Matching Items (31)
Filtering by
- All Subjects: Electrical Engineering
- Genre: Doctoral Dissertation
- Creators: Kitchen, Jennifer
Description
Radio frequency (RF) transceivers require a disproportionately high effort in terms of test development time, test equipment cost, and test time. The relatively high test cost stems from two contributing factors. First, RF transceivers require the measurement of a diverse set of specifications, requiring multiple test set-ups and long test times, which complicates load-board design, debug, and diagnosis. Second, high frequency operation necessitates the use of expensive equipment, resulting in higher per second test time cost compared with mixed-signal or digital circuits. Moreover, in terms of the non-recurring engineering cost, the need to measure complex specfications complicates the test development process and necessitates a long learning process for test engineers. Test time is dominated by changing and settling time for each test set-up. Thus, single set-up test solutions are desirable. Loop-back configuration where the transmitter output is connected to the receiver input are used as the desirable test set- up for RF transceivers, since it eliminates the reliance on expensive instrumentation for RF signal analysis and enables measuring multiple parameters at once. In-phase and Quadrature (IQ) imbalance, non-linearity, DC offset and IQ time skews are some of the most detrimental imperfections in transceiver performance. Measurement of these parameters in the loop-back mode is challenging due to the coupling between the receiver (RX) and transmitter (TX) parameters. Loop-back based solutions are proposed in this work to resolve this issue. A calibration algorithm for a subset of the above mentioned impairments is also presented. Error Vector Magnitude (EVM) is a system-level parameter that is specified for most advanced communication standards. EVM measurement often takes extensive test development efforts, tester resources, and long test times. EVM is analytically related to system impairments, which are typically measured in a production test i environment. Thus, EVM test can be eliminated from the test list if the relations between EVM and system impairments are derived independent of the circuit implementation and manufacturing process. In this work, the focus is on the WLAN standard, and deriving the relations between EVM and three of the most detrimental impairments for QAM/OFDM based systems (IQ imbalance, non-linearity, and noise). Having low cost test techniques for measuring the RF transceivers imperfections and being able to analytically compute EVM from the measured parameters is a complete test solution for RF transceivers. These techniques along with the proposed calibration method can be used in improving the yield by widening the pass/fail boundaries for transceivers imperfections. For all of the proposed methods, simulation and hardware measurements prove that the proposed techniques provide accurate characterization of RF transceivers.
ContributorsNassery, Afsaneh (Author) / Ozev, Sule (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kiaei, Sayfe (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2013
Description
The world has seen a revolution in cellular communication with the advent of 5G, which enables gigabits per second data speed with low latency, massive capacity, and increased availability. Complex modulated signals are used in these moderncommunication systems to achieve high spectral efficiency, and these signals exhibit high peak to average power ratios (PAPR). Design of cellular infrastructure hardware to support these complex signals therefore becomes challenging, as the transmitter’s radio frequency power amplifier (RF PA) needs to remain highly efficient at both peak and backed off power conditions. Additionally, these PAs should exhibit high linearity and support continually increasing bandwidths. Many advanced PA configurations exhibit high efficiency for processing legacy communications signals. Some of the most popular architectures are Envelope Elimination and Restoration (EER), Envelope Tracking (ET), Linear Amplification using Non-linear Component (LINC), Doherty Power Amplifiers (DPA), and Polar Transmitters. Among these techniques,
the DPA is the most widely used architecture for base-station applications because of its simple configuration and ability to be linearized using simple digital pre-distortion (DPD) algorithms. To support the cellular infrastructure needs of 5G and beyond, RF PAs, specifically DPA architectures, must be further enhanced to support broader bandwidths as well as smaller form-factors with higher levels of integration. The following four novel works are presented in this dissertation to support RF PA requirements for future cellular infrastructure:
1. A mathematical analysis to analyze the effects of non-linear parasitic capacitance (Cds) on the operation of continuous class-F (CCF) mode power amplifiers and identify their optimum operating range for high power and efficiency.
