Matching Items (19)
Filtering by
- All Subjects: Aerospace Engineering
- Creators: Takahashi, Timothy
- Member of: Theses and Dissertations
Description
This thesis seeks to further explore off-design point operation of gas turbines and to examine the capabilities of GasTurb 12 as a tool for off-design analysis. It is a continuation of previous thesis work which initially explored the capabilities of GasTurb 12. The research is conducted in order to: 1) validate GasTurb 12 and, 2) predict off-design performance of the Garrett GTCP85-98D located at the Arizona State University Tempe campus. GasTurb 12 is validated as an off-design point tool by using the program to predict performance of an LM2500+ marine gas turbine. Haglind and Elmegaard (2009) published a paper detailing a second off-design point method and it includes the manufacturer's off-design point data for the LM2500+. GasTurb 12 is used to predict off-design point performance of the LM2500+ and compared to the manufacturer's data. The GasTurb 12 predictions show good correlation. Garrett has published specification data for the GTCP85-98D. This specification data is analyzed to determine the design point and to comment on off-design trends. Arizona State University GTCP85-98D off-design experimental data is evaluated. Trends presented in the data are commented on and explained. The trends match the expected behavior demonstrated in the specification data for the same gas turbine system. It was originally intended that a model of the GTCP85-98D be constructed in GasTurb 12 and used to predict off-design performance. The prediction would be compared to collected experimental data. This is not possible because the free version of GasTurb 12 used in this research does not have a module to model a single spool turboshaft. This module needs to be purchased for this analysis.
ContributorsMartinjako, Jeremy (Author) / Trimble, Steve (Thesis advisor) / Dahm, Werner (Committee member) / Middleton, James (Committee member) / Arizona State University (Publisher)
Created2014
Description
Recent literature indicates potential benefits in microchannel cooling if an inlet orifice is used to suppress pressure oscillations that develop under two-phase conditions. This study investigates the costs and benefits of using an adjustable microchannel inlet orifice. The focus is on orifice effect during steady-state boiling and critical heat flux (CHF) in the channels using R134a in a pumped refrigerant loop (PRL). To change orifice size, a dam controlled with a micrometer was placed in front of 31 parallel microchannels. Each channel had a hydraulic diameter of 0.235 mm and a length of 1.33 cm. For steady state two-phase conditions, mass fluxes of 300 kg m-2 s-1 and 600 kg m-2 s-1were investigated. For orifice sizes with a hydraulic diameter to unrestricted hydraulic diameter (Dh:Dh,ur) ratio less than 35 percent, oscillations were reduced and wall temperatures fell up to 1.5 °C. Critical heat flux data were obtained for 7 orifice sizes with mass fluxes from 186 kg m-2 s-1 to 847 kg m-2 s-1. For all mass fluxes and inlet conditions tested, CHF values for a Dh:Dh,ur ratio of 1.8 percent became increasingly lower (up to 37 W cm-2 less) than those obtained with larger orifices. An optimum orifice size with Dh:Dh,ur of 35 percent emerged, offering up to 5 W cm-2 increase in CHF over unrestricted conditions at the highest mass flux tested, 847 kg m-2 s-1. These improvements in cooling ability with inlet orifices in place under both steady-state and impending CHF conditions are modest, leading to the conclusion that inlet orifices are only mildly effective at improving heat transfer coefficients. Stability of the PRL used for experimentation was also studied and improved. A vapor compression cycle's (VCC) proportional, integral, and derivative controller was found to adversely affect stability within the PRL and cause premature CHF. Replacing the VCC with an ice water heat sink maintained steady pumped loop system pressures and mass flow rates. The ice water heat sink was shown to have energy cost savings over the use of a directly coupled VCC for removing heat from the PRL.
