Matching Items (16)
Filtering by
- All Subjects: Aerospace Engineering
- Creators: Takahashi, Timothy T
- Member of: Theses and Dissertations
Description
There are significant fuel consumption consequences for non-optimal flight operations. This study is intended to analyze and highlight areas of interest that affect fuel consumption in typical flight operations. By gathering information from actual flight operators (pilots, dispatch, performance engineers, and air traffic controllers), real performance issues can be addressed and analyzed. A series of interviews were performed with various individuals in the industry and organizations. The wide range of insight directed this study to focus on FAA regulations, airline policy, the ATC system, weather, and flight planning. The goal is to highlight where operational performance differs from design intent in order to better connect optimization with actual flight operations. After further investigation and consensus from the experienced participants, the FAA regulations do not need any serious attention until newer technologies and capabilities are implemented. The ATC system is severely out of date and is one of the largest limiting factors in current flight operations. Although participants are pessimistic about its timely implementation, the FAA's NextGen program for a future National Airspace System should help improve the efficiency of flight operations. This includes situational awareness, weather monitoring, communication, information management, optimized routing, and cleaner flight profiles like Required Navigation Performance (RNP) and Continuous Descent Approach (CDA). Working off the interview results, trade-studies were performed using an in-house flight profile simulation of a Boeing 737-300, integrating NASA legacy codes EDET and NPSS with a custom written mission performance and point-performance "Skymap" calculator. From these trade-studies, it was found that certain flight conditions affect flight operations more than others. With weather, traffic, and unforeseeable risks, flight planning is still limited by its high level of precaution. From this study, it is recommended that air carriers increase focus on defining policies like load scheduling, CG management, reduction in zero fuel weight, inclusion of performance measurement systems, and adapting to the regulations to best optimize the spirit of the requirement.. As well, air carriers should create a larger drive to implement the FAA's NextGen system and move the industry into the future.
ContributorsHeitzman, Nicholas (Author) / Takahashi, Timothy T (Thesis advisor) / Wells, Valana (Thesis advisor) / Feigh, Karen (Committee member) / Arizona State University (Publisher)
Created2014
Description
This thesis seeks to further explore off-design point operation of gas turbines and to examine the capabilities of GasTurb 12 as a tool for off-design analysis. It is a continuation of previous thesis work which initially explored the capabilities of GasTurb 12. The research is conducted in order to: 1) validate GasTurb 12 and, 2) predict off-design performance of the Garrett GTCP85-98D located at the Arizona State University Tempe campus. GasTurb 12 is validated as an off-design point tool by using the program to predict performance of an LM2500+ marine gas turbine. Haglind and Elmegaard (2009) published a paper detailing a second off-design point method and it includes the manufacturer's off-design point data for the LM2500+. GasTurb 12 is used to predict off-design point performance of the LM2500+ and compared to the manufacturer's data. The GasTurb 12 predictions show good correlation. Garrett has published specification data for the GTCP85-98D. This specification data is analyzed to determine the design point and to comment on off-design trends. Arizona State University GTCP85-98D off-design experimental data is evaluated. Trends presented in the data are commented on and explained. The trends match the expected behavior demonstrated in the specification data for the same gas turbine system. It was originally intended that a model of the GTCP85-98D be constructed in GasTurb 12 and used to predict off-design performance. The prediction would be compared to collected experimental data. This is not possible because the free version of GasTurb 12 used in this research does not have a module to model a single spool turboshaft. This module needs to be purchased for this analysis.