2. A methodology to incorporate a class-J harmonic trapping network inside the PA package by considering the effect of non-linear Cds, thus reducing the DPA footprint while achieving high RF performance.
3. A novel method of synthesizing the DPA’s output combining network (OCN) to realize an integrated two-stage integrated LDMOS asymmetric DPA.
4. A novel extended back-off efficiency range DPA architecture that engineers the mutual interaction between combining load and peaking off-state impedance. The theory and architecture are verified through a GaN-based DPA design.
ContributorsAhmed, Maruf Newaz (Author) / Kitchen, Jennifer (Thesis advisor) / Aberle, James (Committee member) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2022
Description
Impedance is one of the fundamental properties of electrical components, materials, and waves. Therefore, impedance measurement and monitoring have a wide range of applications. The multi-port technique is a natural candidate for impedance measurement and monitoring due to its low overhead and ease of implementation for Built-in Self-Test (BIST) applications. The multi-port technique can measure complex reflection coefficients, thus impedance, by using scalar measurements provided by the power detectors. These power detectors are strategically placed on different points (ports) of a passive network to produce unique solution. Impedance measurement and monitoring is readily deployed on mobile phone radio-frequency (RF) front ends, and are combined with antenna tuners to boost the signal reception capabilities of phones. These sensors also can be used in self-healing circuits to improve their yield and performance under process, voltage, and temperature variations. Even though, this work is preliminary interested in low-overhead impedance measurement for RF circuit applications, the proposed methods can be used in a wide variety of metrology applications where impedance measurements are already used. Some examples of these applications include determining material properties, plasma generation, and moisture detection. Additionally, multi-port applications extend beyond the impedance measurement. There are applications where multi-ports are used as receivers for communication systems, RADARs, and remote sensing applications. The multi-port technique generally requires a careful design of the testing structure to produce a unique solution from power detector measurements. It also requires the use of nonlinear solvers during calibration, and depending on calibration procedure, measurement. The use of nonlinear solvers generates issues for convergence, computational complexity, and resources needed for carrying out calibrations and measurements in a timely manner. In this work, using periodic structures, a structure where a circuit block repeats itself, for multi-port measurements is proposed. The periodic structures introduce a new constraint that simplifies the multi-port theory and leads to an explicit calibration and measurement procedure. Unlike the existing calibration procedures which require at least five loads and various constraints on the load for explicit solution, the proposed method can use three loads for calibration. Multi-ports built with periodic structures will always produce a unique measurement result. This leads to increased bandwidth of operation and simplifies design procedure. The efficacy of the method demonstrated in two embodiments.
In the first embodiment, a multi-port is directly embedded into a matching network to measure impedance of the load.
In the second embodiment, periodic structures are used to compare two loads without requiring any calibration.
ContributorsAvci, Muslum Emir (Author) / Ozev, Sule (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2023
Description
Modern-day automobiles are becoming more connected and reliant on wireless connectivity. Thus, automotive electronics can be both a cause of and highly sensitive to electromagnetic interference (EMI), and the consequences of failure can be fatal. Technology advancements in engineering have brought several features into the automotive field but at the expense of electromagnetic compatibility issues. Automotive EMC problems are the result of the emissions from electronic assemblies inside a vehicle and the susceptibility of the electronics when exposed to external EMI sources. In both cases, automotive EMC problems can cause unintended changes in the automotive system operation. Robustness to electromagnetic interference (EMI) is one of the primary design aspects of state-of-the-art automotive ICs like System Basis Chips (SBCs) which provide a wide range of analog, power regulation and digital functions on the same die. One of the primary sources of conducted EMI on the Local Interconnect Network (LIN) driver output is an integrated switching DC-DC regulator noise coupling through the parasitic substrate capacitance of the SBC. In this dissertation an adaptive active EMI cancellation technique to cancel the switching noise of the DC-DC regulator on the LIN driver output to ensure electromagnetic compatibility (EMC) is presented. The proposed active EMI cancellation circuit synthesizes a phase synchronized cancellation pulse which is then injected onto the LIN driver output using an on-chip tunable capacitor array to cancel the switching noise injected via the substrate. The proposed EMI reduction technique can track and cancel substrate noise independent of process technology and device parasitics, input voltage, duty cycle, and loading conditions of the DC-DC switching regulator. The EMI cancellation system is designed and fabricated on a 180nm Bipolar-CMOS-DMOS (BCD) process with an integrated power stage of a DC-DC buck regulator at a switching frequency of 2MHz along with an automotive LIN driver. The EMI cancellation circuit occupies an area of 0.7 mm2, which is less than 3% of the overall area in a standard SBC and consumes 12.5 mW of power and achieves 25 dB reduction of conducted EMI in the LIN driver output’s power spectrum at the switching frequency and its harmonics.