ContributorsOdom, Brent A (Author) / Phelan, Patrick E (Thesis advisor) / Herrmann, Marcus (Committee member) / Trimble, Steve (Committee member) / Tasooji, Amaneh (Committee member) / Holcomb, Don (Committee member) / Arizona State University (Publisher)
Created2012
Description
This thesis uses an aircraft aerodynamic model and propulsion data, which
represents a configuration similar to the Airbus A320, to perform trade studies to understand the weight and configuration effects of “out-of-trim” flight during takeoff, cruise, initial approach, and balked landing. It is found that flying an aircraft slightly above the angle of attack or pitch angle required for a trimmed, stabilized flight will cause the aircraft to lose speed rapidly. This effect is most noticeable for lighter aircraft and when one engine is rendered inoperative. In the event of an engine failure, if the pilot does not pitch the nose of the aircraft down quickly, speed losses are significant and potentially lead to stalling the aircraft. Even when the risk of stalling the aircraft is small, the implications on aircraft climb performance, obstacle clearance, and acceleration distances can still become problematic if the aircraft is not flown properly. When the aircraft is slightly above the trimmed angle of attack, the response is shown to closely follow the classical phugoid response where the aircraft will trade speed and altitude in an oscillatory manner. However, when the pitch angle is slightly above the trimmed condition, the aircraft does not show this phugoid pattern but instead just loses speed until it reaches a new stabilized trajectory, never having speed and altitude oscillate. In this event, the way a pilot should respond to both events is different and may cause confusion in the cockpit.
represents a configuration similar to the Airbus A320, to perform trade studies to understand the weight and configuration effects of “out-of-trim” flight during takeoff, cruise, initial approach, and balked landing. It is found that flying an aircraft slightly above the angle of attack or pitch angle required for a trimmed, stabilized flight will cause the aircraft to lose speed rapidly. This effect is most noticeable for lighter aircraft and when one engine is rendered inoperative. In the event of an engine failure, if the pilot does not pitch the nose of the aircraft down quickly, speed losses are significant and potentially lead to stalling the aircraft. Even when the risk of stalling the aircraft is small, the implications on aircraft climb performance, obstacle clearance, and acceleration distances can still become problematic if the aircraft is not flown properly. When the aircraft is slightly above the trimmed angle of attack, the response is shown to closely follow the classical phugoid response where the aircraft will trade speed and altitude in an oscillatory manner. However, when the pitch angle is slightly above the trimmed condition, the aircraft does not show this phugoid pattern but instead just loses speed until it reaches a new stabilized trajectory, never having speed and altitude oscillate. In this event, the way a pilot should respond to both events is different and may cause confusion in the cockpit.
ContributorsDelisle, Mathew Robert (Author) / Takahashi, Timothy (Thesis advisor) / White, Daniel (Committee member) / Niemczyk, Mary (Committee member) / Arizona State University (Publisher)
Created2018
Description
This study identifies the influence that leading-edge shape has on the aerodynamic characteristics of a wing using surface far-field and near-field analysis. It examines if a wake survey is the appropriate means for measuring profile drag and induced drag. The paper unveils the differences between sharp leading-edge and blunt leading-edge wings with the tools of pressure loop, chordwise pressure distribution, span load plots and with wake integral computations. The analysis was performed using Computational Fluid Dynamics (CFD), vortex lattice potential flow code (VORLAX), and a few wind-tunnels runs to acquire data for comparison. This study found that sharp leading-edge wings have less leading-edge suction and higher drag than blunt leading-edge wings.
The blunt leading-edge wings have less drag because the normal vector of the surface in the front section of the airfoil develops forces at opposed skin friction. The shape of the leading edge, in conjunction with the effect of viscosity, slightly alter the span load; both the magnitude of the lift and the transverse distribution. Another goal in this study is to verify the veracity of wake survey theory; the two different leading-edge shapes reveals the shortcoming of Mclean’s equation which is only applicable to blunt leading-edge wings.
The blunt leading-edge wings have less drag because the normal vector of the surface in the front section of the airfoil develops forces at opposed skin friction. The shape of the leading edge, in conjunction with the effect of viscosity, slightly alter the span load; both the magnitude of the lift and the transverse distribution. Another goal in this study is to verify the veracity of wake survey theory; the two different leading-edge shapes reveals the shortcoming of Mclean’s equation which is only applicable to blunt leading-edge wings.
