-band (75 GHz – 115 GHz).The research cumulating to this thesis involves applying and exploiting kinetic inductance properties in designing a W-band orthogonal mode transducer, quadratic gain phase shifter with a gain of ~49 dB over a meter of microstrip transmission line. The phase shifter will help in measuring the maximum amount of phase shift ∆ϕ_max (I) that can be obtained from half a meter transmission line which helps in predicting the gain of a travelling wave parametric amplifier. In another project, a microstrip to slot line transition is designed and optimized to operate at 150 GHz and 220 GHz frequencies, that is used as a part of horn antenna coupled microwave kinetic inductance detector proposed to operate from 138 GHz to 250 GHz. In the final project, kinetic inductance in a 2D electron gas (2DEG) is explored by design, simulation, fabrication and experimentation. A transmission line model of a 2DEG proposed by Burke (1999), is simulated and verified experimentally by fabricating a capacitvely coupled 2DEG mesa structure. Low temperature experiments were done at 77 K and 10 K with photo-doping the 2DEG. A circuit model of a 2DEG coupled co-planar waveguide model is also proposed and simulated.
ContributorsSurdi, Harshad (Author) / Mauskopf, Philip (Thesis advisor) / Aberle, James T., 1961- (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2016
Description
Historically, wireless communication devices have been developed to process one specific waveform. In contrast, a modern cellular phone supports multiple waveforms corresponding to LTE, WCDMA(3G) and 2G standards. The selection of the network is controlled by software running on a general purpose processor, not by the user. Now, instead of selecting from a set of complete radios as in software controlled radio, what if the software could select the building blocks based on the user needs. This is the new software-defined flexible radio which would enable users to construct wireless systems that fit their needs, rather than forcing to use from a small set of pre-existing protocols.
To develop and implement flexible protocols, a flexible hardware very similar to a Software Defined Radio (SDR) is required. In this thesis, the Intel T2200 board is chosen as the SDR platform. It is a heterogeneous platform with ARM, CEVA DSP and several accelerators. A wide range of protocols is mapped onto this platform and their performance evaluated. These include two OFDM based protocols (WiFi-Lite-A, WiFi-Lite-B), one DFT-spread OFDM based protocol (SCFDM-Lite) and one single carrier based protocol (SC-Lite). The transmitter and receiver blocks of the different protocols are first mapped on ARM in the T2200 board. The timing results show that IFFT, FFT, and Viterbi decoder blocks take most of the transmitter and receiver execution time and so in the next step these are mapped onto CEVA DSP. Mapping onto CEVA DSP resulted in significant execution time savings. The savings for WiFi-Lite-A were 60%, for WiFi-Lite-B were 64%, and for SCFDM-Lite were 71.5%. No savings are reported for SC-Lite since it was not mapped onto CEVA DSP.
Significant reduction in execution time is achieved for WiFi-Lite-A and WiFi-Lite-B protocols by implementing the entire transmitter and receiver chains on CEVA DSP. For instance, for WiFi-Lite-A, the savings were as large as 90%. Such huge savings are because the entire transmitter or receiver chain are implemented on CEVA and the timing overhead due to ARM-CEVA communication is completely eliminated. Finally, over-the-air testing was done for WiFi-Lite-A and WiFi-Lite-B protocols. Data was sent over the air using one Intel T2200 WBS board and received using another Intel T2200 WBS board. The received frames were decoded with no errors, thereby validating the over-the-air-communications.
To develop and implement flexible protocols, a flexible hardware very similar to a Software Defined Radio (SDR) is required. In this thesis, the Intel T2200 board is chosen as the SDR platform. It is a heterogeneous platform with ARM, CEVA DSP and several accelerators. A wide range of protocols is mapped onto this platform and their performance evaluated. These include two OFDM based protocols (WiFi-Lite-A, WiFi-Lite-B), one DFT-spread OFDM based protocol (SCFDM-Lite) and one single carrier based protocol (SC-Lite). The transmitter and receiver blocks of the different protocols are first mapped on ARM in the T2200 board. The timing results show that IFFT, FFT, and Viterbi decoder blocks take most of the transmitter and receiver execution time and so in the next step these are mapped onto CEVA DSP. Mapping onto CEVA DSP resulted in significant execution time savings. The savings for WiFi-Lite-A were 60%, for WiFi-Lite-B were 64%, and for SCFDM-Lite were 71.5%. No savings are reported for SC-Lite since it was not mapped onto CEVA DSP.
Significant reduction in execution time is achieved for WiFi-Lite-A and WiFi-Lite-B protocols by implementing the entire transmitter and receiver chains on CEVA DSP. For instance, for WiFi-Lite-A, the savings were as large as 90%. Such huge savings are because the entire transmitter or receiver chain are implemented on CEVA and the timing overhead due to ARM-CEVA communication is completely eliminated. Finally, over-the-air testing was done for WiFi-Lite-A and WiFi-Lite-B protocols. Data was sent over the air using one Intel T2200 WBS board and received using another Intel T2200 WBS board. The received frames were decoded with no errors, thereby validating the over-the-air-communications.