ContributorsRay, Abhishek (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Kitchen, Jennifer (Committee member) / Seo, Jae-Sun (Committee member) / Arizona State University (Publisher)
Created2023
Description
The development of portable electronic systems has been a fundamental factor to the emergence of new applications including ubiquitous smart devices, self-driving vehicles. Power-Management Integrated Circuits (PMICs) which are a key component of such systems must maintain high efficiency and reliability for the final system to be appealing from a size and cost perspective. As technology advances, such portable systems require high output currents at low voltages from their PMICs leading to thermal reliability concerns. The reliability and power integrity of PMICs in such systems also degrades when operated in harsh environments. This dissertation presents solutions to solve two such reliability problems.The first part of this work presents a scalable, daisy-chain solution to parallelize multiple low-dropout linear (LDO) regulators to increase the total output current at low voltages. This printed circuit board (PCB) friendly approach achieves output current sharing without the need for any off-chip active or passive components or matched PCB traces thus reducing the overall system cost. Fully integrated current sensing based on dynamic element matching eliminates the need for any off-chip current sensing components. A current sharing accuracy of 2.613% and 2.789% for output voltages of 3V and 1V respectively and an output current of 2A per LDO are measured for the parallel LDO system implemented in a 0.18μm process. Thermal images demonstrate that the parallel LDO system achieves thermal equilibrium and stable reliable operation.
The remainder of the thesis deals with time-domain switching regulators for high-reliability applications. A time-domain based buck and boost controller with time as the processing variable is developed for use in harsh environments. The controller features adaptive on-time / off-time generation for quasi-constant switching frequency and a time-domain comparator to implement current-mode hysteretic control. A triple redundant bandgap reference is also developed to mitigate the effects of radiation. Measurement results are showcased for a buck and boost converter with a common controller IC implemented in a 0.18μm process and an external power stage. The converter achieves a peak efficiency of 92.22% as a buck for an output current of 5A and an output voltage of 5V. Similarly, the converter achieves an efficiency of 95.97% as a boost for an output current of 1.25A and an output voltage of 30.4V.
ContributorsTalele, Bhushan (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Seo, Jae-Sun (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2021
Description
In this dissertation, enhanced coherent detection of terahertz (THz) radiation is presented for Silicon integrated circuits (ICs). In general THz receivers implemented in silicon technologies face a challenge due to the high noise figure (NF) of the low noise amplifier (LNA) and low conversion gain of the radio frequency (RF) mixers. Moreover, issues with implementing local oscillators (LOs) further compound these challenges, including power driving mixes, distribution networks, and overall power consumption, particularly for large-scale arrays. To address these inherent obstacles, two notable cases of enhancing THz receiver performance are presented. In the Sideband Separation Receiver (SSR) for space-borne applications is introduced. Implemented in SiGe BiCMOS technology this broadband SSR boasts a high Image Rejection Ratio (IRR) exceeding 20 dB across 220 – 320 GHz. Employing a modified Weaver architecture, optimized for simultaneous spectral line observation, it utilizes an I/Q double down-conversion, pushing the technological boundaries of silicon and enabling large-scale focal plane array (FPA) deployment in space. Notably, the use of a sub-harmonic down-conversion mixer (SHM) significantly reduces LO power generation challenges, enhancing scalability while maintaining minimal NF.