ContributorsMartinjako, Jeremy (Author) / Trimble, Steve (Thesis advisor) / Dahm, Werner (Committee member) / Middleton, James (Committee member) / Arizona State University (Publisher)
Created2014
Description
Recent literature indicates potential benefits in microchannel cooling if an inlet orifice is used to suppress pressure oscillations that develop under two-phase conditions. This study investigates the costs and benefits of using an adjustable microchannel inlet orifice. The focus is on orifice effect during steady-state boiling and critical heat flux (CHF) in the channels using R134a in a pumped refrigerant loop (PRL). To change orifice size, a dam controlled with a micrometer was placed in front of 31 parallel microchannels. Each channel had a hydraulic diameter of 0.235 mm and a length of 1.33 cm. For steady state two-phase conditions, mass fluxes of 300 kg m-2 s-1 and 600 kg m-2 s-1were investigated. For orifice sizes with a hydraulic diameter to unrestricted hydraulic diameter (Dh:Dh,ur) ratio less than 35 percent, oscillations were reduced and wall temperatures fell up to 1.5 °C. Critical heat flux data were obtained for 7 orifice sizes with mass fluxes from 186 kg m-2 s-1 to 847 kg m-2 s-1. For all mass fluxes and inlet conditions tested, CHF values for a Dh:Dh,ur ratio of 1.8 percent became increasingly lower (up to 37 W cm-2 less) than those obtained with larger orifices. An optimum orifice size with Dh:Dh,ur of 35 percent emerged, offering up to 5 W cm-2 increase in CHF over unrestricted conditions at the highest mass flux tested, 847 kg m-2 s-1. These improvements in cooling ability with inlet orifices in place under both steady-state and impending CHF conditions are modest, leading to the conclusion that inlet orifices are only mildly effective at improving heat transfer coefficients. Stability of the PRL used for experimentation was also studied and improved. A vapor compression cycle's (VCC) proportional, integral, and derivative controller was found to adversely affect stability within the PRL and cause premature CHF. Replacing the VCC with an ice water heat sink maintained steady pumped loop system pressures and mass flow rates. The ice water heat sink was shown to have energy cost savings over the use of a directly coupled VCC for removing heat from the PRL.
ContributorsOdom, Brent A (Author) / Phelan, Patrick E (Thesis advisor) / Herrmann, Marcus (Committee member) / Trimble, Steve (Committee member) / Tasooji, Amaneh (Committee member) / Holcomb, Don (Committee member) / Arizona State University (Publisher)
Created2012
Description
Two methods of improving the life and efficiency of the Pulsed Inductive Thruster
(PIT) have been investigated. The first is a trade study of available switches to
determine the best device to implement in the PIT design. The second is the design
of a coil to improve coupling between the accelerator coil and the plasma. Experiments
were done with both permanent and electromagnets to investigate the feasibility of
implementing a modified Halbach array within the PIT to promote better plasma
coupling and decrease the unused space within the thruster. This array proved to
promote more complete coupling on the edges of the coil where it had been weak in
previous studies. Numerical analysis was done to predict the performance of a PIT
that utilized each suggested switch type. This model utilized the Alfven velocity to
determine the critical mass and energy of these theoretical thrusters.
(PIT) have been investigated. The first is a trade study of available switches to
determine the best device to implement in the PIT design. The second is the design
of a coil to improve coupling between the accelerator coil and the plasma. Experiments
were done with both permanent and electromagnets to investigate the feasibility of
implementing a modified Halbach array within the PIT to promote better plasma
coupling and decrease the unused space within the thruster. This array proved to
promote more complete coupling on the edges of the coil where it had been weak in
previous studies. Numerical analysis was done to predict the performance of a PIT
that utilized each suggested switch type. This model utilized the Alfven velocity to
determine the critical mass and energy of these theoretical thrusters.
ContributorsRaines, Taylor (Author) / Takahashi, Timothy T (Thesis advisor) / White, Daniel B (Committee member) / Dahm, Werner (Committee member) / Arizona State University (Publisher)
Created2018
Description
This paper describes an effort to bring wing structural stiffness and aeroelastic considerations early in the conceptual design process with an automated tool. Stiffness and aeroelasticity can be well represented with a stochastic model during conceptual design because of the high level of uncertainty and variability in wing non-structural mass such as fuel loading and control surfaces. To accomplish this, an improvement is made to existing design tools utilizing rule based automated design to generate wing torque box geometry from a specific wing outer mold-line. Simple analysis on deflection and inferred stiffness shows how early conceptual design choices can strongly impact the stiffness of the structure. The impacts of design choices and how the buckling constraints drive structural weight in particular examples are discussed. The model is then carried further to include a finite element model (FEM) to analyze resulting mode shapes and frequencies for use in aeroelastic analysis. The natural frequencies of several selected wing torque boxes across a range of loading cases are compared.
