Matching Items (11)
Filtering by
- All Subjects: Electrical Engineering
- Genre: Masters Thesis
Description
Fluxgate sensors are magnetic field sensors that can measure DC and low frequency AC magnetic fields. They can measure much lower magnetic fields than other magnetic sensors like Hall effect sensors, magnetoresistive sensors etc. They also have high linearity, high sensitivity and low noise. The major application of fluxgate sensors is in magnetometers for the measurement of earth's magnetic field. Magnetometers are used in navigation systems and electronic compasses. Fluxgate sensors can also be used to measure high DC currents. Integrated micro-fluxgate sensors have been developed in recent years. These sensors have much lower power consumption and area compared to their PCB counterparts. The output voltage of micro-fluxgate sensors is very low which makes the analog front end more complex and results in an increase in power consumption of the system. In this thesis a new analog front-end circuit for micro-fluxgate sensors is developed. This analog front-end circuit uses charge pump based excitation circuit and phase delay based read-out chain. With these two features the power consumption of analog front-end is reduced. The output is digital and it is immune to amplitude noise at the output of the sensor. Digital output is produced without using an ADC. A SPICE model of micro-fluxgate sensor is used to verify the operation of the analog front-end and the simulation results show very good linearity.
ContributorsPappu, Karthik (Author) / Bakkaloglu, Bertan (Thesis advisor) / Christen, Jennifer Blain (Committee member) / Yu, Hongbin (Committee member) / Arizona State University (Publisher)
Created2013
Description
Coarse Grain Reconfigurable Arrays (CGRAs) are promising accelerators capable of
achieving high performance at low power consumption. While CGRAs can efficiently
accelerate loop kernels, accelerating loops with control flow (loops with if-then-else
structures) is quite challenging. Techniques that handle control flow execution in
CGRAs generally use predication. Such techniques execute both branches of an
if-then-else structure and select outcome of either branch to commit based on the
result of the conditional. This results in poor utilization of CGRA s computational
resources. Dual-issue scheme which is the state of the art technique for control flow
fetches instructions from both paths of the branch and selects one to execute at
runtime based on the result of the conditional. This technique has an overhead in
instruction fetch bandwidth. In this thesis, to improve performance of control flow
execution in CGRAs, I propose a solution in which the result of the conditional
expression that decides the branch outcome is communicated to the instruction fetch
unit to selectively issue instructions from the path taken by the branch at run time.
Experimental results show that my solution can achieve 34.6% better performance
and 52.1% improvement in energy efficiency on an average compared to state of the
art dual issue scheme without imposing any overhead in instruction fetch bandwidth.
achieving high performance at low power consumption. While CGRAs can efficiently
accelerate loop kernels, accelerating loops with control flow (loops with if-then-else
structures) is quite challenging. Techniques that handle control flow execution in
CGRAs generally use predication. Such techniques execute both branches of an
if-then-else structure and select outcome of either branch to commit based on the
result of the conditional. This results in poor utilization of CGRA s computational
resources. Dual-issue scheme which is the state of the art technique for control flow
fetches instructions from both paths of the branch and selects one to execute at
runtime based on the result of the conditional. This technique has an overhead in
instruction fetch bandwidth. In this thesis, to improve performance of control flow
execution in CGRAs, I propose a solution in which the result of the conditional
expression that decides the branch outcome is communicated to the instruction fetch
unit to selectively issue instructions from the path taken by the branch at run time.
Experimental results show that my solution can achieve 34.6% better performance
and 52.1% improvement in energy efficiency on an average compared to state of the
art dual issue scheme without imposing any overhead in instruction fetch bandwidth.
ContributorsRajendran Radhika, Shri Hari (Author) / Shrivastava, Aviral (Thesis advisor) / Christen, Jennifer Blain (Committee member) / Cao, Yu (Committee member) / Arizona State University (Publisher)
Created2014
Description
The past two decades have been monumental in the advancement of microchips designed for a diverse range of medical applications and bio-analysis. Owing to the remarkable progress in micro-fabrication technology, complex chemical and electro-mechanical features can now be integrated into chip-scale devices for use in biosensing and physiological measurements. Some of these devices have made enormous contributions in the study of complex biochemical processes occurring at the molecular and cellular levels while others overcame the challenges of replicating various functions of human organs as implant systems. This thesis presents test data and analysis of two such systems. First, an ISFET based pH sensor is characterized for its performance in a continuous pH monitoring application. Many of the basic properties of ISFETs including I-V characteristics, pH sensitivity and more importantly, its long term drift behavior have been investigated. A new theory based on frequent switching of electric field across the gate oxide to decrease the rate of current drift has been successfully implemented with the help of an automated data acquisition and switching system. The system was further tested for a range of duty cycles in order to accurately determine the minimum length of time required to fully reset the drift. Second, a microfluidic based vestibular implant system was tested for its underlying characteristics as a light sensor. A computer controlled tilt platform was then implemented to further test its sensitivity to inclinations and thus it‟s more important role as a tilt sensor. The sensor operates through means of optoelectronics and relies on the signals generated from photodiode arrays as a result of light being incident on them. ISFET results show a significant drop in the overall drift and good linear characteristics. The drift was seen to reset at less than an hour. The photodiodes show ideal I-V comparison between photoconductive and photovoltaic modes of operation with maximum responsivity at 400nm and a shunt resistance of 394 MΩ. Additionally, post-processing of the tilt sensor to incorporate the sensing fluids is outlined. Based on several test and fabrication results, a possible method of sealing the open cavity of the chip using a UV curable epoxy has been discussed.
