Matching Items (24)
Filtering by
- All Subjects: Fluid Mechanics
- All Subjects: Gas-turbine disks
- Creators: Huang, Huei-Ping
- Creators: Lee, Taewoo
- Creators: Kostelich, Eric
- Member of: ASU Electronic Theses and Dissertations
- Status: Published
Description
The evolution of single hairpin vortices and multiple interacting hairpin vortices are studied in direct numerical simulations of channel flow at Re-tau=395. The purpose of this study is to observe the effects of increased Reynolds number and varying initial conditions on the growth of hairpins and the conditions under which single hairpins autogenerate hairpin packets. The hairpin vortices are believed to provide a unified picture of wall turbulence and play an important role in the production of Reynolds shear stress which is directly related to turbulent drag. The structures of the initial three-dimensional vortices are extracted from the two-point spatial correlation of the fully turbulent direct numerical simulation of the velocity field by linear stochastic estimation and embedded in a mean flow having the profile of the fully turbulent flow. The Reynolds number of the present simulation is more than twice that of the Re-tau=180 flow from earlier literature and the conditional events used to define the stochastically estimated single vortex initial conditions include a number of new types of events such as quasi-streamwise vorticity and Q4 events. The effects of parameters like strength, asymmetry and position are evaluated and compared with existing results in the literature. This study then attempts to answer questions concerning how vortex mergers produce larger scale structures, a process that may contribute to the growth of length scale with increasing distance from the wall in turbulent wall flows. Multiple vortex interactions are studied in detail.
ContributorsParthasarathy, Praveen Kumar (Author) / Adrian, Ronald (Thesis advisor) / Huang, Huei-Ping (Committee member) / Herrmann, Marcus (Committee member) / Arizona State University (Publisher)
Created2011
Description
Modern day gas turbine designers face the problem of hot mainstream gas ingestion into rotor-stator disk cavities. To counter this ingestion, seals are installed on the rotor and stator disk rims and purge air, bled off from the compressor, is injected into the cavities. It is desirable to reduce the supply of purge air as this decreases the net power output as well as efficiency of the gas turbine. Since the purge air influences the disk cavity flow field and effectively the amount of ingestion, the aim of this work was to study the cavity velocity field experimentally using Particle Image Velocimetry (PIV). Experiments were carried out in a model single-stage axial flow turbine set-up that featured blades as well as vanes, with purge air supplied at the hub of the rotor-stator disk cavity. Along with the rotor and stator rim seals, an inner labyrinth seal was provided which split the disk cavity into a rim cavity and an inner cavity. First, static gage pressure distribution was measured to ensure that nominally steady flow conditions had been achieved. The PIV experiments were then performed to map the velocity field on the radial-tangential plane within the rim cavity at four axial locations. Instantaneous velocity maps obtained by PIV were analyzed sector-by-sector to understand the rim cavity flow field. It was observed that the tangential velocity dominated the cavity flow at low purge air flow rate, its dominance decreasing with increase in the purge air flow rate. Radially inboard of the rim cavity, negative radial velocity near the stator surface and positive radial velocity near the rotor surface indicated the presence of a recirculation region in the cavity whose radial extent increased with increase in the purge air flow rate. Qualitative flow streamline patterns are plotted within the rim cavity for different experimental conditions by combining the PIV map information with ingestion measurements within the cavity as reported in Thiagarajan (2013).
ContributorsPathak, Parag (Author) / Roy, Ramendra P (Thesis advisor) / Calhoun, Ronald (Committee member) / Lee, Taewoo (Committee member) / Arizona State University (Publisher)
Created2013
Description
A major concern in the operation of present-day gas turbine engines is the ingestion of hot mainstream gas into rotor-stator disk cavities of the high-pressure turbine stages. Although the engines require high gas temperature at turbine entry for good performance efficiency, the ingested gas shortens the lives of the cavity internals, particularly that of the rotor disks. Steps such as installing seals at the disk rims and injecting purge (secondary) air bled from the compressor discharge into the cavities are implemented to reduce the gas ingestion. Although there are advantages to the above-mentioned steps, the performance of a gas turbine engine is diminished by the purge air bleed-off. This then requires that the cavity sealing function be achieved with as low a purge air supply rate as possible. This, in turn, renders imperative an in-depth understanding of the pressure and velocity fields in the main gas path and within the disk cavities. In this work, experiments were carried out in a model 1.5-stage (stator-rotor-stator) axial air turbine to study the ingestion of main air into the aft, rotor-stator, disk cavity. The cavity featured rotor and stator rim seals with radial clearance and axial overlap and an inner labyrinth seal. First, time-average static pressure distribution was measured in the main gas path upstream and downstream of the rotor as well as in the cavity to ensure that a nominally steady run condition had been achieved. Main gas ingestion was determined by measuring the concentration distribution of tracer gas (CO2) in the cavity. To map the cavity fluid velocity field, particle image velocimetry was employed. Results are reported for two main air flow rates, two rotor speeds, and four purge air flow rates.