ContributorsMiskin, Daniel L (Author) / Takahashi, Timothy T (Thesis advisor) / Mignolet, Marc (Committee member) / Murthy, Raghavendra (Committee member) / Arizona State University (Publisher)
Created2018
Description
In previous work, the effects of power extraction for onboard electrical equipment and flight control systems were studied to determine which turbine shaft (i.e. high power shaft vs low power shaft) is best suited for power extraction. This thesis will look into an alternative option, a three-spool design with a high-pressure turbine, low-pressure turbine, and a turbine dedicated to driving the fan. One of the three-spool turbines is designed to be a vaneless counter-rotating turbine. The off-design performance of this new design will be compared to the traditional two-spool design to determine if the additional spool is a practical alternative to current designs for high shaft horsepower extraction requirements. Upon analysis, this thesis has shown that a three-spool engine with a vaneless counter-rotating stage has worse performance characteristics than traditional two-spool designs for UAV systems.
ContributorsBurgett, Luke Michael (Author) / Takahashi, Timothy (Thesis advisor) / Dahm, Werner (Committee member) / Trimble, Steve (Committee member) / Arizona State University (Publisher)
Created2019
Description
Modern aircraft are expected to fly faster and more efficiently than their predecessors. To improve aerodynamic efficiency, designers must carefully consider and handle shock wave formation. Presently, many designers utilize computationally heavy optimization methods to design wings. While these methods may work, they do not provide insight. This thesis aims to better understand fundamental methods that govern wing design. In order to further understand the flow in the transonic regime, this work revisits the Transonic Similarity Rule. This rule postulates an equivalent incompressible geometry to any high speed geometry in flight and postulates a “stretching” analogy. This thesis utilizes panel methods and Computational Fluid Dynamics (CFD) to show that the “stretching” analogy is incorrect, but instead the flow is transformed by a nonlinear “scaling” of the flow velocity. This work also presents data to show the discrepancies between many famous authors in deriving the accurate Critical Pressure Coefficient (Cp*) equation for both swept and unswept wing sections. The final work of the thesis aims to identify the correct predictive methods for the Critical Pressure Coefficient.
ContributorsKirkman, Jeffrey J (Author) / Takahashi, Timothy T (Thesis advisor) / Wells, Valana (Committee member) / Herman, Marcus (Committee member) / Arizona State University (Publisher)
Created2016
Description
This thesis gives a detailed design process for a pulsed type thruster. The thrust stand designed in this paper is for a Pulsed Plasma Thruster built by Sun Devil Satellite Laboratory, a student organization at Arizona State University. The thrust stand uses a torsional beam rotating to record displacement. This information, along with impulse-momentum theorem is applied to find the impulse bit of the thruster, which varies largely from other designs which focus on using the natural dynamics their fixtures. The target impulse to record on this fixture was estimated to be 275 μN-s of impulse. Through calibration and experimentation, the fixture is capable of recording an impulse of 332 μN-s ± 14.81 μN-s, close to the target impulse. The error due to noise was characterized and evaluated to be under 5% which is deemed to be acceptable.