ContributorsMamun, Samiha (Author) / Christen, Jennifer Blain (Thesis advisor) / Goryll, Michael (Committee member) / Yu, Hongyu (Committee member) / Arizona State University (Publisher)
Created2011
Description
Due to heterogeneity at the cellular level, single cell analysis (SCA) has become a necessity to study cellomics for the early detection of diseases like cancer. Development of single cell manipulation systems is very critical for performing SCA. In this thesis, electrorotation (ROT) chips to trap and rotate single cells using electrokinetic forces have been developed. The ROT chip mainly consists of a set of closely spaced metal electrodes (60µm interspacing between opposite electrodes) that forms a closed electric field cage (electrocage) when driven with high frequency AC voltages. Cells were flowed through a microchannel to the electrocage where they could be precisely trapped, levitated and rotated in 3-D along the axis of interest. The dielectrophoresis based ROT chip design and relevant electrokinetic effects have been simulated using COMSOL 3.4 to optimize the design parameters. Also, various semiconductor technology fabrication process steps have been developed and optimized for better yield and repeatability in the manufacture of the ROT chip. The ROT chip thus fabricated was used to characterize rotation of single cells with respect to the control parameters namely excitation voltage, frequency and cell line. The longevity of cell rotation under electric fields has been probed. Also, the Joule heating inside the ROT chip due to applied voltage has been characterized to know the thermal stress on the cells. The major advantages of the ROT chip developed are precise electrorotation of cells, simple design and straight forward fabrication process.
ContributorsSoundappa Elango, Iniyan (Author) / Meldrum, Deirdre R (Thesis advisor) / Christen, Jennifer Blain (Committee member) / Johnson, Roger H (Committee member) / Arizona State University (Publisher)
Created2012
Description
The front end of almost all ADCs consists of a Sample and Hold Circuit in order to make sure a constant analog value is digitized at the end of ADC. The design of Track and Hold Circuit (THA) mainly focuses on following parameters: Input frequency, Sampling frequency, dynamic Range, hold pedestal, feed through error. This thesis will discuss the importance of these parameters of a THA to the ADCs and commonly used architectures of THA. A new architecture with SiGe HBT transistors in BiCMOS 130 nm technology is presented here. The proposed topology without complicated circuitry achieves high Spurious Free Dynamic Range(SFDR) and Total Harmonic Distortion (THD).These are important figure of merits for any THA which gives a measure of non-linearity of the circuit. The proposed topology is implemented in IBM8HP 130 nm BiCMOS process combines typical emitter follower switch in bipolar THAs and output steering technique proposed in the previous work. With these techniques and the cascode transistor in the input which is used to isolate the switch from the input during the hold mode, better results have been achieved. The THA is designed to work with maximum input frequency of 250 MHz at sampling frequency of 500 MHz with input currents not more than 5mA achieving an SFDR of 78.49 dB. Simulation and results are presented, illustrating the advantages and trade-offs of the proposed topology.
ContributorsRao, Nishita Ramakrishna (Author) / Barnaby, Hugh (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2012
Description
Flexible hybrid electronics (FHE) is emerging as a promising solution to combine the benefits of printed electronics and silicon technology. FHE has many high-impact potential areas, such as wearable applications, health monitoring, and soft robotics, due to its physical advantages, which include light weight, low cost and the ability conform to different shapes. However, physical deformations that can occur in the field lead to significant testing and validation challenges. For example, designers have to ensure that FHE devices continue to meet specs even when the components experience stress due to bending. Hence, physical deformation, which is hard to emulate, has to be part of the test procedures developed for FHE devices. This paper is the first to analyze stress experience at different parts of FHE devices under different bending conditions. Then develop a novel methodology to maximize the test coverage with minimum number of text vectors with the help of a mixed integer linear programming formulation.
