Matching Items (4)
Filtering by
- Creators: Kitchen, Jennifer
Description
High speed current-steering DACs with high linearity are needed in today's applications such as wired and wireless communications, instrumentation, radar, and other direct digital synthesis (DDS) applications. However, a trade-off exists between the speed and resolution of Nyquist rate current-steering DACs. As the resolution increases, more transistor area is required to meet matching requirements for optimal linearity and thus, the overall speed of the DAC is limited.
In this thesis work, a 12-bit current-steering DAC was designed with current sources scaled below the required matching size to decrease the area and increase the overall speed of the DAC. By scaling the current sources, however, errors due to random mismatch between current sources will arise and additional calibration hardware is necessary to ensure 12-bit linearity. This work presents how to implement a self-calibration DAC that works to fix amplitude errors while maintaining a lower overall area. Additionally, the DAC designed in this thesis investigates the implementation feasibility of a data-interleaved architecture. Data interleaving can increase the total bandwidth of the DACs by 2 with an increase in SQNR by an additional 3 dB.
The final results show that the calibration method can effectively improve the linearity of the DAC. The DAC is able to run up to 400 MSPS frequencies with a 75 dB SFDR performance and above 87 dB SFDR performance at update rates of 200 MSPS.
In this thesis work, a 12-bit current-steering DAC was designed with current sources scaled below the required matching size to decrease the area and increase the overall speed of the DAC. By scaling the current sources, however, errors due to random mismatch between current sources will arise and additional calibration hardware is necessary to ensure 12-bit linearity. This work presents how to implement a self-calibration DAC that works to fix amplitude errors while maintaining a lower overall area. Additionally, the DAC designed in this thesis investigates the implementation feasibility of a data-interleaved architecture. Data interleaving can increase the total bandwidth of the DACs by 2 with an increase in SQNR by an additional 3 dB.
The final results show that the calibration method can effectively improve the linearity of the DAC. The DAC is able to run up to 400 MSPS frequencies with a 75 dB SFDR performance and above 87 dB SFDR performance at update rates of 200 MSPS.
ContributorsJankunas, Benjamin (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2014
Description
Buck converters are a class of switched-mode power converters often used to step down DC input voltages to a lower DC output voltage. These converters naturally produce a current and voltage ripple at their output due to their switching action. Traditional methods of reducing this ripple have involved adding large discrete inductors and capacitors to filter the ripple, but large discrete components cannot be integrated onto chips. As an alternative to using passive filtering components, this project investigates the use of active ripple cancellation to reduce the peak output ripple. Hysteretic controlled buck converters were chosen for their simplicity of design and fast transient response. The proposed cancellation circuits sense the output ripple of the buck converter and inject an equal ripple exactly out of phase with the sensed ripple. Both current-mode and voltage-mode feedback loops are simulated, and the effectiveness of each cancellation circuit is examined. Results show that integrated active ripple cancellation circuits offer a promising substitute for large discrete filters.
ContributorsWang, Ziyan (Author) / Bakkaloglu, Bertan (Thesis director) / Kitchen, Jennifer (Committee member) / Electrical Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2017-12
Description
This thesis outlines the hand-held memory characterization testing system that is to be created into a PCB (printed circuit board). The circuit is designed to apply voltages diagonally through a RRAM cell (32x32 memory array). The purpose of this sweep across the RRAM is to measure and calculate the high and low resistance state value over a specified amount of testing cycles. With each cell having a unique output of high and low resistance states a unique characterization of each RRAM cell is able to be developed. Once the memory is characterized, the specific RRAM cell that was tested is then able to be used in a varying amount of applications for different things based on its uniqueness. Due to an inability to procure a packaged RRAM cell, a Mock-RRAM was instead designed in order to emulate the same behavior found in a RRAM cell.
The final testing circuit and Mock-RRAM are varied and complex but come together to be able to produce a measured value of the high resistance and low resistance state. This is done by the Arduino autonomously digitizing the anode voltage, cathode voltage, and output voltage. A ramp voltage that sweeps from 1V to -1V is applied to the Mock-RRAM acting as an input. This ramp voltage is then later defined as the anode voltage which is just one of the two nodes connected to the Mock-RRAM. The cathode voltage is defined as the other node at which the voltage drops across the Mock-RRAM. Using these three voltages as input to the Arduino, the Mock-RRAM path resistance is able to be calculated at any given point in time. Conducting many test cycles and calculating the high and low resistance values allows for a graph to be developed of the chaotic variation of resistance state values over time. This chaotic variation can then be analyzed further in the future in order to better predict trends and characterize the RRAM cell that was tested.
Furthermore, the interchangeability of many devices on the PCB allows for the testing system to do more in the future. Ports have been added to the final PCB in order to connect a packaged RRAM cell. This will allow for the characterization of a real RRAM memory cell later down the line rather than a Mock-RRAM as emulation. Due to the autonomous testing, very few human intervention is needed which makes this board a great baseline for others in the future looking to add to it and collect larger pools of data.
The final testing circuit and Mock-RRAM are varied and complex but come together to be able to produce a measured value of the high resistance and low resistance state. This is done by the Arduino autonomously digitizing the anode voltage, cathode voltage, and output voltage. A ramp voltage that sweeps from 1V to -1V is applied to the Mock-RRAM acting as an input. This ramp voltage is then later defined as the anode voltage which is just one of the two nodes connected to the Mock-RRAM. The cathode voltage is defined as the other node at which the voltage drops across the Mock-RRAM. Using these three voltages as input to the Arduino, the Mock-RRAM path resistance is able to be calculated at any given point in time. Conducting many test cycles and calculating the high and low resistance values allows for a graph to be developed of the chaotic variation of resistance state values over time. This chaotic variation can then be analyzed further in the future in order to better predict trends and characterize the RRAM cell that was tested.
Furthermore, the interchangeability of many devices on the PCB allows for the testing system to do more in the future. Ports have been added to the final PCB in order to connect a packaged RRAM cell. This will allow for the characterization of a real RRAM memory cell later down the line rather than a Mock-RRAM as emulation. Due to the autonomous testing, very few human intervention is needed which makes this board a great baseline for others in the future looking to add to it and collect larger pools of data.
ContributorsDobrin, Ryan Christopher (Co-author) / Halden, Matthew (Co-author) / Hall, Tanner (Co-author) / Barnaby, Hugh (Thesis director) / Kitchen, Jennifer (Committee member) / Electrical Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2019-05
ContributorsBerry, John (Performer) / Morgan, Lanny (Performer) / Concert Jazz Band (Performer) / ASU Library. Music Library (Publisher)
Created1986-03-05