In the 4x4 FPA active THz imager, a dual-polarized patch antenna operating at 420 GHz utilizes orthogonal polarization for RF and LO signals, coupled with a coherent homodyne power detector. Realized in 0.13µm SiGe HBT technology, the power detector is co-designing with the antenna to ensure minimal crosstalk and achieving -30dB cross-polarization isolation. Illumination of the LO enhances power detector performance without on-chip routing complexities, enabling scalability to 1K pixel THz imagers. Each pixel achieves a Noise-Equivalent Power (NEP) of 1 pW/√Hz at 420 GHz, and integration with a readout and digital filter ensures high dynamic range.
Furthermore, this study explores radiation hardening techniques to mitigate single-event effects (SEEs) in high-frequency receivers operating in space. Leveraging a W-band receiver in 90 nm SiGe BiCMOS technology, matching considerations and diverse modes of operation are employed to reduce SEE susceptibility. Transient current pulse modeling, validated through TCAD simulations, demonstrates the effectiveness of proposed techniques in substantially mitigating SETs within the proposed radiation-hardened-by-design (RHBD) receiver front-end.
ContributorsAl Seragi, Ebrahim (Author) / Zeinolabedinzadeh, Saeed (Thesis advisor) / Trichopoulos, Georgios (Committee member) / Bakkaloglu, Bertan (Committee member) / Aberle, James (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2024
Description
The world has seen a revolution in cellular communication with the advent of 5G (fifth-generation), which enables gigabits per second data speed with low latency, massive capacity, and increased availability. These modern wireless systems improve spectrum efficiency by employing advanced modulation techniques, but result in large peak-to-average power ratios (PAPR) of the transmitted signals that degrades the efficiency of the radio-frequency power amplifiers (PAs) in the power back-off (PBO) region. Envelope tracking (ET), which is a dynamic supply control technology to realize high efficiency PAs, is a promising approach for designing transmitters for the future. Conventional voltage regulators, such as linear regulators and switching regulators, fail to simultaneously offer high speed, high efficiency, and improved linearity. Hybrid supply modulators (HSM) that combine a linear and switching regulator emerge as promising solutions to achieve an optimized tradeoff between different design parameters. Over the years, considerable development and research efforts in industry and academia have been spent on maximizing HSM performance, and a majority of the most recently developed modulators are implemented in CMOS technology and mainly targeted for handset applications. In this dissertation, the main requirements for modern HSM designs are categorized and analyzed in detail. Next, techniques to improve HSM performance are discussed. The available device technologies for HSM and PA implementations are also delineated, and implementation challenges of an integrated ET-PA system are summarized. Finally, a Current-Mode with Dynamic Hysteresis HSM is proposed, designed, and implemented. With the proposed technique, the HSM is able to track LTE signals up to 100 MHz bandwidth. Switching at a peak frequency of 40 MHz, the design is able to track a 1 Vpp sinusoidal signal with high fidelity, has an output voltage ripple around 54 mV, and achieves a peak static and dynamic efficiency of 92.2% and 82.29%, respectively, at the maximum output. The HSM is capable of delivering a maximum output power of 425 mW and occupies a small die area of 1.6mm2. Overall, the proposed HSM promises competitive performance compared to state-of-the-art works.