ContributorsGao, Hang (Author) / Ozev, Sule (Thesis advisor) / Ogras, Umit Y. (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2018
Description
Intracranial pressure is an important parameter to monitor, and elevated intracranial pressure can be life threatening. Elevated intracranial pressure is indicative of distress in the brain attributed by conditions such as aneurysm, traumatic brain injury, brain tumor, hydrocephalus, stroke, or meningitis.
Electrocorticography (ECoG) recordings are invaluable in understanding epilepsy and detecting seizure zones. However, ECoG electrodes cause a foreign body mass effect, swelling, and pneumocephaly, which results in elevation of intracranial pressure (ICP). Thus, the aim of this work is to design an intracranial pressure monitoring system that could augment ECoG electrodes.
A minimally invasive, low-cost epidural intracranial pressure monitoring system is developed for this purpose, using a commercial pressure transducer available for biomedical applications. The system is composed of a pressure transducer, sensing cup, electronics, and data acquisition system. The pressure transducer is a microelectromechanical system (MEMS)-based die that works on piezoresistive phenomenon with dielectric isolation for direct contact with fluids.
The developed system was bench tested and verified in an animal model to confirm the efficacy of the system for intracranial pressure monitoring. The system has a 0.1 mmHg accuracy and a 2% error for the 0-10 mmHg range, with resolution of 0.01 mmHg. This system serves as a minimally invasive (2 mm burr hole) epidural ICP monitor, which could augment existing ECoG electrode arrays, to simultaneously measure intracranial pressure along with the neural signals.
This device could also be employed with brain implants that causes elevation in ICP due to tissue - implant interaction often leading to edema. This research explores the concept and feasibility for integrating the sensing component directly on to the ECoG electrode arrays.
Electrocorticography (ECoG) recordings are invaluable in understanding epilepsy and detecting seizure zones. However, ECoG electrodes cause a foreign body mass effect, swelling, and pneumocephaly, which results in elevation of intracranial pressure (ICP). Thus, the aim of this work is to design an intracranial pressure monitoring system that could augment ECoG electrodes.
A minimally invasive, low-cost epidural intracranial pressure monitoring system is developed for this purpose, using a commercial pressure transducer available for biomedical applications. The system is composed of a pressure transducer, sensing cup, electronics, and data acquisition system. The pressure transducer is a microelectromechanical system (MEMS)-based die that works on piezoresistive phenomenon with dielectric isolation for direct contact with fluids.
The developed system was bench tested and verified in an animal model to confirm the efficacy of the system for intracranial pressure monitoring. The system has a 0.1 mmHg accuracy and a 2% error for the 0-10 mmHg range, with resolution of 0.01 mmHg. This system serves as a minimally invasive (2 mm burr hole) epidural ICP monitor, which could augment existing ECoG electrode arrays, to simultaneously measure intracranial pressure along with the neural signals.
This device could also be employed with brain implants that causes elevation in ICP due to tissue - implant interaction often leading to edema. This research explores the concept and feasibility for integrating the sensing component directly on to the ECoG electrode arrays.
ContributorsSampath Kumaran, Ranjani (Author) / Christen, Jennifer Blain (Thesis advisor) / Tillery, Stephen Helms (Committee member) / Greger, Bradley (Committee member) / Arizona State University (Publisher)
Created2015
Description
Alternative computation based on neural systems on a nanoscale device are of increasing interest because of the massive parallelism and scalability they provide. Neural based computation systems also offer defect finding and self healing capabilities. Traditional Von Neumann based architectures (which separate the memory and computation units) inherently suffer from the Von Neumann bottleneck whereby the processor is limited by the number of instructions it fetches. The clock driven based Von Neumann computer survived because of technology scaling. However as transistor scaling is slowly coming to an end with channel lengths becoming a few nanometers in length, processor speeds are beginning to saturate. This lead to the development of multi-core systems which process data in parallel, with each core being based on the Von Neumann architecture.
The human brain has always been a mystery to scientists. Modern day super computers are outperformed by the human brain in certain computations. The brain occupies far less space and consumes a fraction of the power a super computer does with certain processes such as pattern recognition. Neuromorphic computing aims to mimic biological neural systems on silicon to exploit the massive parallelism that neural systems offer. Neuromorphic systems are event driven systems rather than being clock driven. One of the issues faced by neuromorphic computing was the area occupied by these circuits. With recent developments in the field of nanotechnology, memristive devices on a nanoscale have been developed and show a promising solution. Memristor based synapses can be up to three times smaller than Complementary Metal Oxide Semiconductor (CMOS) based synapses.
In this thesis, the Programmable Metallization Cell (a memristive device) is used to prove a learning algorithm known as Spike Time Dependant Plasticity (STDP). This learning algorithm is an extension to Hebb’s learning rule in which the synapses weight can be altered by the relative timing of spikes across it. The synaptic weight with the memristor will be its conductance, and CMOS oscillator based circuits will be used to produce spikes that can modulate the memristor conductance by firing with different phases differences.