ContributorsJunnarkar, Nihal (Author) / Roy, Ramendra P (Thesis advisor) / Mignolet, Marc (Committee member) / Lee, Taewoo (Committee member) / Arizona State University (Publisher)
Created2010
Description
Efficient performance of gas turbines depends, among several parameters, on the mainstream gas entry temperature. At the same time, transport of this high temperature gas into the rotor-stator cavities of turbine stages affects the durability of rotor disks. This transport is usually countered by installing seals on the rotor and stator disk rims and by pressurizing the cavities by injecting air (purge gas) bled from the compressor discharge. The configuration of the rim seals influences the magnitude of main gas ingestion as well as the interaction of the purge gas with the main gas. The latter has aerodynamic and hub endwall heat transfer implications in the main gas path. In the present work, experiments were performed on model single-stage and 1.5-stage axial-flow turbines. The turbines featured vanes, blades, and rim seals on both the rotor and stator disks. Three different rim seal geometries, viz., axially overlapping radial clearance rim seals for the single-stage turbine cavity and the 1.5-stage turbine aft cavity, and a rim seal with angular clearance for the single-stage turbine cavity were studied. In the single-stage turbine, an inner seal radially inboard in the cavity was also provided; this effectively divided the disk cavity into a rim cavity and an inner cavity. For the aft rotor-stator cavity of the 1.5-stage turbine, a labyrinth seal was provided radially inboard, again creating a rim cavity and an inner cavity. Measurement results of time-average main gas ingestion into the cavities using tracer gas (CO2), and ensemble-averaged trajectories of the purge gas flowing out through the rim seal gap into the main gas path using particle image velocimetry are presented. For both turbines, significant ingestion occurred only in the rim cavity. The inner cavity was almost completely sealed by the inner seal, at all purge gas flow rates for the single-stage turbine and at the higher purge gas flow rates for 1.5-stage turbine. Purge gas egress trajectory was found to depend on main gas and purge gas flow rates, the rim seal configuration, and the azimuthal location of the trajectory mapping plane with respect to the vanes.
ContributorsBalasubramanian, Jagdish Harihara (Author) / Roy, Ramendra P (Thesis advisor) / Lee, Taewoo (Committee member) / Phelan, Patrick (Committee member) / Arizona State University (Publisher)
Created2010
Description
Ingestion of high temperature mainstream gas into the rotor-stator cavities of a gas turbine is one of the major problems faced by the turbine designers. The ingested gas heats up rotor disks and induces higher thermal stresses on them, giving rise to durability concern. Ingestion is usually reduced by installing seals on the rotor and stator rims and by purging the disk cavity by secondary air bled from the compressor discharge. The geometry of the rim seals and the secondary air flow rate, together, influence the amount of gas that gets ingested into the cavities. Since the amount of secondary air bled off has a negative effect on the gas turbine thermal efficiency, one goal is to use the least possible amount of secondary air. This requires a good understanding of the flow and ingestion fields within a disk cavity. In the present study, the mainstream gas ingestion phenomenon has been experimentally studied in a model single-stage axial flow gas turbine. The turbine stage featured vanes and blades, and rim seals on both the rotor and stator. Additionally, the disk cavity contained a labyrinth seal radially inboard which effectively divided the cavity into a rim cavity and an inner cavity. Time-average static pressure measurements were obtained at various radial positions within the disk cavity, and in the mainstream gas path at three axial locations at the outer shroud spread circumferentially over two vane pitches. The time-average static pressure in the main gas path exhibited a periodic asymmetry following the vane pitch whose amplitude diminished with increasing distance from the vane trailing edge. The static pressure distribution increased with the secondary air flow rate within the inner cavity but was found to be almost independent of it in the rim cavity. Tracer gas (CO2) concentration measurements were conducted to determine the sealing effectiveness of the rim seals against main gas ingestion. For the rim cavity, the sealing effectiveness increased with the secondary air flow rate. Within the inner cavity however, this trend reversed -this may have been due to the presence of rotating low-pressure flow structures inboard of the labyrinth seal.