ContributorsChagari, Vamsi Reddy (Author) / Chakrabarti, Chaitali (Thesis advisor) / Lee, Hyunseok (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2016
Description
Coarse-grained Reconfigurable Arrays (CGRAs) are promising accelerators capable
of accelerating even non-parallel loops and loops with low trip-counts. One challenge
in compiling for CGRAs is to manage both recurring and nonrecurring variables in
the register file (RF) of the CGRA. Although prior works have managed recurring
variables via rotating RF, they access the nonrecurring variables through either a
global RF or from a constant memory. The former does not scale well, and the latter
degrades the mapping quality. This work proposes a hardware-software codesign
approach in order to manage all the variables in a local nonrotating RF. Hardware
provides modulo addition based indexing mechanism to enable correct addressing
of recurring variables in a nonrotating RF. The compiler determines the number of
registers required for each recurring variable and configures the boundary between the
registers used for recurring and nonrecurring variables. The compiler also pre-loads
the read-only variables and constants into the local registers in the prologue of the
schedule. Synthesis and place-and-route results of the previous and the proposed RF
design show that proposed solution achieves 17% better cycle time. Experiments of
mapping several important and performance-critical loops collected from MiBench
show proposed approach improves performance (through better mapping) by 18%,
compared to using constant memory.
of accelerating even non-parallel loops and loops with low trip-counts. One challenge
in compiling for CGRAs is to manage both recurring and nonrecurring variables in
the register file (RF) of the CGRA. Although prior works have managed recurring
variables via rotating RF, they access the nonrecurring variables through either a
global RF or from a constant memory. The former does not scale well, and the latter
degrades the mapping quality. This work proposes a hardware-software codesign
approach in order to manage all the variables in a local nonrotating RF. Hardware
provides modulo addition based indexing mechanism to enable correct addressing
of recurring variables in a nonrotating RF. The compiler determines the number of
registers required for each recurring variable and configures the boundary between the
registers used for recurring and nonrecurring variables. The compiler also pre-loads
the read-only variables and constants into the local registers in the prologue of the
schedule. Synthesis and place-and-route results of the previous and the proposed RF
design show that proposed solution achieves 17% better cycle time. Experiments of
mapping several important and performance-critical loops collected from MiBench
show proposed approach improves performance (through better mapping) by 18%,
compared to using constant memory.
ContributorsDave, Shail (Author) / Shrivastava, Aviral (Thesis advisor) / Ren, Fengbo (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2016
Description
We present fast and robust numerical algorithms for 3-D scattering from perfectly electrical conducting (PEC) and dielectric random rough surfaces in microwave remote sensing. The Coifman wavelets or Coiflets are employed to implement Galerkin’s procedure in the method of moments (MoM). Due to the high-precision one-point quadrature, the Coiflets yield fast evaluations of the most off-diagonal entries, reducing the matrix fill effort from O(N^2) to O(N). The orthogonality and Riesz basis of the Coiflets generate well conditioned impedance matrix, with rapid convergence for the conjugate gradient solver. The resulting impedance matrix is further sparsified by the matrix-formed standard fast wavelet transform (SFWT). By properly selecting multiresolution levels of the total transformation matrix, the solution precision can be enhanced while matrix sparsity and memory consumption have not been noticeably sacrificed. The unified fast scattering algorithm for dielectric random rough surfaces can asymptotically reduce to the PEC case when the loss tangent grows extremely large. Numerical results demonstrate that the reduced PEC model does not suffer from ill-posed problems. Compared with previous publications and laboratory measurements, good agreement is observed.
ContributorsZhang, Lisha (Author) / Pan, George (Thesis advisor) / Diaz, Rodolfo (Committee member) / Aberle, James T., 1961- (Committee member) / Yu, Hongbin (Committee member) / Arizona State University (Publisher)
Created2016
Description
Articially engineered two-dimensional materials, which are widely known as
metasurfaces, are employed as ground planes in various antenna applications. Due to
their nature to exhibit desirable electromagnetic behavior, they are also used to design
waveguiding structures, absorbers, frequency selective surfaces, angular-independent
surfaces, etc. Metasurfaces usually consist of electrically small conductive planar
patches arranged in a periodic array on a dielectric covered ground plane. Holographic
Articial Impedance Surfaces (HAISs) are one such metasurfaces that are capable of
forming a pencil beam in a desired direction, when excited with surface waves. HAISs
are inhomogeneous surfaces that are designed by modulating its surface impedance.
This surface impedance modulation creates a periodical discontinuity that enables a
part of the surface waves to leak out into the free space leading to far-eld radia-
tion. The surface impedance modulation is based on the holographic principle. This
dissertation is concentrated on designing HAISs with
Desired polarization for the pencil beam
Enhanced bandwidth
Frequency scanning
Conformity to curved surfaces
HAIS designs considered in this work include both one and two dimensional mod-
ulations. All the designs and analyses are supported by mathematical models and
HFSS simulations.
metasurfaces, are employed as ground planes in various antenna applications. Due to
their nature to exhibit desirable electromagnetic behavior, they are also used to design
waveguiding structures, absorbers, frequency selective surfaces, angular-independent
surfaces, etc. Metasurfaces usually consist of electrically small conductive planar
patches arranged in a periodic array on a dielectric covered ground plane. Holographic
Articial Impedance Surfaces (HAISs) are one such metasurfaces that are capable of
forming a pencil beam in a desired direction, when excited with surface waves. HAISs
are inhomogeneous surfaces that are designed by modulating its surface impedance.
This surface impedance modulation creates a periodical discontinuity that enables a
part of the surface waves to leak out into the free space leading to far-eld radia-
tion. The surface impedance modulation is based on the holographic principle. This
dissertation is concentrated on designing HAISs with
Desired polarization for the pencil beam
Enhanced bandwidth
Frequency scanning
Conformity to curved surfaces
HAIS designs considered in this work include both one and two dimensional mod-
ulations. All the designs and analyses are supported by mathematical models and
HFSS simulations.
ContributorsPandi, Sivaseetharaman (Author) / Balanis, Constantine A (Thesis advisor) / Palais, Joseph (Committee member) / Aberle, James T., 1961- (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2017