Matching Items (31)
Filtering by
- All Subjects: Aerodynamics
- All Subjects: Additive Manufacturing
- Creators: Mechanical and Aerospace Engineering Program
Description
This experiment used hotwire anemometry to examine the von Kármán vortex street and how different surface conditions affect the wake profile of circular airfoils, or bluff bodies. Specifically, this experiment investigated how the various surface conditions affected the shedding frequency and Strouhal Number of the vortex street as Reynolds Number is increased. The cylinders tested varied diameter, surface finish, and wire wrapping. Larger diameters corresponded with lower shedding frequencies, rougher surfaces decreased Strouhal Number, and the addition of thick wires to the surface of the cylinder completely disrupted the vortex shedding to the point where there was almost no dominant shedding frequency. For the smallest diameter cylinder tested, secondary dominant frequencies were observed, suggesting harmonics.
ContributorsCoote, Peter John (Author) / Takahashi, Timothy (Thesis director) / White, Daniel (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
Active flow control for airfoil designs has been researched for the past few decades. This has been achieved through steady blowing, pulsed blowing, synthetic jets, and plasma jets. These techniques have been applied to both single and dual jet configurations. This technology was examined for a wind turbine blade application so that lift and drag can be altered without needing a mechanical flap. Research was completed to also allow for thicker airfoils with more blunt trailing edges that result in the higher structural strength needed for large, heavy wind turbine blades without the negative aerodynamic effects such as boundary layer separation. This research tested steady blowing in a dual jet configuration for the S830 airfoil from the National Renewable Energy Laboratory (NREL) database of airfoils. Computational Fluid Dynamics was used in the software Ansys Fluent. Calculations were completed for a modified S830 airfoil with a rounded trailing edge surface at momentum coefficients of 0.01 for the lower jet and 0.1, 0.12, and 0.14 for the upper jet. These results were then compared to the original S830 results for the lift over drag efficiency. The design with momentum coefficients of 0.12 for the upper surface resulted in the highest increase in efficiency of 53% at an angle of attack of 12 degrees. At this momentum coefficient, the angle of attack where zero lift occurred was at -8.62 degrees, compared to the case with no blowing at -1.90 degrees. From previous research and research completed in this thesis it was concluded that active flow control is an effective technique to improve wind turbine energy collection.
ContributorsStapleton, Paige (Author) / Mertz, Benjamin (Thesis director) / Herrmann, Marcus (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
Description
Active pixel sensors hold a lot of promise for space applications in star tracking because of their effectiveness against radiation, small size, and on-chip processing. The research focus is on documenting and validating ground test equipment for these types of sensors. Through demonstrating the utility of a commercial sensor, the research will be able to work on ensuring the accuracy of ground tests. This contribution allows for future research on improving active pixel sensor performance.
ContributorsDotson, Breydan Lane (Author) / White, Daniel (Thesis director) / Jansen, Rolf (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
Description
The emerging market for unmanned aerial vehicles, or UAV's, demands the development of effective design tools for small-scale aircraft. This research seeks to validate a previously developed drag build-up method for small air vehicles. Using the method, a drag prediction was made for an off-the-shelf, remotely controlled aircraft. The Oswald efficiency was predicted to be 0.852. Flight tests were then conducted using the RC plane, and the aircraft performance data was compared with the predicted performance data. Although there were variations in the data due to flight conditions and equipment, the drag build up method was capable of predicting the aircraft's drag. The experimental Oswald efficiency was found to be 0.863 with an error of 1.27%. As for the CDp the prediction of 0.0477 was comparable to the experimental value of 0.0424. Moving forward this method can be used to create conceptual designs of UAV's to explore the most efficient designs, without the need to build a model.
ContributorsGavin, Tyler Joseph (Author) / Wells, Valana (Thesis director) / Garrett, Fred (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor)
Created2014-05
Description
This paper summarizes the [1] ideas behind, [2] needs, [3] development, and [4] testing of 3D-printed sensor-stents known as Stentzors. This sensor was successfully developed entirely from scratch, tested, and was found to have an output of 3.2*10-6 volts per RMS pressure in pascals. This paper also recommends further work to render the Stentzor deployable in live subjects, including [1] further design optimization, [2] electrical isolation, [3] wireless data transmission, and [4] testing for aneurysm prevention.
ContributorsMeidinger, Aaron Michael (Author) / LaBelle, Jeffrey (Thesis director) / Frakes, David (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor)
Created2014-05
Description
The aerospace industry has been conducting research on the additive manufacturing (AM) process since the 1980's, but companies have recently just begun to apply AM in hopes that this new technology will meet or exceed the requirements met by previous manufacturing methods, as well as producing more cost effective, geometrically-complex products. This investigation evaluated the performance of 3D-printed aerospace test specimens made by Powder Bed Fusion Technologies, and compared them to forged specimens. A design of experiments varying build parameters was conducted in order to determine AM component porosity. Factors such as powder post-processing, directionality of the build, and fractology of the samples were evaluated through tensile strength testing and hardness testing of Inconel 718 wrought and EBM printed materials. Using electron microsopy, the responses to these factors were analyzed for stress fractures, grain boundaries, and other defects that occurred in the testing process. The comparison determined which metallurgical process provides the most effective material for aircraft usage.