The human brain has always been a mystery to scientists. Modern day super computers are outperformed by the human brain in certain computations. The brain occupies far less space and consumes a fraction of the power a super computer does with certain processes such as pattern recognition. Neuromorphic computing aims to mimic biological neural systems on silicon to exploit the massive parallelism that neural systems offer. Neuromorphic systems are event driven systems rather than being clock driven. One of the issues faced by neuromorphic computing was the area occupied by these circuits. With recent developments in the field of nanotechnology, memristive devices on a nanoscale have been developed and show a promising solution. Memristor based synapses can be up to three times smaller than Complementary Metal Oxide Semiconductor (CMOS) based synapses.
In this thesis, the Programmable Metallization Cell (a memristive device) is used to prove a learning algorithm known as Spike Time Dependant Plasticity (STDP). This learning algorithm is an extension to Hebb’s learning rule in which the synapses weight can be altered by the relative timing of spikes across it. The synaptic weight with the memristor will be its conductance, and CMOS oscillator based circuits will be used to produce spikes that can modulate the memristor conductance by firing with different phases differences.
ContributorsSivaraj, Mahraj (Author) / Barnaby, Hugh James (Thesis advisor) / Kozicki, Michael (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2015
Description
Accessibility to the internal nodes of an analog/mixed-signal circuit while testing is extremely difficult. Furthermore, with technology scaling, the effect of process variations becomes more pronounced which in turn effects the test time, test cost, and die yield. As devices become more unreliable, the probability of failure of a die increases, yield decreases affecting the quality of test and cost.Therefore, test time minimization and test cost reduction are important. Moreover, process variations can affect the performance of analog/mixed circuits. Therefore, the performance of a System On-Chip(SoC) which tends to integrate multiple band gap reference circuits (BGRs) is effected due to the wide variations caused in the behavior of the BGR as a result of increasing process variations. Calibration of the BGR is, thus, important in the test process so as to obtain accuracy in the measurement of the output voltage of BGR. Furthermore, as test time minimization and test cost reduction are important in a test process, Built-in Self Test (BIST) techniques have become more popular. To obtain accuracy in the measurement of the output voltage of BGR, a VCO-based zoom-in ADC architecture that was designed to calibrate the output of the BGR voltage which dictates the circuit performance. However, the zoom-voltages for the circuit are generated using a tester. As the number of such ADCs integrated on a SoC increase, the number of nodes to be accessed by the tester increase. Moreover, the capacitance of the probe affects the accuracy of the applied input voltages of the VCO-based ADC. Therefore, accessibility decreases with increase in scaling.Further, generating a wide range of inputs becomes burdensome for the tester. For all the above reasons, an on-chip DAC circuitry was proposed as a part of this thesis, to decrease the reliance on tester. The suggested DAC architecture is a simple resistor string whose resolution depends on the number of zoom-in voltages to be generated. This architecture has a linear and monotonic behavior which is very important as the VCO has a highly non-linear behavior. Thus, the voltages generated by the DAC should be accurate with minimum error so that the worst-case Integral Non-Linearity error (INL) is less than 1mV considering resistor mismatches over process variations. With the increase in the number of VCO-based ADCs on a chip, the test time savings increase exponentially. Thus, the introduction of an on-chip DAC circuitry offers various advantages like decreasing accessibility requirement during the test process, occupying less area, reducing test cost and most importantly, decreasing the reliance on tester.
ContributorsRavouri, Yestina (Author) / Ozev, Sule (Thesis advisor) / Ogras, Umit Y. (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2017
Description
Micro Electro Mechanical Systems (MEMS) based accelerometers are one of the most commonly used sensors out there. They are used in devices such as, airbags, smartphones, airplanes, and many more. Although they are very accurate, they degrade with time or get offset due to some damage. To fix this, they must be calibrated again using physical calibration technique, which is an expensive process to conduct. However, these sensors can also be calibrated infield by applying an on-chip electrical stimulus to the sensor. Electrical stimulus-based calibration could bring the cost of testing and calibration significantly down as compared to factory testing. In this thesis, simulations are presented to formulate a statistical prediction model based on an electrical stimulus. Results from two different approaches of electrical calibration have been discussed. A prediction model with a root mean square error of 1% has been presented in this work. Experiments were conducted on commercially available accelerometers to test the techniques used for simulations.
ContributorsBassi, Ishaan (Author) / Ozev, Sule (Thesis advisor) / Christen, Jennifer Blain (Committee member) / Vasileska, Dragica (Committee member) / Arizona State University (Publisher)
Created2020