Matching Items (5)
Filtering by
- All Subjects: Geomembranes
- Genre: Academic theses
- Genre: Masters Thesis
- Creators: Kavazanjian, Edward
- Creators: Cadillo – Quiroz, Hinsby
- Resource Type: Text
Description
A series of experiments were conducted to support validation of a numerical model for the performance of geomembrane liners subject to waste settlement and seismic loading. These experiments included large scale centrifuge model testing of a geomembrane-lined landfill, small scale laboratory testing to get the relevant properties of the materials used in the large scale centrifuge model, and tensile tests on seamed geomembrane coupons. The landfill model in the large scale centrifuge test was built with a cemented sand base, a thin film NafionTM geomembrane liner, and a mixture of sand and peat for model waste. The centrifuge model was spun up to 60 g, allowed to settle, and then subjected to seismic loading at three different peak ground accelerations (PGA). Strain on the liner and settlement of the waste during model spin-up and subsequent seismic loading and accelerations throughout the model due to seismic loading were acquired from sensors within the model. Laboratory testing conducted to evaluate the properties of the materials used in the model included triaxial compression tests on the cemented sand base, wide-width tensile testing of the thin film geomembrane, interface shear testing between the thin film geomembrane and the waste material, and one dimensional compression and cyclic direct simple shear testing of the sand-peat mixture used to simulate the waste. The tensile tests on seamed high-density polyethylene (HDPE) coupons were conducted to evaluate strain concentration associated with seams oriented perpendicular to an applied tensile load. Digital image correlation (DIC) was employed to evaluate the strain field, and hence seam strain concentrations, in these tensile tests. One-dimensional compression tests were also conducted on composite sand and HDPE samples to evaluate the compressive modulus of HDPE. The large scale centrifuge model and small scale laboratory tests provide the necessary data for numerical model validation. The tensile tests on seamed HDPE specimens show that maximum tensile strain due to strain concentrations at a seam is greater than previously suggested, a finding with profound implications for landfill liner design and construction quality control/quality assurance (QC/QA) practices. The results of the one-dimensional compression tests on composite sand-HDPE specimens were inconclusive.
ContributorsGutierrez, Angel (Author) / Kavazanjian, Edward (Thesis advisor) / Zapata, Claudia (Committee member) / Jang, Jaewon (Committee member) / Arizona State University (Publisher)
Created2016
Description
A numerical model for design of the geomembrane elements of waste containment systems has been validated by laboratory testing. Due to the absence of any instrumented case histories of seismic performance of geomembrane liner systems, a large scale centrifuge test of a model geomembrane-lined landfill subject to seismic loading was conducted at the University of California at Davis Centrifuge Test facility as part of National Science Foundation Network for Earthquake the Engineering Simulation Research (NEESR) program. Data collected in the large scale centrifuge test included waste settlement, liner strains and earthquake accelerations at various locations throughout the model. This data on landfill and liner seismic performance has been supplemented with additional laboratory and small scale centrifuge tests to determine the parameters required for the numerical model, including strength and stiffness of the model materials, interface shear strengths, and interface stiffness. The numerical model explicitly assesses the forces and strains in the geomembrane elements of a containment system to subject to both static and seismic loads the computer code FLACTM, a finite difference program for non-linear analysis of continua. The model employs a beam element with zero moment of inertia and with interface elements on both sides to model to represent the geomembrane elements in the liner system. The model also includes non-linear constitutive models for the stress-strain behavior of geomembrane beam elements and an elastic-perfectly plastic model for the load-displacement behavior of the beam interfaces. Parametric studies are conducted with the validated numerical model to develop recommendations for landfill design, construction, and construction quality assurance.
ContributorsWu, Xuan (Ph.D. in civil and environmental engineering) (Author) / Kavazanjian, Edward (Thesis advisor) / Zapata, Claudia (Committee member) / Jang, Jaewon (Committee member) / Arizona State University (Publisher)
Created2017
Description
Laboratory testing was conducted to quantify strain concentrations adjacent to seams and scratches in high density polyethylene (HDPE) geomembranes. The tensile strain profile of remnants meeting the ASTM criteria for wide-width tensile testing from samples of field seams recovered for construction quality assurance testing was evaluated using digital image correlation (DIC). Strains adjacent to scratches on laboratory prepared samples loaded in tension were also measured using DIC. The tensile strain in the zone adjacent to a seam and the tensile strain adjacent to a scratch were compared to the tensile strains calculated using theoretical strain concentration factors. The relationship between the maximum tensile strain adjacent to a seam and the global nominal strain in the sample was quantified for textured and smooth geomembranes of common thicknesses. Using statistical analysis of the data, bounds were developed for the allowable nominal tensile strain expected to induce maximum tensile strains adjacent to the seam less than or equal to the typical yield strain of HDPE geomembranes, at several confidence levels. Where nominal strain is the global or average strain applied to the sample and maximum strain is the largest tensile strain induced in the sample.
The reduction in the nominal yield strain due to a scratch in a HDPE geomembrane was also quantified. The yield strain was approximately the same as predicted using theoretical strain concentration factors. The difference in the average measured maximum strains adjacent to the seams of textured and smooth HDPE geomembranes was found to be statistically insignificant. However, maximum strains adjacent to extrusion welded seams were somewhat greater than adjacent to fusion welded seams for nominal strains on the order of 3% to 4%. The results of the testing program suggest that the nominal tensile strain should be limited to 4% around dual hot wedge seams and 3% around extrusion fillet seams to avoid maximum strains equal to 11%, a typical yield strain for HDPE geomembranes.
