Matching Items (7)
Filtering by
- All Subjects: RRAM
- Creators: Electrical Engineering Program
- Resource Type: Text
- Status: Published
Description
Resistive Random Access Memory (RRAM) is an emerging type of non-volatile memory technology that seeks to replace FLASH memory. The RRAM crossbar array is advantageous in its relatively small cell area and faster read latency in comparison to NAND and NOR FLASH memory; however, the crossbar array faces design challenges of its own in sneak-path currents that prevent proper reading of memory stored in the RRAM cell. The Current Sensing Amplifier is one method of reading RRAM crossbar arrays. HSpice simulations are used to find the associated reading delays of the Current Sensing Amplifier with respect to various sizes of RRAM crossbar arrays, as well as the largest array size compatible for accurate reading. It is found that up to 1024x1024 arrays are achievable with a worst-case read delay of 815ps, and it is further likely 2048x2048 arrays are able to be read using the Current Sensing Amplifier. In comparing the Current Sensing Amplifier latency results with previously obtained latency results from the Voltage Sensing Amplifier, it is shown that the Voltage Sensing Amplifier reads arrays in sizes up to 256x256 faster while the Current Sensing Amplifier reads larger arrays faster.
ContributorsMoore, Jenna Barber (Author) / Yu, Shimeng (Thesis director) / Liu, Rui (Committee member) / Electrical Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-12
Description
This thesis outlines the hand-held memory characterization testing system that is to be created into a PCB (printed circuit board). The circuit is designed to apply voltages diagonally through a RRAM cell (32x32 memory array). The purpose of this sweep across the RRAM is to measure and calculate the high and low resistance state value over a specified amount of testing cycles. With each cell having a unique output of high and low resistance states a unique characterization of each RRAM cell is able to be developed. Once the memory is characterized, the specific RRAM cell that was tested is then able to be used in a varying amount of applications for different things based on its uniqueness. Due to an inability to procure a packaged RRAM cell, a Mock-RRAM was instead designed in order to emulate the same behavior found in a RRAM cell.
The final testing circuit and Mock-RRAM are varied and complex but come together to be able to produce a measured value of the high resistance and low resistance state. This is done by the Arduino autonomously digitizing the anode voltage, cathode voltage, and output voltage. A ramp voltage that sweeps from 1V to -1V is applied to the Mock-RRAM acting as an input. This ramp voltage is then later defined as the anode voltage which is just one of the two nodes connected to the Mock-RRAM. The cathode voltage is defined as the other node at which the voltage drops across the Mock-RRAM. Using these three voltages as input to the Arduino, the Mock-RRAM path resistance is able to be calculated at any given point in time. Conducting many test cycles and calculating the high and low resistance values allows for a graph to be developed of the chaotic variation of resistance state values over time. This chaotic variation can then be analyzed further in the future in order to better predict trends and characterize the RRAM cell that was tested.
Furthermore, the interchangeability of many devices on the PCB allows for the testing system to do more in the future. Ports have been added to the final PCB in order to connect a packaged RRAM cell. This will allow for the characterization of a real RRAM memory cell later down the line rather than a Mock-RRAM as emulation. Due to the autonomous testing, very few human intervention is needed which makes this board a great baseline for others in the future looking to add to it and collect larger pools of data.
The final testing circuit and Mock-RRAM are varied and complex but come together to be able to produce a measured value of the high resistance and low resistance state. This is done by the Arduino autonomously digitizing the anode voltage, cathode voltage, and output voltage. A ramp voltage that sweeps from 1V to -1V is applied to the Mock-RRAM acting as an input. This ramp voltage is then later defined as the anode voltage which is just one of the two nodes connected to the Mock-RRAM. The cathode voltage is defined as the other node at which the voltage drops across the Mock-RRAM. Using these three voltages as input to the Arduino, the Mock-RRAM path resistance is able to be calculated at any given point in time. Conducting many test cycles and calculating the high and low resistance values allows for a graph to be developed of the chaotic variation of resistance state values over time. This chaotic variation can then be analyzed further in the future in order to better predict trends and characterize the RRAM cell that was tested.
Furthermore, the interchangeability of many devices on the PCB allows for the testing system to do more in the future. Ports have been added to the final PCB in order to connect a packaged RRAM cell. This will allow for the characterization of a real RRAM memory cell later down the line rather than a Mock-RRAM as emulation. Due to the autonomous testing, very few human intervention is needed which makes this board a great baseline for others in the future looking to add to it and collect larger pools of data.
