Matching Items (41)
Filtering by
- All Subjects: robotics
- Creators: Lee, Hyunglae
Description
Presented in this thesis are two projects that fall under the umbrella of magnetically actuated electronics and robotics for medical applications. First, magnetically actuated tunable soft electronics are discussed in Chapter 2. Wearable and implantable soft electronics are clinically available and commonplace. However, these devices can be taken a step further to improve the lives of their users by adding remote tunability. The four electric units tested were planar inductors, axial inductors, capacitors and resistors. The devices were made of polydimethylsiloxane (PDMS) for flexibility with copper components for conductivity. The units were tuned using magnets and mobile components comprised of iron filings and ferrofluid. The characteristic properties examined for each unit are as follows: inductance and quality factor (Q-factor) for inductors, capacitance and Q-factor for capacitors, and impedance for resistors. There were two groups of tuning tests: quantity effect and position effect of the mobile component. The position of the mobile component had a larger effect on each unit, with 20-23% change in inductance for inductors (from 3.31 µH for planar and 0.44 µH for axial), 12.7% from 2.854 pF for capacitors and 185.3% from 0.353 kΩ for resistors.
Chapter 3 discusses a magnetic needle tracking device with operative assistance from a six degree-of-freedom robotic arm. Traditional needle steering faces many obstacles such as torsional effects, buckling, and small radii of curvature. To improve upon the concept, this project uses permanent magnets in parallel with a tracking system to steer and determine the position and orientation of the needle in real time. The magnet configuration is located at the end effector of the robotic arm. The trajectory of the end effector depends on the needle’s path, and vice versa. The distance the needle travels inside the workspace is tracked by a direct current (DC) motor, to which the needle is tethered. Combining this length with the pose of the end effector, the position and orientation of the needle can be calculated. Simulation of this tracking device has shown the functionality of the system. Testing has been done to confirm that a single magnet pulls the needle through the phantom tissue.
Chapter 3 discusses a magnetic needle tracking device with operative assistance from a six degree-of-freedom robotic arm. Traditional needle steering faces many obstacles such as torsional effects, buckling, and small radii of curvature. To improve upon the concept, this project uses permanent magnets in parallel with a tracking system to steer and determine the position and orientation of the needle in real time. The magnet configuration is located at the end effector of the robotic arm. The trajectory of the end effector depends on the needle’s path, and vice versa. The distance the needle travels inside the workspace is tracked by a direct current (DC) motor, to which the needle is tethered. Combining this length with the pose of the end effector, the position and orientation of the needle can be calculated. Simulation of this tracking device has shown the functionality of the system. Testing has been done to confirm that a single magnet pulls the needle through the phantom tissue.
ContributorsEdwards, Dakota (Author) / Marvi, Hamidreza (Thesis advisor) / Lee, Hyunglae (Committee member) / Berman, Spring (Committee member) / Arizona State University (Publisher)
Created2020
Description
Unmanned subsurface investigation technologies for the Moon are of special significance for future exploration when considering the renewed interest of the international community for this interplanetary destination. In precision agriculture, farmers demand quasi-real-time sensors and instruments with remote crop and soil detection properties to meet sustainability goals and achieve healthier and higher crop yields. Hence, there is the need for a robot that will be able to travel through the soil and conduct sampling or in-situ analysis of the subsurface materials on earth and in space. This thesis presents the design, fabrication, and characterization of a robot that can travel through the soil. The robot consists of a helical screw design coupled with a fin that acts as an anchor. The fin design is an integral part of the robot, allowing it to travel up and down the medium unaided. Experiments were performed to characterize different designs. It was concluded that the most energy-efficient speed from traveling down the medium is 20 rpm, while 60 rpm was the efficient speed for traveling up the medium. This research provides vital insight into developing subsurface robots enabling us to unearth the valuable knowledge that subsurface environment holds to help the agricultural, construction, and exploration communities.