ContributorsBHARDWAJ, SUMIT (Author) / Kitchen, Jennifer (Thesis advisor) / Ozev, Sule (Committee member) / Bakkaloglu, Bertan (Committee member) / Singh, Shrikant (Committee member) / Arizona State University (Publisher)
Created2024
Description
Handheld devices and personal laptops are becoming compact and complex every year with a demand to have higher power density, efficiency, and fast transient response. DC-DC boost converters are used in display and haptic drivers where the output voltage needs to be boosted higher than input voltage. The load transient response and unity gain bandwidth (UGB) of DC-DC boost converters are restricted by the presence of a right half plane zero (RHPZ). In this paper, a control scheme termed peak current fast feedback control (PFFC) is proposed to improve the load transient response without the need for additional power switches or passive components. The fast feedback (FFB) path is designed to achieve low output voltage change and fast settling time with the same UGB when compared to the conventional peak current mode control (CPCM). In the proposed PFFC method, the closed loop output impedance (ZOCL) is improved by reducing the DC value and by increasing the bandwidth of ZOCL as compared to conventional peak current mode control (CPCM), thus improving the steady state and transient performance. The fast feedback (FFB) path is implemented within the error amplifier (EA) with an increase of only 2% in the active area as compared to CPCM. The boost converter is designed for VOUT=5V, VIN=2.5V-4.4V and ILOAD=10mA-1A operating at a frequency of 2MHz. Measurement results show that with PFFC enabled, the settling time reduces by ~2.6X and the undershoot reduces by 62% to 12μs and 41mV respectively when compared to CPCM for 10mA to 1A load step at 2A/μs. The PFFC approach improves the settling time by 12X to 26us and reduces the overshoot by 56% to 56mV when compared to CPCM for 1A to 10mA load step at 2A/μs. The converter achieves a peak efficiency of 95.2% at 0.5W output power with VIN=4.4V and load regulation of 9mV/A at VIN=2.5V. The line transient response at VOUT=5V, ILOAD=700mA for VIN=3V ↔ 4V which is repeated at 280μs time period is 235mV and 245mV for CPCM and PFFC respectively.
ContributorsAlevoor, Shashank (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Sanyal, Arindham (Committee member) / Beohar, Navankur (Committee member) / Arizona State University (Publisher)
Created2023
Description
Recent advancements in communication standards, such as 5G demand transmitter hardware to support high data rates with high energy efficiency. With the revolution of communication standards, modulation schemes have become more complex and require high peak-to-average (PAPR) signals. In wireless transceiver hardware, the power amplifier (PA) consumes most of the transceiver’s DC power and is typically the bottleneck for transmitter linearity. Therefore, the transmitter’s performance directly depends on the PA. To support high PAPR signals, the PA must operate efficiently at its saturated and backoff output power. Maintaining high efficiency at both peak and backoff output power is challenging. One effective technique for addressing this problem is load modulation. Some of the prominent load-modulated PA architectures are outphasing PAs, load-modulated balanced amplifiers (LMBA), envelope elimination and restoration (EER), envelope tracking (ET), Doherty power amplifiers (DPA), and polar transmitters. Amongst them, the DPA is the most popular for infrastructure applications due to its simpler architecture compared to other techniques and linearizability with digital pre-distortion (DPD). Another crucial characteristic of progressing communication standards is wide signal bandwidths. High-efficiency power amplifiers like class J/F/F-1 and load-modulated PAs like the DPA exhibit narrowband performance because the amplifiers require precise output impedance terminations. Therefore, it is equally essential to develop adaptable PA solutions to process radio frequency (RF) signals with wide bandwidths. To support modern and future cellular infrastructure, RF PAs need to be innovated to increase the backoff power efficiency by two times or more and support ten times or more wider bandwidths than current state-of-the-art PAs. This work presents five RF PA analyses and implementations to support future wireless communications transmitter hardware. Chapter 2 presents an optimized output-matching network analysis and design to achieve extended output power backoff of the DPA. Chapters 3 and 4 unveil two bandwidth enhancement techniques for the DPA while maintaining extended output power backoff. Chapter 5 exhibits a dual-band hybrid mode PA design targeted for wideband applications. Chapter 6 presents a built-in self-test circuit integrated into a PA for output impedance monitoring. This can alleviate the PA performance degradation due to the variation in the PA's output load over frequency, process, and aging. All RF PAs in this dissertation are implemented using Gallium Nitride (GaN)-based high electron mobility transistors (HEMT), and the realized designs validate the proposed PAs' theories/architectures.