ContributorsThiagarajan, Jayanth kumar (Author) / Roy, Ramendra P (Thesis advisor) / Lee, Taewoo (Committee member) / Mignolet, Marc (Committee member) / Arizona State University (Publisher)
Created2013
Description
Rooftop photovoltaic (PV) systems are becoming increasingly common as the efficiency of solar panels increase, the cost decreases, and worries about climate change increase and become increasingly prevalent. An under explored aspect of rooftop solar systems is the thermal effects that the systems have on the local area. These effects are investigated in this paper to determine the overall impact that solar systems have on the heating and cooling demands of a building as well as on the efficiency losses of the solar panels due to the increased temperature on the panels themselves. The specific building studied in this paper is the Goldwater Center for Science and Engineering located in the Tempe campus of Arizona State University. The ambient conditions were modeled from a typical July day in Tempe. A numerical model of a simple flat roof was also created to find the average rooftop temperature throughout the day. Through this study it was determined that solar panels cause a decrease in the maximum temperature of the rooftop during the day, while reducing the ability of the roof to be cooled during the night. The solar panels also saw a high temperature during the day during the most productive time of day for solar panels, which saw a decrease in total energy production for the panels.
ContributorsNaber, Nicholas (Author) / Huang, Huei-Ping (Thesis advisor) / Phelan, Patrick (Committee member) / Bocanegra, Luis (Committee member) / Arizona State University (Publisher)
Created2022
Description
Computing the fluid phase interfaces in multiphase flow is a challenging area of research in fluids. The Volume of Fluid andLevel Set methods are a few algorithms that have been developed for reconstructing the multiphase fluid flow interfaces.
The thesis work focuses on exploring the ability of neural networks to reconstruct the multiphase fluid flow interfaces using
a data-driven approach.
The neural network model has liquid volume fraction stencils as an input, and it predicts the radius of the circle as an
output of the network which represents a phase interface separating two immiscible fluids inside a fluid domain. The liquid
volume fraction stencils are generated for randomly varying circle radii within a 1x1 domain using an open-source VOFI
library. These datasets are used to train the neural network. Once the model is trained, the predicted circular phase
interface from the neural network output is used to generate back the predicted liquid volume fraction stencils.
Error norms values are calculated to assess the error in the neural network model’s predicted liquid volume fraction
stencils with the actual liquid volume fraction stencils from the VOFI library. The neural network parameters are optimized
by testing them for different hyper-parameters to reduce the error norms. So as to minimize the difference between the
predicted and the actual liquid volume fraction stencils and errors in reconstructing the fluid phase interface geometry.
ContributorsPawar, Pranav Rajesh (Author) / Herrmann, Marcus (Thesis advisor) / Zhuang, Houlong (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2023
Description
Theoretical analyses of liquid atomization (bulk to droplet conversion) and turbulence have potential to advance the computability of these flows. Instead of relying on full computations or models, fundamental conservation equations can be manipulated to generate partial or full solutions. For example, integral form of the mass and energy for spray flows leads to an explicit relationship between the drop size and liquid velocities. This is an ideal form to integrate with existing computational fluid dynamic (CFD), which is well developed to solve for the liquid velocities, i.e., the momentum equation(s). Theoretical adaption to CFD has been performed for various injection geometries, with results that compare quite well with experimental data. Since the drop size is provided analytically, computational time/cost for simulating spray flows with liquid atomization is no more than single-phase flows. Some advances have also been made on turbulent flows, by using a new set of perspectives on transport, scaling and energy distributions. Conservation equations for turbulence momentum and kinetic energy have been derived in a coordinate frame moving with the local mean velocities, which produce the Reynolds stress components, without modeling. Scaling of the Reynolds stress is also found at the first- and second-gradient levels. Finally, maximum-entropy principle has been used to derive the energy spectra in turbulent flows.