ContributorsDobrin, Ryan Christopher (Co-author) / Halden, Matthew (Co-author) / Hall, Tanner (Co-author) / Barnaby, Hugh (Thesis director) / Kitchen, Jennifer (Committee member) / Electrical Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2019-05
Description
Imaging using electric fields could provide a cheaper, safer, and easier alternative to the standard methods used for imaging. The viability of electric field imaging at very low frequencies using D-dot sensors has already been investigated and proven. The new goal is to determine if imaging is viable at high frequencies. In order to accomplish this, the operational amplifiers used in the very low frequency imaging test set up must be replaced with ones that have higher bandwidth. The trade-off of using these amplifiers is that they have a typical higher input leakage current on the order of 100 compared to the standard. Using a modified circuit design technique that reduces input leakage current of the operational amplifiers used in the imaging test setup, a printed circuit board with D-dot sensors is fabricated to identify the frequency limitations of electric field imaging. Data is collected at both low and high frequencies as well as low peak voltage. The data is then analyzed to determine the range in intensity of electric field and frequency that this circuit low-leakage design can accurately detect a signal. Data is also collected using another printed circuit board that uses the standard circuit design technique. The data taken from the different boards is compared to identify if the modified circuit design technique allows for higher sensitivity imaging. In conclusion, this research supports that using low-leakage design techniques can allow for signal detection comparable to that of the standard circuit design. The low-leakage design allowed for sensitivity within a factor two to that of the standard design. Although testing at higher frequencies was limited, signal detection for the low-leakage design was reliable up until 97 kHz, but further experimentation is needed to determine the upper frequency limits.
ContributorsLin, Richard (Co-author) / Angell, Tyler (Co-author) / Allee, David (Thesis director) / Chung, Hugh (Committee member) / Electrical Engineering Program (Contributor) / W. P. Carey School of Business (Contributor) / Barrett, The Honors College (Contributor)
Created2016-12
Description
RRAM is an emerging technology that looks to replace FLASH NOR and possibly NAND memory. It is attractive because it uses an adjustable resistance and does not rely on charge; in the sub-10nm feature size circuitry this is critical. However, RRAM cross-point arrays suffer tremendously from leakage currents that prevent proper readings in larger array sizes. In this research an exponential IV selector was added to each cell to minimize this current. Using this technique the largest array-size supportable was determined to be 512x512 cells using the conventional voltage sense amplifier by HSPICE simulations. However, with the increase in array size, the sensing latency also remarkably increases due to more sneak path currents, approaching 873 ns for the 512x512 array.
ContributorsMadler, Ryan Anton (Author) / Yu, Shimeng (Thesis director) / Cao, Yu (Committee member) / Electrical Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description
Readout Integrated Circuits(ROICs) are important components of infrared(IR) imag
ing systems. Performance of ROICs affect the quality of images obtained from IR
imaging systems. Contemporary infrared imaging applications demand ROICs that
can support large dynamic range, high frame rate, high output data rate, at low
cost, size and power. Some of these applications are military surveillance, remote
sensing in space and earth science missions and medical diagnosis. This work focuses
on developing a ROIC unit cell prototype for National Aeronautics and Space Ad
ministration(NASA), Jet Propulsion Laboratory’s(JPL’s) space applications. These
space applications also demand high sensitivity, longer integration times(large well
capacity), wide operating temperature range, wide input current range and immunity
to radiation events such as Single Event Latchup(SEL).
This work proposes a digital ROIC(DROIC) unit cell prototype of 30ux30u size,
to be used mainly with NASA JPL’s High Operating Temperature Barrier Infrared
Detectors(HOT BIRDs). Current state of the art DROICs achieve a dynamic range
of 16 bits using advanced 65-90nm CMOS processes which adds a lot of cost overhead.
The DROIC pixel proposed in this work uses a low cost 180nm CMOS process and
supports a dynamic range of 20 bits operating at a low frame rate of 100 frames per
second(fps), and a dynamic range of 12 bits operating at a high frame rate of 5kfps.
The total electron well capacity of this DROIC pixel is 1.27 billion electrons, enabling
integration times as long as 10ms, to achieve better dynamic range. The DROIC unit
cell uses an in-pixel 12-bit coarse ADC and an external 8-bit DAC based fine ADC.
The proposed DROIC uses layout techniques that make it immune to radiation up to
300krad(Si) of total ionizing dose(TID) and single event latch-up(SEL). It also has a
wide input current range from 10pA to 1uA and supports detectors operating from
Short-wave infrared (SWIR) to longwave infrared (LWIR) regions.
ing systems. Performance of ROICs affect the quality of images obtained from IR
imaging systems. Contemporary infrared imaging applications demand ROICs that
can support large dynamic range, high frame rate, high output data rate, at low
cost, size and power. Some of these applications are military surveillance, remote
sensing in space and earth science missions and medical diagnosis. This work focuses
on developing a ROIC unit cell prototype for National Aeronautics and Space Ad
ministration(NASA), Jet Propulsion Laboratory’s(JPL’s) space applications. These
space applications also demand high sensitivity, longer integration times(large well
capacity), wide operating temperature range, wide input current range and immunity
to radiation events such as Single Event Latchup(SEL).