ContributorsOu, Che Wei (Author) / Takahashi, Timothy (Thesis advisor) / Herrmann, Marcus (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2019
Description
In previous work, the effects of power extraction for onboard electrical equipment and flight control systems were studied to determine which turbine shaft (i.e. high power shaft vs low power shaft) is best suited for power extraction. This thesis will look into an alternative option, a three-spool design with a high-pressure turbine, low-pressure turbine, and a turbine dedicated to driving the fan. One of the three-spool turbines is designed to be a vaneless counter-rotating turbine. The off-design performance of this new design will be compared to the traditional two-spool design to determine if the additional spool is a practical alternative to current designs for high shaft horsepower extraction requirements. Upon analysis, this thesis has shown that a three-spool engine with a vaneless counter-rotating stage has worse performance characteristics than traditional two-spool designs for UAV systems.
ContributorsBurgett, Luke Michael (Author) / Takahashi, Timothy (Thesis advisor) / Dahm, Werner (Committee member) / Trimble, Steve (Committee member) / Arizona State University (Publisher)
Created2019
Description
There are many computer aided engineering tools and software used by aerospace engineers to design and predict specific parameters of an airplane. These tools help a design engineer predict and calculate such parameters such as lift, drag, pitching moment, takeoff range, maximum takeoff weight, maximum flight range and much more. However, there are very limited ways to predict and calculate the minimum control speeds of an airplane in engine inoperative flight. There are simple solutions, as well as complicated solutions, yet there is neither standard technique nor consistency throughout the aerospace industry. To further complicate this subject, airplane designers have the option of using an Automatic Thrust Control System (ATCS), which directly alters the minimum control speeds of an airplane.
This work addresses this issue with a tool used to predict and calculate the Minimum Control Speed on the Ground (VMCG) as well as the Minimum Control Airspeed (VMCA) of any existing or design-stage airplane. With simple line art of an airplane, a program called VORLAX is used to generate an aerodynamic database used to calculate the stability derivatives of an airplane. Using another program called Numerical Propulsion System Simulation (NPSS), a propulsion database is generated to use with the aerodynamic database to calculate both VMCG and VMCA.
This tool was tested using two airplanes, the Airbus A320 and the Lockheed Martin C130J-30 Super Hercules. The A320 does not use an Automatic Thrust Control System (ATCS), whereas the C130J-30 does use an ATCS. The tool was able to properly calculate and match known values of VMCG and VMCA for both of the airplanes. The fact that this tool was able to calculate the known values of VMCG and VMCA for both airplanes means that this tool would be able to predict the VMCG and VMCA of an airplane in the preliminary stages of design. This would allow design engineers the ability to use an Automatic Thrust Control System (ATCS) as part of the design of an airplane and still have the ability to predict the VMCG and VMCA of the airplane.
This work addresses this issue with a tool used to predict and calculate the Minimum Control Speed on the Ground (VMCG) as well as the Minimum Control Airspeed (VMCA) of any existing or design-stage airplane. With simple line art of an airplane, a program called VORLAX is used to generate an aerodynamic database used to calculate the stability derivatives of an airplane. Using another program called Numerical Propulsion System Simulation (NPSS), a propulsion database is generated to use with the aerodynamic database to calculate both VMCG and VMCA.
This tool was tested using two airplanes, the Airbus A320 and the Lockheed Martin C130J-30 Super Hercules. The A320 does not use an Automatic Thrust Control System (ATCS), whereas the C130J-30 does use an ATCS. The tool was able to properly calculate and match known values of VMCG and VMCA for both of the airplanes. The fact that this tool was able to calculate the known values of VMCG and VMCA for both airplanes means that this tool would be able to predict the VMCG and VMCA of an airplane in the preliminary stages of design. This would allow design engineers the ability to use an Automatic Thrust Control System (ATCS) as part of the design of an airplane and still have the ability to predict the VMCG and VMCA of the airplane.
ContributorsHadder, Eric Michael (Author) / Takahashi, Timothy (Thesis advisor) / Mignolet, Marc (Committee member) / White, Daniel (Committee member) / Arizona State University (Publisher)
Created2016
Description
In today’s day and age, the use of automated technology is becoming increasingly prevalent. Throughout the aerospace industry, we see the use of automated systems in manufacturing, testing, and, progressively, in design. This thesis focuses on the idea of automated structural design that can be directly coupled with parametric Computer-Aided Drafting (CAD) and used to support aircraft conceptual design. This idea has been around for many years; however, with the advancement of CAD technology, it is becoming more realistic. Having the ability to input design parameters, analyze the structure, and produce a basic CAD model not only saves time in the design process but provides an excellent platform to communicate ideas. The user has the ability to change parameters and quickly determine the effect on the structure. Coupling this idea with automated parametric CAD provides visual verification and a platform to export into Finite Element Analysis (FEA) for further verification.
