Matching Items (24)
Filtering by
- Genre: Doctoral Dissertation
Description
This work examines star formation in the debris associated with collisions of dwarf and spiral galaxies. While the spectacular displays of major mergers are famous (e.g., NGC 4038/9, ``The Antennae''), equal mass galaxy mergers are relatively rare compared to minor mergers (mass ratio <0.3) Minor mergers are less energetic than major mergers, but more common in the observable universe and, thus, likely played a pivotal role in the formation of most large galaxies. Centers of mergers host vigorous star formation from high gas density and turbulence and are surveyed over cosmological distances. However, the tidal debris resulting from these mergers have not been well studied. Such regions have large reservoirs of gaseous material that can be used as fuel for subsequent star formation but also have lower gas density. Tracers of star formation at the local and global scale have been examined for three tidal tails in two minor merger systems. These tracers include young star cluster populations, H-alpha, and [CII] emission. The rate of apparent star formation derived from these tracers is compared to the gas available to estimate the star formation efficiency (SFE). The Western tail of NGC 2782 formed isolated star clusters while massive star cluster complexes are found in the UGC 10214 (``The Tadpole'') and Eastern tail of NGC 2782. Due to the lack of both observable CO and [CII] emission, the observed star formation in the Western tail of NGC 2782 may have a low carbon abundance and represent only the first round of local star formation. While the Western tail has a normal SFE, the Eastern tail in the same galaxy has an low observed SFE. In contrast, the Tadpole tidal tail has a high observed star formation rate and a corresponding high SFE. The low SFE observed in the Eastern tail of NGC 2782 may be due to its origin as a splash region where localized gas heating is important. However, the other tails may be tidally formed regions where gravitational compression likely dominates and enhances the local star formation.
ContributorsKnierman, Karen A (Author) / Scowen, Paul (Thesis advisor) / Groppi, Christopher (Thesis advisor) / Mauskopf, Philip (Committee member) / Windhorst, Rogier (Committee member) / Jansen, Rolf (Committee member) / Arizona State University (Publisher)
Created2013
Description
A thorough exploration of star formation necessitates observation across the electromagnetic spectrum. In particular, observations in the submillimeter and ultra-violet allow one to observe very early stage star formation and to trace the evolution from molecular cloud collapse to stellar ignition. Submillimeter observations are essential for piercing the heart of heavily obscured stellar nurseries to observe star formation in its infancy. Ultra-violet observations allow one to observe stars just after they emerge from their surrounding environment, allowing higher energy radiation to escape. To make detailed observations of early stage star formation in both spectral regimes requires state-of-the-art detector technology and instrumentation. In this dissertation, I discuss the calibration and feasibility of detectors developed by Lawrence Berkeley National Laboratory and specially processed at the Jet Propulsion Laboratory to increase their quantum efficiency at far-ultraviolet wavelengths. A cursory treatment of the delta-doping process is presented, followed by a thorough discussion of calibration procedures developed at JPL and in the Laboratory for Astronomical and Space Instrumentation at ASU. Subsequent discussion turns to a novel design for a Modular Imager Cell forming one possible basis for construction of future large focal plane arrays. I then discuss the design, fabrication, and calibration of a sounding rocket imaging system developed using the MIC and these specially processed detectors. Finally, I discuss one scientific application of sub-mm observations. I used data from the Heinrich Hertz Sub-millimeter Telescope and the Sub-Millimeter Array (SMA) to observe sub-millimeter transitions and continuum emission towards AFGL 2591. I tested the use of vibrationally excited HCN emission to probe the protostellar accretion disk structure. I measured vibrationally excited HCN line ratios in order to elucidate the appropriate excitation mechanism. I find collisional excitation to be dominant, showing the emission originates in extremely dense (n&sim10;11 cm-3), warm (T&sim1000; K) gas. Furthermore, from the line profile of the v=(0, 22d, 0) transition, I find evidence for a possible accretion disk.