ContributorsPark, Jung Eun (Author) / Lee, Taewoo (Thesis advisor) / Gardner, Carl (Committee member) / Huang, Huei-Ping (Committee member) / Kim, Jeonglae (Committee member) / Chen, Kangping (Committee member) / Arizona State University (Publisher)
Created2022
Description
The propulsion matrix provides a compact description of the locomotion of a single flagella molecular motor in a low Reynolds number environment. The locomotion properties of individual flagellar motors are central to bacterial behavior, including chemotaxis, pathogenesis, and biofilm formation. However, because conventional hydrodynamic measurement approaches require applied forces, torques, or fluid flows, it is not possible to directly measure the propulsion matrix for an individual microscale helical filament. Here, the limitations inherent to conventional measurement approaches are overcome using a combination of theoretical, experimental, and computational advancements. First, the relationship between the elements of the propulsion matrix with translational and rotational Brownian motion is derived using the fluctuation-dissipation theorem. Next, a volumetric fluorescent imaging using high resolution oblique plane microscopy with sufficient spatio-temporal resolution is conducted to resolve both translation and rotation of individual helical filaments isolated from E.coli's flagellar motor. Finally, a computational framework is developed to track individual helical filaments across six degrees of freedom, extract diffusion coefficients, and quantify the temporal correlation between translation and rotation. This study computed the maximum propulsion efficiency to be around 1.7%. Direct measurement of propulsion efficiency generally agrees with the ensemble and large-scale measurements previously performed using conventional hydrodynamic measurements. The findings suggest that the approach described here can be extended to more complex in-vitro experiments that evaluate microscale molecular motors. For example, evaluating sperm motility without inducing chemotaxis or utilizing a microfluidic setup.
ContributorsDjutanta, Franky (Author) / Hariadi, Rizal (Thesis advisor) / Wang, Robert (Thesis advisor) / Yurke, Bernard (Committee member) / Herrmann, Marcus (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2022
Description
This thesis focuses on the turbulent bluff body wakes in incompressible and compressible flows. An incompressible wake flow past an axisymmetric body of revolution at a diameter-based Reynolds number Re=5000 is investigated via a direct numerical simulation. It is followed by the development of a compressible solver using a split-form discontinuous Galerkin spectral element method framework with shock capturing. In the study on incompressible wake flows, three dominant coherent vortical motions are identified in the wake: the vortex shedding motion with the frequency of St=0.27, the bubble pumping motion with St=0.02, and the very-low-frequency (VLF) motion originated in the very near wake of the body with the frequencies St=0.002 and 0.005. The very-low-frequency motion is associated with a slow precession of the wake barycenter. The vortex shedding pattern is demonstrated to follow a reflectional symmetry breaking mode, with the detachment location rotating continuously and making a full circle over one vortex shedding period. The VLF radial motion with St=0.005 originates as m = 1 mode, but later transitions into m = 2 mode in the intermediate wake. Proper orthogonaldecomposition (POD) and dynamic mode decomposition (DMD) are further performed to analyze the spatial structure associated with the dominant coherent motions. Results of the POD and DMD analysis are consistent with the results of the azimuthal Fourier analysis. To extend the current incompressible code to be able to solve compressible flows, a computational methodology is developed using a high-order approximation for the compressible Navier-Stokes equations with discontinuities. The methodology is based on a split discretization framework with a summation-by-part operator. An entropy viscosity method and a subcell finite volume method are implemented to capture discontinuities. The developed high-order split-form with shock-capturing methodology is subject to a series of evaluation on cases from subsonic to hypersonic, from one-dimensional to three dimensional. The Taylor-Green vortex case and the supersonic sphere wake case show the capability to handle three-dimensional turbulent flows without and with the presence of shocks. It is also shown that higher-order approximations yield smaller errors than lower-order approximations, for the same number of total degrees of freedom.
ContributorsZhang, Fengrui (Author) / Peet, Yulia (Thesis advisor) / Kostelich, Eric (Committee member) / Kim, Jeonglae (Committee member) / Hermann, Marcus (Committee member) / Adrian, Ronald (Committee member) / Arizona State University (Publisher)
Created2022