ContributorsOkwae, Nana Kwame Kwame (Author) / Marvi, Hamidreza (Thesis advisor) / Tao, Jungliang (Committee member) / Lee, Hyunglae (Committee member) / Arizona State University (Publisher)
Created2020
Description
This paper introduces a variable impedance controller which dynamically modulates both its damping and stiffness to improve the trade-off between stability and agility in coupled human-robot systems and reduce the human user’s effort. The controller applies a range of robotic damping from negative to positive values to either inject or dissipate energy based on the user’s intent of motion. The controller also estimates the user’s intent of direction and applies a variable stiffness torque to stabilize the user towards an estimated ideal trajectory. To evaluate the controller’s ability to improve the stability/agility trade-off and reduce human effort, a study was designed for human subjects to perform a 2D target reaching task while coupled with a wearable ankle robot. A constant impedance condition was selected as a control with which to compare the variable impedance condition. The position, speed, and muscle activation responses were used to quantify the user’s stability, agility, and effort, respectively. Stability was quantified spatially and temporally, with both overshoot and stabilization time showing no statistically significant difference between the two experimental conditions. Agility was quantified using mean and maximum speed, with both increasing from the constant impedance to variable impedance condition by 29.8% and 59.9%, respectively. Effort was quantified by the overall and maximum muscle activation data, both of which showed a ~10% reduction in effort. Overall, the study demonstrated the effectiveness of the variable impedance controller.
ContributorsArnold, James (Author) / Lee, Hyunglae (Thesis advisor) / Berman, Spring (Committee member) / Yong, Sze Zheng (Committee member) / Arizona State University (Publisher)
Created2021
Description
Regolith excavation systems are the enabling technology that must be developed in order to implement many of the plans for in-situ resource utilization (ISRU) that have been developed in recent years to aid in creating a lasting human presence on the surface of the Moon, Mars, and other celestial bodies. The majority of proposed ISRU excavation systems are integrated onto a wheeled mobility system, however none yet have proposed the use of a screw-propelled vehicle, which has the potential to augment and enhance the capabilities of the excavation system. As a result, CASPER, a novel screw-propelled excavation rover is developed and analyzed to determine its effectiveness as a ISRU excavation system. The excavation rate, power, velocity, cost of transport, and a new parameter, excavation transport rate, are analyzed for various configurations of the vehicle through mobility and excavation tests performed in silica sand. The optimal configuration yielded a 28.4 kg/hr excavation rate and11.2 m/min traverse rate with an overall system mass of 3.4 kg and power draw of26.3 W. CASPER’s mobility and excavation performance results are compared to four notable proposed ISRU excavation systems of various types. The results indicate that this architecture shows promise as an ISRU excavator because it provides significant excavation capability with low mass and power requirements.
ContributorsGreen, Marko (Author) / Marvi, Hamid (Thesis advisor) / Emady, Heather (Committee member) / Lee, Hyunglae (Committee member) / Arizona State University (Publisher)
Created2021
Description
This work presents the design, modeling, analysis, and experimental characterization and testing of soft wearable robotics for lower limb rehabilitation for the ankle and hip. The Soft Robotic Ankle-Foot Orthosis (SR-AFO) is a wearable soft robot designed using multiple pneumatically-powered soft actuators to assist the ankle in multiple degrees-of-freedom during standing and walking tasks. The flat fabric pneumatic artificial muscle (ff-PAM) contracts upon pressurization and assists ankle plantarflexion in the sagittal plane. The Multi-material Actuator for Variable Stiffness (MAVS) aids in supporting ankle inversion/eversion in the frontal plane. Analytical models of the ff-PAM and MAVS were created to understand how the changing of the design parameters affects tensile force generation and stiffness support, respectively. The models were validated by both finite element analysis and experimental characterization using a universal testing machine. A set of human experiments were performed with healthy participants: 1) to measure lateral ankle support during quiet standing, 2) to determine lateral ankle support during walking over compliant surfaces, and 3) to evaluate plantarflexion assistance at push-off during treadmill walking, and 4) determine if the SR-AFO could be used for gait entrainment. Group results revealed increased ankle stiffness during quiet standing with the MAVS active, reduced ankle deflection while walking over compliant surfaces with the MAVS active, and reduced muscle effort from the SOL and GAS during 40 - 60% of the gait cycle with the dual ff-PAM active. The SR-AFO shows promising results in providing lateral ankle support and plantarflexion assistance with healthy participants, and a drastically increased basin of entrainment, which suggests a capability to help restore the gait of impaired users in future trials. The ff-PAM actuators were used in an X-orientation to assist the hip in flexion and extension. The Soft Robotic Hip Exosuit (SR-HExo) was evaluated using the same set of actuators and trials with healthy participants showed reduction in muscle effort during hip flexion and extension to further enhance the study of soft fabric actuators on human gait assistance.