ContributorsVeach, Todd Justin (Author) / Scowen, Paul A (Thesis advisor) / Groppi, Christopher E (Thesis advisor) / Beasley, Matthew N (Committee member) / Rhoads, James E (Committee member) / Windhorst, Rogier A (Committee member) / Arizona State University (Publisher)
Created2012
Description
The continuous time-tagging of photon arrival times for high count rate sources isnecessary for applications such as optical communications, quantum key encryption,
and astronomical measurements. Detection of Hanbury-Brown and Twiss (HBT) single
photon correlations from thermal sources, such as stars, requires a combination of high
dynamic range, long integration times, and low systematics in the photon detection
and time tagging system. The continuous nature of the measurements and the need
for highly accurate timing resolution requires a customized time-to-digital converter
(TDC). A custom built, two-channel, field programmable gate array (FPGA)-based
TDC capable of continuously time tagging single photons with sub clock cycle timing
resolution was characterized. Auto-correlation and cross-correlation measurements
were used to constrain spurious systematic effects in the pulse count data as a function
of system variables. These variables included, but were not limited to, incident
photon count rate, incoming signal attenuation, and measurements of fixed signals.
Additionally, a generalized likelihood ratio test using maximum likelihood estimators
(MLEs) was derived as a means to detect and estimate correlated photon signal
parameters. The derived GLRT was capable of detecting correlated photon signals in
a laboratory setting with a high degree of statistical confidence. A proof is presented
in which the MLE for the amplitude of the correlated photon signal is shown to be the
minimum variance unbiased estimator (MVUE). The fully characterized TDC was used
in preliminary measurements of astronomical sources using ground based telescopes.
Finally, preliminary theoretical groundwork is established for the deep space optical
communications system of the proposed Breakthrough Starshot project, in which
low-mass craft will travel to the Alpha Centauri system to collect scientific data from
Proxima B. This theoretical groundwork utilizes recent and upcoming space based
optical communication systems as starting points for the Starshot communication
system.
ContributorsHodges, Todd Michael William (Author) / Mauskopf, Philip (Thesis advisor) / Trichopoulos, George (Thesis advisor) / Papandreou-Suppappola, Antonia (Committee member) / Bliss, Daniel (Committee member) / Arizona State University (Publisher)
Created2022
Description
Undersea scientific ocean exploration and research only began in earnest approximately150 years ago. Much has been learned and discovered in that time, but there are also gaps in understanding of the ocean depths. One source of the knowledge gap is the relative lack of crewed exploration in some regions of the ocean. This work presents a vehicle that provides divers with longer time at deeper depths than is currently available in an unpressurized environment, reduces diver workload, and improves situational awareness. Working in collaboration with the scientific diver community, top-level requirements were defined, and a Concept of Operations was developed. This effort is followed up with a vehicle design which provides the capability for two divers to complete unpressurized dives to 200 meters, remain there for 20 minutes, and return to the surface within 12 hours. Additional functionality provided by the vehicle includes significant cargo capacity, voice and data communication with the surface, geolocation capabilities, and automated maneuvering and decompression management. Analysis of the hull shape and propulsion system is presented which demonstrates that the vehicle can reach its velocity and acceleration performance requirements. A virtual environment is then presented which has the potential to allow for end-to-end mission performance evaluation. Finally, the constraints on the life support system are discussed and source code for a simulation is presented. The final chapter of this work examines a hypothetical mission to 200 meters depth. The various phases of the mission are discussed as well as the potential consumption of both oxygen and electricity. Two life support gas mixtures are examined, and the resulting decompression profiles are presented. The final analysis shows that it is possible to conduct dives to 200 meters, perform 20 minutes of work, and return to the surface within 12 hours using the CUTLASS vehicle that is presented.