This work proposes a digital ROIC(DROIC) unit cell prototype of 30ux30u size,
to be used mainly with NASA JPL’s High Operating Temperature Barrier Infrared
Detectors(HOT BIRDs). Current state of the art DROICs achieve a dynamic range
of 16 bits using advanced 65-90nm CMOS processes which adds a lot of cost overhead.
The DROIC pixel proposed in this work uses a low cost 180nm CMOS process and
supports a dynamic range of 20 bits operating at a low frame rate of 100 frames per
second(fps), and a dynamic range of 12 bits operating at a high frame rate of 5kfps.
The total electron well capacity of this DROIC pixel is 1.27 billion electrons, enabling
integration times as long as 10ms, to achieve better dynamic range. The DROIC unit
cell uses an in-pixel 12-bit coarse ADC and an external 8-bit DAC based fine ADC.
The proposed DROIC uses layout techniques that make it immune to radiation up to
300krad(Si) of total ionizing dose(TID) and single event latch-up(SEL). It also has a
wide input current range from 10pA to 1uA and supports detectors operating from
Short-wave infrared (SWIR) to longwave infrared (LWIR) regions.
ContributorsPraveen, Subramanya Chilukuri (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Long, Yu (Committee member) / Arizona State University (Publisher)
Created2019
Description
The NASA Psyche Iron Meteorite Imaging System (IMIS) is a standalone system created to image metal meteorites from ASU’s Center for Meteorite Studies’ collection that have an etched surface. Meteorite scientists have difficulty obtaining true-to-life images of meteorites through traditional photography methods due to the meteorites’ shiny, irregular surfaces, which interferes with their ability to identify meteorites’ component materials through image analysis. Using the IMIS, scientists can easily and consistently obtain glare-free photographs of meteorite surface that are suitable for future use in an artificial intelligence-based meteorite component analysis system. The IMIS integrates a lighting system, a mounted camera, a sample positioning area, a meteorite leveling/positioning system, and a touch screen control panel featuring an interface that allows the user to see a preview of the image to be taken as well as an edge detection view, a glare detection view, a button that allows the user to remotely take the picture, and feedback if very high levels of glare are detected that may indicate a camera or positioning error. Initial research and design work were completed by the end of Fall semester, and Spring semester consisted of building and testing the system. The current system is fully functional, and photos taken by the current system have been approved by a meteorite expert and an AI expert. The funding for this project was tentatively capped at $1000 for miscellaneous expenses, not including a camera to be supplied by the School of Earth and Space Exploration. When SESE was unable to provide a camera, an additional $4000 were allotted for camera expenses. So far, $1935 of the total $5000 budget has been spent on the project, putting the project $3065 under budget. While this system is a functional prototype, future capstone projects may involve the help of industrial designers to improve the technician’s experience through automating the sample positioning process.
ContributorsBaerwaldt, Morgan Kathleen (Author) / Bowman, Cassie (Thesis director) / Kozicki, Michael (Committee member) / School of Art (Contributor) / Electrical Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2019-05
Description
Most machine learning algorithms, and specifically neural networks, utilize vector-matrix multiplication (VMM) to process information, but these calculations are CPU intensive and can have long run-times. This issue is fundamentally outlined by the von Neumann bottleneck. Because of this undesirable expense associated with performing VMM via software, the exploration of new ways to perform the same calculations via hardware have grown more popular. When performed with hardware that is specialized to perform these calculations, VMM becomes far more power-efficient and less time consuming. This project expands upon those principles and seeks to validate the use of RRAM in this hardware.
The flexibility of the conductance of RRAM makes these devices a strong contender for hardware-driven VMM calculation for neural network computing. The conductance of these devices is affected by the pulse width of a voltage signal sent across the devices at each node. This pulse is produced on-chip and can be modified by user inputs. The design of this pulse- producing circuit, as well as the simulated and physical functionality of the design, is discussed in this Honors Thesis.
Simulation and physical testing of the pulse-producing design on the ASIC have verified correct operation of the design. This operation is imperative to the future ability of the ASIC to perform accurate VMM.
ContributorsPearson, Katherine (Author) / Barnaby, Hugh (Thesis director) / Wilson, Donald (Committee member) / Barrett, The Honors College (Contributor) / Electrical Engineering Program (Contributor) / School of International Letters and Cultures (Contributor)
Created2022-05