ContributorsAnderson, Benjamin Kyle (Author) / Takahashi, Timothy (Thesis advisor) / Bolukbasi, Akif (Committee member) / Patel, Jay (Committee member) / Arizona State University (Publisher)
Created2017
Description
This thesis describes the extension of an aircraft-style time-step integrating mission performance simulation to address aero-spaceplane design challenges. The result is a computationally lean program compatible with current Multi-Disciplinary Optimization schemes to assist in the conceptual design of hypersonic vehicles. To do this the starting aircraft style “Mission Code” required enhancements to the typical point-mass simulation for high altitude and high Mach flight. Stability parameters and the rigid-body modes of Short-Period and Dutch-Roll are tracked to understand time-domain limits to aerodynamic control, along with monitoring the Lateral Control Departure Parameter to ensure that the aircraft is not prone to spin. Additionally, experience has shown that for high Mach Number flight designers must consider aerothermodynamic effects early in the vehicle design process, and thus, an engineering level aerothermodynamic model is included. Comparisons to North American X-15 flight test datasets demonstrate the validity of this method in that application, and trade studies conducted show the utility of this application.
ContributorsGriffin, Jack Aidan (Author) / Takahashi, Timothy (Thesis advisor) / Dahm, Werner (Committee member) / Rodi, Patrick (Committee member) / Arizona State University (Publisher)
Created2022
Description
As the push to develop ever more efficient aircraft increases, the use of lightweight composite materials to meet this push has increased. Traditional aircraft structural component sizing has revolved around the tensile yield strength of materials. Since composite materials excel in tensile strength, these traditional sizing tools provide overly optimistic weight reduction predictions. Furthermore, composite materials, in general, are weak under compression and shear. Thus, proper structural sizing yields heavier-than-expected designs. Nevertheless, a wing using thin, lightweight composites in the primary load-bearing components significantly impacts its static aeroelastic properties. These thin structures have a decreased flexural rigidity, making them more susceptible to bending. The bending of swept wings decreases the design wing twist and dihedral angle, potentially impacting the aerodynamic performance and the lateral stability and control, respectively. This work aims to determine what, if any, are the effects of excessive static aeroelastic properties on the aerodynamic performance of an aircraft. Does the perceived gain in the theoretical reduction in structural weight outweigh the potential reduction in aerodynamic performance?
ContributorsWebb, Benjamin David (Author) / Takahashi, Timothy (Thesis advisor) / Herrmann, Marcus (Committee member) / Perez, Ruben (Committee member) / Arizona State University (Publisher)
Created2022
Description
The design and development process of high-lift systems for commercial transport aircraft has been historically heavily dependent on extensive experimental testing. Whether this testing be in wind tunnels or during aircraft testing, the number and extent of high-lift system variations that can be tested are limited. With technology advancements, analyzing the complex flow around high lift systems using detailed computational fluid dynamics (CFD) has become more common; but, CFD has limitations due to the computational costs for such analysis. An empirical approach can be taken to analyze such systems, but the insight gained from such methods is often limited to a main contributing factor. While these methods often produce reasonable solutions, they fail in showing, and many times overshadow, the important minor effects within complex systems.
This thesis aims to present insight on the need and design of multi-element high-lift systems by using a tool developed which utilizes a legacy vortex lattice potential flow code and methods described in classical aerodynamic literature. With this tool, numerous variations of high lift devices were studied to understand why commercial transport aircraft require a high-lift system. Furthermore, variations of complete high-lift systems were also studied to understand why certain design decisions were made on existing commercial transport aircraft. Ultimately, enough insight was obtained to proceed to design a functioning high-lift system for a commercial transport aircraft capable of meeting all established requirements and exhibit favorable flow separation conditions.
ContributorsMartinez Rodriguez, Gabino (Author) / Takahashi, Timothy (Thesis advisor) / Herrmann, Marcus (Committee member) / Sobester, Andras (Committee member) / Arizona State University (Publisher)
Created2021