ContributorsBennett, Kirk (Author) / Scowen, Paul A (Thesis advisor) / Butler, Nathaniel R (Thesis advisor) / Robinson, Mark S (Committee member) / Groppi, Christopher E (Committee member) / Bryan, Sean A (Committee member) / Arizona State University (Publisher)
Created2022
Description
TolTEC is a three-band millimeter-wave, imaging polarimeter installed on the 50 m diameter Large Millimeter Telescope (LMT) in Mexico. This camera simultaneously images the focal plane at three wavebands centered at 1.1 mm (270 GHz), 1.4 mm (214 GHz), and 2.0 mm (150 GHz). TolTEC combines polarization-sensitive kinetic inductance detectors (KIDs) with the LMT to produce high resolution images of the sky in both total intensity and polarization. I present an overview of the TolTEC camera’s optical system and my contributions to the optomechanical design and characterization of the instrument. As part of my work with TolTEC, I designed the mounting structures for the cold optics within the cryostat accounting for thermal contraction to ensure the silicon lenses do not fracture when cooled. I also designed the large warm optics that re-image the light from the telescope, requiring me to perform static and vibration analyses to ensure the mounts correctly supported the mirrors. I discuss the various methods used to align the optics and the cryostat in the telescope. I discuss the Zemax optical model of TolTEC and compare it with measurements of the instrument to help with characterization. Finally, I present the results of stacking galaxies on data from the Atacama Cosmology Telescope (ACT) to measure the Sunyaev-Zel’dovich (SZ) effect and estimate the thermal energy in the gas around high red-shift, quiescent galaxies as an example of science that could be done with TolTEC data. Since the camera combines high angular resolution with images at three wavelengths near distinct SZ features, TolTEC will provide precise measurements to learn more about these types of galaxies.
ContributorsLunde, Emily Louise (Author) / Mauskopf, Philip (Thesis advisor) / Groppi, Christopher (Committee member) / Scannapieco, Evan (Committee member) / Noble, Allison (Committee member) / Bryan, Sean (Committee member) / Arizona State University (Publisher)
Created2023
Description
The work covered in this dissertation addresses two areas revolving around superconducting nanowire detector development. The first is regarding array architectureused for a large-scale system. The second involves operating under conditions that
allow for a linear response in a superconducting nanowire detector. This dissertation
provides the relevant theory, design, and measurements to characterize these detectors. The array architecture studied here utilizes a superconducting nanowire single
photon detector embedded in an LC resonant structure, allowing multiple pixels to
couple to a single transmission line and identify each one by a tuned characteristic frequency. The pixels in the array are DC-biased, allowing them to respond to absorbed
single photons and avoiding any dead time associated with RF biasing. Measured
results from a 16-pixel array based on chip components are analyzed. The development here directs this architecture towards integrating a proven 16-pixel design onto
a single substrate with the capacity to scale to a higher pixel count and integrate
into a broad range of applications. This text outlines the theory behind the proposed
linear operation regime and details the considerations needed to achieve a response.
The basic principle relies on the time-dependent change in kinetic inductance due to
an absorbed photon. Under the conditions discussed in the text, this would allow
for fast photon number resolution. However, without reaching those conditions, the
detector may still operate under a higher incident photon flux. Two device designs
are formulated and simulated, weighing the benefits and drawbacks of each approach.
One of the device designs uses an impedance-matching taper to minimize reflections
between the nanowire and 50 Ohm amplifier. The other design utilizes N parallel
nanowires spanning the length of a gap along a 50 Ohm transmission line path. The
tapered device is realized to a proof-of-principle stage and measured under conditions
that set a limit on the device’s linear response to optical power. The performance of this detector points to areas of improvement that are addressed or circumvented
in the parallel bridge design. Potential for future development is discussed for the
frequency multiplexed superconducting nanowire single photon detector array and
the linear mode detector.