ContributorsVerbin, Andrew Joseph (Author) / Takahashi, Timothy T (Thesis advisor) / White, Daniel B (Thesis advisor) / Rykaczewski, Konrad (Committee member) / Arizona State University (Publisher)
Created2017
Description
This thesis explores the human factors effects pilots have when controlling the aircraft during the takeoff phase of flight. These variables come into play in the transitory phase from ground roll to flight, and in the initiation of procedures to abort a takeoff during the ground run. The FAA provides regulations for manufacturers and operators to follow, ensuring safe manufacture of aircraft and pilots that fly without endangering the passengers; however, details regarding accounting of piloting variability are lacking. Creation of a numerical simulation allowed for the controlled variation of isolated piloting procedures in order to evaluate effects on field performance. Reduced rotation rates and delayed reaction times were found to cause significant increases in field length requirements over values published in the AFM. A pilot survey was conducted to evaluate common practices for line pilots in the field, which revealed minimum regulatory compliance is exercised with little to no feedback on runway length requirements. Finally, observation of pilots training in a CRJ-200 FTD gathered extensive information on typical piloting timings in the cockpit. AEO and OEI takeoffs were observed, as well as RTOs. Pilots showed large variability in procedures and timings resulting in significant inconsistency in runway distances used as well as V-speed compliance. The observed effects from pilot timing latency correlated with the numerical simulation increased field length outputs. Variability in piloting procedures results in erratic field performance that deviates from AFM published values that invite disaster in an aircraft operating near its field performance limitations.
ContributorsWood, Donald L (Author) / Takahashi, Timothy T (Thesis advisor) / Niemczyk, Mary (Thesis advisor) / Files, Greg (Committee member) / Arizona State University (Publisher)
Created2017
Description
To ensure safety is not precluded in the event of an engine failure, the FAA has
established climb gradient minimums enforced through Federal Regulations.
Furthermore, to ensure aircraft do not accidentally impact an obstacle on takeoff due to
insufficient climb performance, standard instrument departure procedures have their own
set of climb gradient minimums which are typically more than those set by Federal
Regulation. This inconsistency between climb gradient expectations creates an obstacle
clearance problem: while the aircraft has enough climb gradient in the engine inoperative
condition so that basic flight safety is not precluded, this climb gradient is often not
strong enough to overfly real obstacles; this implies that the pilot must abort the takeoff
flight path and reverse course back to the departure airport to perform an emergency
landing. One solution to this is to reduce the dispatch weight to ensure that the aircraft
retains enough climb performance in the engine inoperative condition, but this comes at
the cost of reduced per-flight profits.
An alternative solution to this problem is the extended second segment (E2S)
climb. Proposed by Bays & Halpin, they found that a C-130H gained additional obstacle
clearance performance through this simple operational change. A thorough investigation
into this technique was performed to see if this technique can be applied to commercial
aviation by using a model A320 and simulating multiple takeoff flight paths in either a
calm or constant wind condition. A comparison of takeoff flight profiles against real
world departure procedures shows that the E2S climb technique offers a clear obstacle
clearance advantage which a scheduled four-segment flight profile cannot provide.
established climb gradient minimums enforced through Federal Regulations.
Furthermore, to ensure aircraft do not accidentally impact an obstacle on takeoff due to
insufficient climb performance, standard instrument departure procedures have their own
set of climb gradient minimums which are typically more than those set by Federal
Regulation. This inconsistency between climb gradient expectations creates an obstacle
clearance problem: while the aircraft has enough climb gradient in the engine inoperative
condition so that basic flight safety is not precluded, this climb gradient is often not
strong enough to overfly real obstacles; this implies that the pilot must abort the takeoff
flight path and reverse course back to the departure airport to perform an emergency
landing. One solution to this is to reduce the dispatch weight to ensure that the aircraft
retains enough climb performance in the engine inoperative condition, but this comes at
the cost of reduced per-flight profits.
An alternative solution to this problem is the extended second segment (E2S)
climb. Proposed by Bays & Halpin, they found that a C-130H gained additional obstacle
clearance performance through this simple operational change. A thorough investigation
into this technique was performed to see if this technique can be applied to commercial
aviation by using a model A320 and simulating multiple takeoff flight paths in either a
calm or constant wind condition. A comparison of takeoff flight profiles against real
world departure procedures shows that the E2S climb technique offers a clear obstacle
clearance advantage which a scheduled four-segment flight profile cannot provide.
ContributorsBeard, John Eng Hui (Author) / Takahashi, Timothy T (Thesis advisor) / White, Daniel (Committee member) / Niemczyk, Mary (Committee member) / Arizona State University (Publisher)
Created2017