ContributorsNez, Brittany Amber (Author) / Parsey, John (Thesis director) / Hsu, Keng (Committee member) / Godfrey, Donald (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / School of Earth and Space Exploration (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
Automobiles can advance greatly with the introduction of metal additive manufactured components. Additive tooling is slowly becoming additive manufacturing and someday the technology will be advanced enough that high volume can be supported. This research was conducted in order to show the advantages metal additive manufacturing has in the automobile industry. One large advantage to metal additive manufacturing is mass reduction. Components can be designed for production with different geometries than other manufacturing methods. The change in geometry can significantly reduce the product volume and therefore mass. Overall, mass reduction in the automotive industry is beneficial. Mass reduction can increase performance and fuel economy of the car. Once metal additive manufacturing becomes capable of higher production, metal additive manufacturing will play a major role in automobile manufacturing. Research was conducted to design and produce an optimized AC compressor bracket. The bracket was designed to the specifications of the OEM component, and the mass was reduced by more than half.
ContributorsSawyer, Brenton James (Author) / Hsu, Keng (Thesis director) / Parsey, John (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
This study analyzes mechanical properties of additively manufactured plastic materials produced in a conventional 3D printer. This topic has generally been studied in controlled scenarios, and this study aims to reflect the properties seen by consumers. Layered prints are inherently anisotropic due to the direction of the layers and associated weaknesses or stress concentrators. Thus, the ultimate strength and elastic modulus of plastic specimens produced using default settings are compared based on print orientation angle, and trends are observed. When a specimen is parallel to the build plate, it tends to have ultimate strength and elastic modulus near the published bulk values of 13.2MPa and 404-710MPa, but these values tend to decrease as the print angle increases.
ContributorsGarry, Allan Edward (Author) / Patel, Jay (Thesis director) / Mertz, Benjamin (Committee member) / School of Mathematical and Statistical Sciences (Contributor) / Mechanical and Aerospace Engineering Program (Contributor) / Materials Science and Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
Description
Each year, the CanSat Competition organizers release aerospace based engineering mission objectives for collegiate teams to compete in. This year, the design is an aerodynamically stable probe that will descend from an altitude of 725 meters at a rate between 10-30 meters/sec until it reaches an altitude of 300 meters, where it will then release a parachute as its aerobraking mechanism as it descends at 5 meters/sec until it reaches the ground. The focus of this paper is to investigate the design of the probe itself and how slender body theory and cross flow drag affect the lift and aerodynamic stability of this bluff body. A tool is developed inside of MATLAB which calculates the slender body lift as well as the lift from the cross flow drag. It then uses that information to calculate the total moment about the center of gravity for a range of angles of attack and free stream velocities. This tool is then used to optimize the geometry of the probe. These geometries are used to construct a prototype and that prototype is tested by a drop test from a 6-story building. The initial tests confirm the calculations that the probe, bluff body, is stable and self-correcting in its descent. Future work involves more high-altitude and ground-level tests that will further verify and improve on the current design.
ContributorsMcCourt, Anthony Michael (Author) / Takahashi, Timothy (Thesis director) / Herrmann, Marcus (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
Description
This study consisted of two fundamental experiments that examined the effects of surface parameters on baseball aerodynamics. The first experiment measured drag and lift coefficients in response to varied surface treatments of a non-spinning baseball. This experiment found that rougher surfaces (rubbing mud, increased ball usage, and scuffing) decrease drag coefficient by up to 0.05 for Reynolds numbers of up to 1.5x105 (wind speeds of 30 m/s or 67 mph). The maximum observed increase in lift coefficient was 0.20, caused by heavily scuffing the top of the ball. These results can be explained by boundary layer transition phenomena and asymmetry in the surface roughness of the ball. A decrease in drag coefficient of 0.05 can translate to an increase in the flight distance of a batted ball by as much as 50 ft (14%), and an increase of 0.20 in lift coefficient can increase flight distance by 70 ft (19%) \u2014 numbers that can easily mean the difference between a routine fly out and a monster home run. The second experiment measured drag and lift coefficients in response to varied stitch geometries of a non-spinning, 3D-printed baseball. Increasing stitch height, width, and spacing was found to increase drag coefficient, while increasing stitch length had little effect on lift coefficient. Increasing any parameter of the stitch geometry was found to increase lift coefficient. These results can be explained by boundary layer transition phenomena, blockage effects, and asymmetry in the stitch geometry of the ball. Future work would do well to repeat these experiments with a larger wind tunnel and a more sensitive force balance. These results should also be validated at higher wind speeds, and for spinning, rather than stationary baseballs. In addition, future work should explore the degree to which surface roughness and stitch geometry affect drag and lift coefficients at different ball orientations.
ContributorsDwight, Jeremiah Robert (Author) / Squires, Kyle (Thesis director) / Steele, Bruce (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05