ContributorsGlasby, Jacob (Author) / Mauskopf, Philip (Thesis advisor) / Chamberlin, Ralph (Committee member) / Schmidt, Kevin (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2023
Description
As a demonstration study of low-resolution spectrophotometry, the photometric redshift estimation with narrow-band optical photometry of nine galaxy clusters is presented in this thesis. A complete data reduction process of the photometryusing up to 16 10nm wide narrow-band optical filters from 490nm − 660nm are provided. Narrow-band photometry data are combined with broad-band photometry (SDSS/Pan-STARRS) for photometric redshift fitting. With available spectroscopic
redshift data from eight of the fields, I evaluated the fitted photometric redshift results and showed that combining broad-band photometric data with narrow-band data result in improvements of factor 2-3, compared to redshift estimations from
broad-band photometry alone. With 15 or 16 narrow-band data combined with SDSS (Sloan Digital Sky Survey) or Pan-STARRS1 (The Panoramic Survey Telescope and Rapid Response System) data, a Normalized Median Absolute Deviation of σNMAD ∼ 0.01−0.016 can be achieved.
The multiband images of galaxy cluster ABELL 611 have been used to further study intracluster light around its brightest cluster galaxy (BCG). It can be shown here that fitting of BCG+ICL stellar properties using the averaged 1-dimensional
radial profile is possible up to ∼ 100kpc within this cluster. The decreasing in age of the stellar population as a function of radius from the BCG+ICL profile, though not entirely conclusive, demonstrates possible future application of low-resolution
spectrophotometry on the ICL studies.
Finally, Spectro-Photometer for the History of the Universe, Epoch of Reionization, and Ices Explorer (SPHEREx) mission planning study are covered, and a methodology of visualization tool for target availability is described.
ContributorsWang, Pao-Yu (Author) / Mauskopf, Philip (Thesis advisor) / Butler, Nathaniel (Committee member) / Jansen, Rolf (Committee member) / Vachaspati, Tanmay (Committee member) / Arizona State University (Publisher)
Created2022
Description
This dissertation presents a comprehensive study on the advancement of astrophysical radio, microwave, and terahertz instrumentation/simulations with three pivotal components.First, theoretical simulations of high metallicity galaxies are conducted using the supercomputing resources of Purdue University and NASA. These simulations model the evolution
of a gaseous cloud akin to a nascent galaxy, incorporating variables such as kinetic energy,
mass, radiation fields, magnetic fields, and turbulence. The objective is to scrutinize the
spatial distribution of various isotopic elements in galaxies with unusually high metallicities and measure the effects of magnetic fields on their structural distribution.
Next, I proceed with an investigation of the technology used for reading out Microwave Kinetic Inductance Detectors (MKIDs) and their dynamic range limitations tied to the current
method of FPGA-based readout firmware. In response, I introduce an innovative algorithm
that employs PID controllers and phase-locked loops for tracking the natural frequencies
of resonator pixels, thereby eliminating the need for costly mid-observation frequency recalibrations which currently hinder the widespread use of MKID arrays.
Finally, I unveil the novel Spectroscopic Lock-in Firmware (SpLiF) algorithm designed to
address the pernicious low-frequency noise plaguing emergent quantum-limited detection
technologies. The SpLiF algorithm harmonizes the mathematical principles of lock-in amplification with the capabilities of a Fast Fourier Transform to protect spectral information
from pink noise and other low-frequency noise contributors inherent to most detection systems. The efficacy of the SpLiF algorithm is substantiated through rigorous mathematical
formulation, software simulations, firmware simulations, and benchtop lab results.