The reduction in the nominal yield strain due to a scratch in a HDPE geomembrane was also quantified. The yield strain was approximately the same as predicted using theoretical strain concentration factors. The difference in the average measured maximum strains adjacent to the seams of textured and smooth HDPE geomembranes was found to be statistically insignificant. However, maximum strains adjacent to extrusion welded seams were somewhat greater than adjacent to fusion welded seams for nominal strains on the order of 3% to 4%. The results of the testing program suggest that the nominal tensile strain should be limited to 4% around dual hot wedge seams and 3% around extrusion fillet seams to avoid maximum strains equal to 11%, a typical yield strain for HDPE geomembranes.
ContributorsAndresen, Jake (Author) / Kavazanjian, Edward (Thesis advisor) / Houston, Sandra (Committee member) / Zapata, Claudia (Committee member) / Arizona State University (Publisher)
Created2017
Characterization and Manipulation of Microbiomes From Arid Landfills for Improved Methane Production
Description
Environmentally harmful byproducts from solid waste’s decomposition, including methane (CH4) emissions, are managed through standardized landfill engineering and gas-capture mechanisms. Yet only a limited number of studies have analyzed the development and composition of Bacteria and Archaea involved in CH4 production from landfills. The objectives of this research were to compare microbiomes and bioactivity from CH4-producing communities in contrasting spatial areas of arid landfills and to tests a new technology to biostimulate CH4 production (methanogenesis) from solid waste under dynamic environmental conditions controlled in the laboratory. My hypothesis was that the diversity and abundance of methanogenic Archaea in municipal solid waste (MSW), or its leachate, play an important role on CH4 production partially attributed to the group’s wide hydrogen (H2) consumption capabilities. I tested this hypothesis by conducting complementary field observations and laboratory experiments. I describe niches of methanogenic Archaea in MSW leachate across defined areas within a single landfill, while demonstrating functional H2-dependent activity. To alleviate limited H2 bioavailability encountered in-situ, I present biostimulant feasibility and proof-of-concepts studies through the amendment of zero valent metals (ZVMs). My results demonstrate that older-aged MSW was minimally biostimulated for greater CH4 production relative to a control when exposed to iron (Fe0) or manganese (Mn0), due to highly discernable traits of soluble carbon, nitrogen, and unidentified fluorophores found in water extracts between young and old aged, starting MSW. Acetate and inhibitory H2 partial pressures accumulated in microcosms containing old-aged MSW. In a final experiment, repeated amendments of ZVMs to MSW in a 600 day mesocosm experiment mediated significantly higher CH4 concentrations and yields during the first of three ZVM injections. Fe0 and Mn0 experimental treatments at mesocosm-scale also highlighted accelerated development of seemingly important, but elusive Archaea including Methanobacteriaceae, a methane-producing family that is found in diverse environments. Also, prokaryotic classes including Candidatus Bathyarchaeota, an uncultured group commonly found in carbon-rich ecosystems, and Clostridia; All three taxa I identified as highly predictive in the time-dependent progression of MSW decomposition. Altogether, my experiments demonstrate the importance of H2 bioavailability on CH4 production and the consistent development of Methanobacteriaceae in productive MSW microbiomes.
ContributorsReynolds, Mark Christian (Author) / Cadillo-Quiroz, Hinsby (Thesis advisor) / Krajmalnik-Brown, Rosa (Thesis advisor) / Wang, Xuan (Committee member) / Kavazanjian, Edward (Committee member) / Arizona State University (Publisher)
Created2022
Description
Zero-Valent Metals (ZVM) are highly reactive materials and have been proved to be effective in contaminant reduction in soils and groundwater remediation. In fact, zero-Valent Iron (ZVI) has proven to be very effective in removing, particularly chlorinated organics, heavy metals, and odorous sulfides. Addition of ZVI has also been proved in enhancing the methane gas generation in anaerobic digestion of activated sludge. However, no studies have been conducted regarding the effect of ZVM stimulation to Municipal Solid Waste (MSW) degradation. Therefore, a collaborative study was developed to manipulate microbial activity in the landfill bioreactors to favor methane production by adding ZVMs. This study focuses on evaluating the effects of added ZVM on the leachate generated from replicated lab scale landfill bioreactors. The specific objective was to investigate the effects of ZVMs addition on the organic and inorganic pollutants in leachate. The hypothesis here evaluated was that adding ZVM including ZVI and Zero Valent Manganese (ZVMn) will enhance the removal rates of the organic pollutants present in the leachate, likely by a putative higher rate of microbial metabolism. Test with six (4.23 gallons) bioreactors assembled with MSW collected from the Salt River Landfill and Southwest Regional Landfill showed that under 5 grams /liter of ZVI and 0.625 grams/liter of ZVMn additions, no significant difference was observed in the pH and temperature data of the leachate generated from these reactors. The conductivity data suggested the steady rise across all reactors over the period of time. The removal efficiency of sCOD was highest (27.112 mg/lit/day) for the reactors added with ZVMn at the end of 150 days for bottom layer, however the removal rate was highest (16.955 mg/lit/day) for ZVI after the end of 150 days of the middle layer. Similar trends in the results was observed in TC analysis. HPLC study indicated the dominance of the concentration of heptanoate and isovalerate were leachate generated from the bottom layer across all reactors. Heptanoate continued to dominate in the ZVMn added leachate even after middle layer injection. IC analysis concluded the chloride was dominant in the leachate generated from all the reactors and there was a steady increase in the chloride content over the period of time. Along with chloride, fluoride, bromide, nitrate, nitrite, phosphate and sulfate were also detected in considerable concentrations. In the summary, the addition of the zero valent metals has proved to be efficient in removal of the organics present in the leachate.
ContributorsPandit, Gandhar Abhay (Author) / Cadillo – Quiroz, Hinsby (Thesis advisor) / Olson, Larry (Thesis advisor) / Boyer, Treavor (Committee member) / Arizona State University (Publisher)
Created2019