Matching Items (3)
Filtering by
- Creators: Ozev, Sule
Description
Voltage Control Oscillator (VCO) is one of the most critical blocks in Phase Lock Loops (PLLs). LC-tank VCOs have a superior phase noise performance, however they require bulky passive resonators and often calibration architectures to overcome their limited tuning range. Ring oscillator (RO) based VCOs are attractive for digital technology applications owing to their ease of integration, small die area and scalability in deep submicron processes. However, due to their supply sensitivity and poor phase noise performance, they have limited use in applications demanding low phase noise floor, such as wireless or optical transceivers. Particularly, out-of-band phase noise of RO-based PLLs is dominated by RO performance, which cannot be suppressed by the loop gain, impairing RF receiver's sensitivity or BER of optical clock-data recovery circuits. Wide loop bandwidth PLLs can overcome RO noise penalty, however, they suffer from increased in-band noise due to reference clock, phase-detector and charge-pump. The RO phase noise is determined by the noise coming from active devices, supply, ground and substrate. The authors adopt an auxiliary circuit with inverse delay sensitivity to supply noise, which compensates for the delay variation of inverter cells. Feed-forward noise-cancelling architecture that improves phase noise characteristic of RO based PLLs is presented. The proposed circuit dynamically attenuates RO phase noise contribution outside the PLL bandwidth, or in a preferred band. The implemented noise-cancelling loop potentially enables application of RO based PLL for demanding frequency synthesizers applications, such as optical links or high-speed serial I/Os.
ContributorsMin, Seungkee (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Towe, Bruce (Committee member) / Arizona State University (Publisher)
Created2011
Description
An investigation of phase noise in amplifier and voltage-controller oscillator (VCO) circuits was conducted to show that active direct-current (DC) bias techniques exhibit lower phase noise performance than traditional resistive DC bias techniques. Low-frequency high-gain amplifiers like those found in audio applications exhibit much better 1/f phase noise performance and can be used to bias amplifier or VCO circuits that work at much higher frequencies to reduce the phase modulation caused by higher frequency devices. An improvement in single-side-band (SSB) phase noise of 15 dB at offset frequencies less than 50 KHz was simulated and measured. Residual phase noise of an actively biased amplifier also exhibited significant noise improvements when compared to an equivalent resistive biased amplifier.
ContributorsBaldwin, Jeremy Bart (Author) / Aberle, James T., 1961- (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2010
Description
This work analyzes and develops a point-of-load (PoL) synchronous buck converter using enhancement-mode Gallium Nitride (e-GaN), with emphasis on optimizing reverse conduction loss by using a well-known technique of placing an anti-parallel Schottky diode across the synchronous power device. This work develops an improved analytical switching model for the GaN-based converter with the Schottky diode using piecewise linear approximations.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
ContributorsKoli, Gauri (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2020