ContributorsHoh, Jonathan (Author) / Groppi, Christopher E (Thesis advisor) / Jamison-Hooks, Tracee (Committee member) / Buie II, Edward (Committee member) / Trichopoulos, Georgios (Committee member) / Scannapieco, Evan (Committee member) / Arizona State University (Publisher)
Created2024
Description
Millimeter wave technologies have various applications in many science and engineering disciplines, from astronomy and chemistry to medicine and security. The superconducting circuit technology, in particular mm-wave, is one of the most appealing candidates due to their extremely low loss, near quantum-limited noise performance, and scalable fabrication. Two main immediate applications of these devices are in astronomical instrumentation and quantum computing and sensing. The kinetic inductance caused by the inertia of cooper pairs in thin-film superconductors dominates over the geometric inductance of the superconducting circuit. The nonlinear response of the kinetic inductance to an applied field or current provides a Kerr-like medium. This nonlinear platform can be used for mixing processes, parametric gain, and anharmonic resonance. In this thesis, I present the development of an mm-wave superconducting on-chip Fourier transform spectrometer (SOFTS) based on a nonlinear kinetic inductance of superconducting thin films. The circuit elements of the SOFTS device include a quadrature hybrid and current-controllable superconducting transmission lines in an inverted microstrip geometry. Another similar device explored here is a kinetic inductance traveling wave parametric amplifier (KI-TWPA) with wide instantaneous bandwidth, quantum noise limited performance, and high dynamic range as a candidate for the readout of cryogenic detectors and superconducting qubits. I report four-wave mixing gain measurements of ~ 30 dB from 0.2 - 5 GHz in KI-TWPAs made of capacitively shunted microstrip lines. I show that the gain can be tuned over the above-mentioned frequency range by changing the pump tone frequency. I also discuss the measured gain (~ 6 dB) of a prototype mm-wave KI-TWPA in the 75 - 100 GHz frequency range. Finally, I present, for the first time, the concept and simulation of a kinetic inductance qubit I named Kineticon. The qubit exploits the nonlinearity of the kinetic inductance of a very thin nanowire connecting two capacitive pads with a resonant frequency of ~ 96 GHz. the qubit is embedded in an mm-wave aluminum cavity. I show that mm-wave anharmonic microstrip resonators made of NbTiN have quality factors > 60,000. These measurements are promising for implementing high-quality factor resonators and qubits in the mm-wave regime.
ContributorsFaramarzi, Farzad (Author) / Mauskopf, Philip (Thesis advisor) / Day, Peter (Committee member) / Chamberlin, Ralph (Committee member) / Terrano, William (Committee member) / Arizona State University (Publisher)
Created2023
Description
Studying the interstellar medium (ISM) is the key to answering questions about how material that exists between the stars drives the evolution of galaxies. Current models for the ISM life-cycle exist, but several steps lack observational evidence. Inthis dissertation I present the work I completed in support of up-coming mission to further study the ISM. This work includes ancillary data analysis of the Carina Nebula for the upcoming balloon mission: astrophysics stratospheric telescope for
high spectral resolution observations at submillimeter wavelengths (ASTHROS). I present a derived molecular gas map of Carina from Herschel dust continuum emission maps at wavelengths between 70-500 microns. I compare it to the distribution
of atomic gas, using HI 21 cm data, and of multiple CO isotopologues for the J = 1 → 0 rotational transition. I use these data sets to separate the CO–dark and CO–bright molecular components to study their relative contribution to the total molecular gas mass budget in Carina. I studied the transition between atomic and molecular gas in this region, by deriving the molecular fraction as a function of position, and comparing it to theoretical models of this transition. I also present the flight hardware design, testing, and space qualification of the intermediate frequency (IF) harness for the galactic/extragalactic ultra long duration balloon spectroscopic terahertz observatory (GUSTO). The harness transmits signal via novel cryogenic flexible stripline based transmission lines operating from 0.3 - 6.0 GHz. I designed three sets of 8-channel ribbons with characteristic insertion loss of 3.07 dB/ft at 5 GHz while the line was at a temperature gradient between 20 K - 300 K. Missions like GUSTO make use of non-linear mixing elements to achieve down-conversion of higher frequencies into IF bands. The mixers have a temperature dependent impedance that is difficult to measure. The last chapters of this work detail my attempt to carry out in-situ vacuum cryogenic calibrations using industry standard commercial off-the-shelf calibration kits and cryogenic RF electro-mechanical latching switches. I present the complex impedance of a non-linear superconducting transmission line as measured with a cryogenic calibration.
ContributorsNeric, Marko (Author) / Groppi, Chris (Thesis advisor) / Mauskopf, Philip (Committee member) / Scowen, Paul (Committee member) / Trichopoulos, Georgios (Committee member) / Jacobs, Daniel (Committee member) / Arizona State University (Publisher)
Created2023