Matching Items (4)
Filtering by

Clear all filters

156317-Thumbnail Image.png

Utilization of thermoplastic mounting studs for simple performance testing on hot mix asphalt

Description

The objective of the research is to test the use of 3D printed thermoplastic to produce fixtures which affix instrumentation to asphalt concrete samples used for Simple Performance Testing (SPT). The testing is done as part of materials characterization to obtain properties that will help in future pavement designs. Currently,…

The objective of the research is to test the use of 3D printed thermoplastic to produce fixtures which affix instrumentation to asphalt concrete samples used for Simple Performance Testing (SPT). The testing is done as part of materials characterization to obtain properties that will help in future pavement designs. Currently, these fixtures (mounting studs) are made of expensive brass and cumbersome to clean with or without chemicals.

Three types of thermoplastics were utilized to assess the effect of temperature and applied stress on the performance of the 3D printed studs. Asphalt concrete samples fitted with thermoplastic studs were tested according to AASHTO & ASTM standards. The thermoplastics tested are: Polylactic acid (PLA), the most common 3D printing material; Acrylonitrile Butadiene Styrene (ABS), a typical 3D printing material which is less rigid than PLA and has a higher melting temperature; Polycarbonate (PC), a strong, high temperature 3D printing material.

A high traffic volume Marshal mix design from the City of Phoenix was obtained and adapted to a Superpave mix design methodology. The mix design is dense-graded with nominal maximum aggregate size of ¾” inch and a PG 70-10 binder. Samples were fabricated and the following tests were performed: Dynamic Modulus |E*| conducted at five temperatures and six frequencies; Flow Number conducted at a high temperature of 50°C, and axial cyclic fatigue test at a moderate temperature of 18°C.

The results from SPT for each 3D printed material were compared to results using brass mounting studs. Validation or rejection of the concept was determined from statistical analysis on the mean and variance of collected SPT test data.

The concept of using 3D printed thermoplastic for mounting stud fabrication is a promising option; however, the concept should be verified with more extensive research using a variety of asphalt mixes and operators to ensure no bias in the repeatability and reproducibility of test results. The Polycarbonate (PC) had a stronger layer bonding than ABS and PLA while printing. It was recommended for follow up studies.
ContributorsBeGell, Dirk (Author) / Kaloush, Kamil (Thesis advisor) / Mamlouk, Michael (Committee member) / Stempihar, Jeffery (Committee member) / Arizona State University (Publisher)
Created2018

A study of heating and degradation of acrylonitrile-butadiene-styrene/polycarbonate polymer due to ultraviolet lasers illumination during localized pre-deposition heating for fused filament fabrication 3D printing

Description
With the growing popularity of 3d printing in recreational, research, and commercial enterprises new techniques and processes are being developed to improve the quality of parts created. Even so, the anisotropic properties is still a major hindrance of parts manufactured in this method. The goal is to produce parts that…

With the growing popularity of 3d printing in recreational, research, and commercial enterprises new techniques and processes are being developed to improve the quality of parts created. Even so, the anisotropic properties is still a major hindrance of parts manufactured in this method. The goal is to produce parts that mimic the strength characteristics of a comparable part of the same design and materials created using injection molding. In achieving this goal the production cost can be reduced by eliminating the initial investment needed for the creation of expensive tooling. This initial investment reduction will allow for a wider variant of products in smaller batch runs to be made available. This thesis implements the use of ultraviolet (UV) illumination for an in-process laser local pre-deposition heating (LLPH). By comparing samples with and without the LLPH process it is determined that applied energy that is absorbed by the polymer is converted to an increase in the interlayer temperature, and resulting in an observed increase in tensile strength over the baseline test samples. The increase in interlayer bonding thus can be considered the dominating factor over polymer degradation.
ContributorsKusel, Scott Daniel (Author) / Hsu, Keng (Thesis advisor) / Sodemann, Angela (Committee member) / Kannan, Arunachala M (Committee member) / Arizona State University (Publisher)
Created2017
171360-Thumbnail Image.png

3D printed Bioactive Scaffolds for Tissue Repair and Drug Delivery

Description
Combining 3D bio-printing and drug delivery are promising techniques tofabricate scaffolds with well controlled and patient-specific structures for tissue engineering. In this study, silk derivatives of bioink were developed consisting of silk fibroin and gelatin then 3D printed into scaffolds. The scaffolds would be evaluated for small molecule release, cell growth, degradation, and…

Combining 3D bio-printing and drug delivery are promising techniques tofabricate scaffolds with well controlled and patient-specific structures for tissue engineering. In this study, silk derivatives of bioink were developed consisting of silk fibroin and gelatin then 3D printed into scaffolds. The scaffolds would be evaluated for small molecule release, cell growth, degradation, and morphology. Preparations and design of the scaffolds are major parts of engineering and tissue engineering. Scaffolds are designed to mimic extracellular matrix by providing structural support as well as promoting cell attachment and proliferation with minimum inflammation while degrading at a controlled rate. Scaffolds offers new potentials in medicine by aiding in the preparation of personalized and controlled release therapeutic systems.
ContributorsNg, Johnny (Author) / Rege, Kaushal (Thesis advisor) / Holloway, Julianne (Committee member) / Jin, Kailong (Committee member) / Arizona State University (Publisher)
Created2022
190908-Thumbnail Image.png

Explore Rapid 3D Printing of Magnetically Actuated Microstructures Via Micro-Continuous Liquid Interface Production

Description
Advancements in three-dimensional (3D) additive manufacturing techniques have opened up new possibilities for healthcare systems and the medical industry, allowing for the realization of concepts that were once confined to theoretical discussions. Among these groundbreaking research endeavors is the development of intricate magnetic structures that can be actuated through non-invasive…

Advancements in three-dimensional (3D) additive manufacturing techniques have opened up new possibilities for healthcare systems and the medical industry, allowing for the realization of concepts that were once confined to theoretical discussions. Among these groundbreaking research endeavors is the development of intricate magnetic structures that can be actuated through non-invasive methods, including electromagnetic and magnetic actuation. Magnetic actuation, in particular, offers the advantage of untethered operation. In this study, a photopolymerizable resin infused with Fe3O4 oxide nanoparticles is employed in the printing process using the micro-continuous liquid interface production technique. The objective is to optimize the manufacturing process to produce microstructures featuring smooth surfaces and reduced surface porosity, and enhanced flexibility and magnetic actuation. Various intricate structures are fabricated to validate the printing process's capabilities. Furthermore, the assessment of the flexibilty of these 3D-printed structures is conducted in the presence of an external magnetic field using a homemade bending test setup, allowing for a comprehensive characterization of these components. This research serves as a foundation for the future design and development of micro-robots using micro-continuous liquid interface production technique.
ContributorsJha, Ujjawal (Author) / Chen, Xiangfan (Thesis advisor) / Li, Xiangjia (Committee member) / Jin, Kailong (Committee member) / Nian, Qiong (Committee member) / Arizona State University (Publisher)
Created2023