ContributorsRoychowdhury, Debatrayee (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Aberle, James (Committee member) / Arizona State University (Publisher)
Created2024
Description
This dissertation proposes and presents two different passive sigma-delta
modulator zoom Analog to Digital Converter (ADC) architectures. The first ADC is fullydifferential, synthesizable zoom-ADC architecture with a passive loop filter for lowfrequency Built in Self-Test (BIST) applications. The detailed ADC architecture and a step
by step process designing the zoom-ADC along with a synthesis tool that can target various
design specifications are presented. The design flow does not rely on extensive knowledge
of an experienced ADC designer. Two example set of BIST ADCs have been synthesized
with different performance requirements in 65nm CMOS process. The first ADC achieves
90.4dB Signal to Noise Ratio (SNR) in 512µs measurement time and consumes 17µW
power. Another example achieves 78.2dB SNR in 31.25µs measurement time and
consumes 63µW power. The second ADC architecture is a multi-mode, dynamically
zooming passive sigma-delta modulator. The architecture is based on a 5b interpolating
flash ADC as the zooming unit, and a passive discrete time sigma delta modulator as the
fine conversion unit. The proposed ADC provides an Oversampling Ratio (OSR)-
independent, dynamic zooming technique, employing an interpolating zooming front-end.
The modulator covers between 0.1 MHz and 10 MHz signal bandwidth which makes it
suitable for cellular applications including 4G radio systems. By reconfiguring the OSR,
bias current, and component parameters, optimal power consumption can be achieved for
every mode. The ADC is implemented in 0.13 µm CMOS technology and it achieves an
SNDR of 82.2/77.1/74.2/68 dB for 0.1/1.92/5/10MHz bandwidth with 1.3/5.7/9.6/11.9mW
power consumption from a 1.2 V supply.
modulator zoom Analog to Digital Converter (ADC) architectures. The first ADC is fullydifferential, synthesizable zoom-ADC architecture with a passive loop filter for lowfrequency Built in Self-Test (BIST) applications. The detailed ADC architecture and a step
by step process designing the zoom-ADC along with a synthesis tool that can target various
design specifications are presented. The design flow does not rely on extensive knowledge
of an experienced ADC designer. Two example set of BIST ADCs have been synthesized
with different performance requirements in 65nm CMOS process. The first ADC achieves
90.4dB Signal to Noise Ratio (SNR) in 512µs measurement time and consumes 17µW
power. Another example achieves 78.2dB SNR in 31.25µs measurement time and
consumes 63µW power. The second ADC architecture is a multi-mode, dynamically
zooming passive sigma-delta modulator. The architecture is based on a 5b interpolating
flash ADC as the zooming unit, and a passive discrete time sigma delta modulator as the
fine conversion unit. The proposed ADC provides an Oversampling Ratio (OSR)-
independent, dynamic zooming technique, employing an interpolating zooming front-end.
The modulator covers between 0.1 MHz and 10 MHz signal bandwidth which makes it
suitable for cellular applications including 4G radio systems. By reconfiguring the OSR,
bias current, and component parameters, optimal power consumption can be achieved for
every mode. The ADC is implemented in 0.13 µm CMOS technology and it achieves an
SNDR of 82.2/77.1/74.2/68 dB for 0.1/1.92/5/10MHz bandwidth with 1.3/5.7/9.6/11.9mW
power consumption from a 1.2 V supply.
ContributorsEROL, OSMAN EMIR (Author) / Ozev, Sule (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ogras, Umit Y. (Committee member) / Blain-Christen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2018