ContributorsThalman, Carly Megan (Author) / Lee, Hyunglae (Thesis advisor) / Artemiadis, Panagiotis (Thesis advisor) / Sugar, Thomas (Committee member) / Zhang, Wenlong (Committee member) / Arizona State University (Publisher)
Created2021
Description
A heterogeneous team of robots working in symbiosis can maximize their strengths while complementing each other’s weaknesses. These simple robots can achieve more working together than they could on their own but cost less than a single robot with the same combination of capabilities. This project aims to validate the symbiotic relationship of an Unmanned Aerial Vehicle (UAV) and an Unmanned Ground Vehicle (UGV) with a physical implementation of a heterogenous team of robots and a demonstration of their capabilities. This paper details the selection of robots, the design of the physical coupling mechanism, and the design of the autonomous controls. An experiment was performed to assess the capabilities of the robots according to four performance criteria. The UGV must navigate a space while the UAV follows. The UAV must couple with the UGV. The UAV must lift the UGV over an obstacle. The UGV must navigate the space while carrying the UAV.
ContributorsBreaux, Chris (Author) / Artemiadis, Panagiotis (Thesis director) / Lee, Hyunglae (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2019-12
Description
Mechanical impedance is a concept that is used to model biomechanical propertiesof human joints. These models can then be utilized to provide insight into the inner
workings of the human neuromuscular system or to provide insight into how to best
design controllers for robotic applications that either attempt to mimic capabilities of
the human neuromuscular system or physically interact with it. To further elucidate
patterns and properties of how the human neuromuscular system modulates mechanical
impedance at the human ankle joint, multiple studies were conducted. The first
study was to assess the ability of linear regression models to characterize the change
in stiffness - a component of mechanical impedance - seen at the human ankle during
the stance phase of walking in the Dorsiflexion-Plantarflexion (DP) direction. A
collection of biomechanical variables were used as input variables. The R^2 value of
the best performing model was 0.71. The second and third studies were performed to
showcase the ability of a newly developed twin dual-axis platform, which goes beyond
the limits of a single dual-axis platform, to quantify bilateral stiffness properties. The
second study quantified the bilateral mechanical stiffness of the human ankle joint
for healthy able-bodied subjects during the stance phase of walking and during quiet
standing in both the DP and inversion-eversion directions. Subjects showed a high
level of subject specific symmetry. Lastly, a similar bilateral ankle characterization
study was conducted on a set of subjects with multiple sclerosis, but only during
quiet standing and in the DP direction. Results showed a high level of discrepancy
between the subject’s most-affected and least-affected limbs with a larger range and
variance than in the healthy population.
ContributorsRussell, Joshua (Author) / Lee, Hyunglae (Thesis advisor) / Honeycutt, Claire (Committee member) / Marvi, Hamid (Committee member) / Arizona State University (Publisher)
Created2022
Description
Medical technology, while improving greatly with time, often requires a sacrifice in the form of invasiveness in order to reach target areas within the body, such as the brain, liver, or heart. This project aims to utilize a magnetic, flexible needle design to reach these target areas for surgery and drug administration with minimal invasiveness. The metallic needle tip is guided by an external system consisting of a UR16e robotic arm with a magnetic end effector. As a longer running project, the primary focuses of this research are to develop the system by which the robotic arm guides the needle, investigate and implement fiber Bragg grating sensors as a means of real time path imaging and feedback, and conduct preliminary tests to validate that the needle is accurately controlled by the robotic arm. Testing with different mediums such as gel or phantom tissue, and eventually animal experiments will follow in a future publication due to time constraints.
ContributorsNienhouse, Lucas (Author) / Marvi, Hamidreza (Thesis director) / Lee, Hyunglae (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor) / School of Mathematical and Statistical Sciences (Contributor)
Created2022-05
Description
As the explorations beyond the Earth's boundaries continue to evolve, researchers and engineers strive to develop versatile technologies capable of adapting to unknown space conditions. For instance, the utilization of Screw-Propelled Vehicles (SPVs) and robotics that utilize helical screws propulsion to transverse planetary bodies is a growing area of interest. An example of such technology is the Extant Exobiology Life Surveyor (EELS), a snake-like robot currently developed by the NASA Jet Propulsion Laboratory (JPL) to explore the surface of Saturn’s moon, Enceladus. However, the utilization of such a mechanism requires a deep and thorough understanding of screw mobility in uncertain conditions. The main approach to exploring screw dynamics and optimal design involves the utilization of Discrete Element Method (DEM) simulations to assess interactions and behavior of screws when interacting with granular terrains. In this investigation, the Simplified Johnson-Kendall-Roberts (SJKR) model is implemented into the utilized simulation environment to account for cohesion effects similar to what is experienced on celestial bodies like Enceladus. The model is verified and validated through experimental and theoretical testing. Subsequently, the performance characteristics of screws are explored under varying parameters, such as thread depth, number of screw starts, and the material’s cohesion level. The study has examined significant relationships between the parameters under investigation and their influence on the screw performance.
ContributorsAbdelrahim, Mohammad (Author) / Marvi, Hamid (Thesis advisor) / Berman, Spring (Committee member) / Lee, Hyunglae (Committee member) / Arizona State University (Publisher)
Created2023
Description
Soft robotics has garnered attention for its substantial prospective in various domains, such as manipulation and interactions with humans, by offering competitive advantages against rigid robotic systems, including inherent compliance and variable stiffness. Despite these benefits, their theoretically infinite degrees of freedom and prominent nonlinearities pose significant challenges in developing dynamic models and guiding the robots along desired paths. Additionally, soft robots may exhibit rigid behaviors and potentially collide with their surroundings during path tracking tasks, particularly when possible contact points are unknown. In this dissertation, reduced-order models are used to describe the behaviors of three different soft robot designs, including both linear parameter varying (LPV) and augmented rigid robot (ARR) models. While the reduced-order model captures the majority of the soft robot's dynamics, modeling uncertainties notably remain. Non-repeated modeling uncertainties are addressed by categorizing them as a lumped disturbance, employing two methodologies, $H_\infty$ method and nonlinear disturbance observer (NDOB) based sliding mode control, for its rejection. For repeated disturbances, an iterative learning control (ILC) with a P-type learning function is implemented to enhance trajectory tracking efficacy. Furthermore,for non-repeated disturbances, the NDOB facilitates the contact estimation, and its results are jointly used with a switching algorithm to modify the robot trajectories. The stability proof of all controllers and corresponding simulation and experimental results are provided. For a path tracking task of a soft robot with multi-segments, a robust control strategy that combines a LPV model with an innovative improved nonlinear disturbance observer-based adaptive sliding mode control (INASMC). The control framework employs a first-order LPV model for dynamic representation, leverages an improved disturbance observer for accurate disturbance forecasting, and utilizes adaptive sliding mode control to effectively counteract uncertainties. The tracking error under the proposed controller is proven to be asymptotically stable, and the controller's effectiveness is is validated with simulation and experimental results. Ultimately, this research mitigates the inherent uncertainty in soft robot modeling, thereby enhancing their functionality in contact-intensive tasks.
ContributorsQIAO, ZHI (Author) / Zhang, Wenlong (Thesis advisor) / Marvi, Hamidreza (Committee member) / Lee, Hyunglae (Committee member) / Berman, Spring (Committee member) / Sugar, Thomas (Committee member) / Arizona State University (Publisher)
Created2023