Matching Items (67)
Filtering by
- All Subjects: Electrical Engineering
- Creators: Kitchen, Jennifer
Description
Negative Bias Temperature Instability (NBTI) is commonly seen in p-channel transistors under negative gate voltages at an elevated temperature. The interface traps, oxide traps and NBTI mechanisms are discussed and their effect on circuit degradation and results are discussed. This thesis focuses on developing a model for simulating impact of NBTI effects at circuit level. The model mimics the effects of degradation caused by the defects.
The NBTI model developed in this work is validated and sanity checked by using the simulation data from silvaco and gives excellent results. Furthermore the susceptibility of CMOS circuits such as the CMOS inverter, and a ring oscillator to NBTI is investigated. The results show that the oscillation frequency of a ring oscillator decreases and the SET pulse broadens with the NBTI.
The NBTI model developed in this work is validated and sanity checked by using the simulation data from silvaco and gives excellent results. Furthermore the susceptibility of CMOS circuits such as the CMOS inverter, and a ring oscillator to NBTI is investigated. The results show that the oscillation frequency of a ring oscillator decreases and the SET pulse broadens with the NBTI.
ContributorsPadala, Sudheer (Author) / Barnaby, Hugh (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2014
Description
Power Management circuits are employed in almost all electronic equipment and they have energy storage elements (capacitors and inductors) as building blocks along with other active circuitry. Power management circuits employ feedback to achieve good load and line regulation. The feedback loop is designed at an operating point and component values are chosen to meet that design requirements. But the capacitors and inductors are subject to variations due to temperature, aging and load stress. Due to these variations, the feedback loop can cross its robustness margins and can lead to degraded performance and potential instability. Another issue in power management circuits is the measurement of their frequency response for stability assessment. The standard techniques used in production test environment require expensive measurement equipment (Network Analyzer) and time. These two issues of component variations and frequency response measurement can be addressed if the frequency response of the power converter is used as measure of component (capacitor and inductor) variations. So, a single solution of frequency response measurement solves both the issues. This work examines system identification (frequency response measurement) of power management circuits based on cross correlation technique and proposes the use of switched capacitor correlator for this purpose. A switched capacitor correlator has been designed and used in the system identification of Linear and Switching regulators. The obtained results are compared with the standard frequency response measurement methods of power converters.
ContributorsMalladi, Venkata Naga Koushik (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
ContributorsJavidahmadabadi, Mahdi (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Aberle, James T., 1961- (Committee member) / Arizona State University (Publisher)
Created2015
Description
RF transmitter manufacturers go to great extremes and expense to ensure that their product meets the RF output power requirements for which they are designed. Therefore, there is an urgent need for in-field monitoring of output power and gain to bring down the costs of RF transceiver testing and ensure product reliability. Built-in self-test (BIST) techniques can perform such monitoring without the requirement for expensive RF test equipment. In most BIST techniques, on-chip resources, such as peak detectors, power detectors, or envelope detectors are used along with frequency down conversion to analyze the output of the design under test (DUT). However, this conversion circuitry is subject to similar process, voltage, and temperature (PVT) variations as the DUT and affects the measurement accuracy. So, it is important to monitor BIST performance over time, voltage and temperature, such that accurate in-field measurements can be performed.
In this research, a multistep BIST solution using only baseband signals for test analysis is presented. An on-chip signal generation circuit, which is robust with respect to time, supply voltage, and temperature variations is used for self-calibration of the BIST system before the DUT measurement. Using mathematical modelling, an analytical expression for the output signal is derived first and then test signals are devised to extract the output power of the DUT. By utilizing a standard 180nm IBM7RF CMOS process, a 2.4GHz low power RF IC incorporated with the proposed BIST circuitry and on-chip test signal source is designed and fabricated. Experimental results are presented, which show this BIST method can monitor the DUT’s output power with +/- 0.35dB accuracy over a 20dB power dynamic range.
In this research, a multistep BIST solution using only baseband signals for test analysis is presented. An on-chip signal generation circuit, which is robust with respect to time, supply voltage, and temperature variations is used for self-calibration of the BIST system before the DUT measurement. Using mathematical modelling, an analytical expression for the output signal is derived first and then test signals are devised to extract the output power of the DUT. By utilizing a standard 180nm IBM7RF CMOS process, a 2.4GHz low power RF IC incorporated with the proposed BIST circuitry and on-chip test signal source is designed and fabricated. Experimental results are presented, which show this BIST method can monitor the DUT’s output power with +/- 0.35dB accuracy over a 20dB power dynamic range.
ContributorsGangula, Sudheer Kumar Reddy (Author) / Kitchen, Jennifer (Thesis advisor) / Ozev, Sule (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
Description
Due to high level of integration in RF System on Chip (SOC), the test access points are limited to the baseband and RF inputs/outputs of the system. This limited access poses a big challenge particularly for advanced RF architectures where calibration of internal parameters is necessary and ensure proper operation. Therefore low-overhead built-in Self-Test (BIST) solution for advanced RF transceiver is proposed. In this dissertation. Firstly, comprehensive BIST solution for RF polar transceivers using on-chip resources is presented. In the receiver, phase and gain mismatches degrade sensitivity and error vector magnitude (EVM). In the transmitter, delay skew between the envelope and phase signals and the finite envelope bandwidth can create intermodulation distortion (IMD) that leads to violation of spectral mask requirements. Characterization and calibration of these parameters with analytical model would reduce the test time and cost considerably. Hence, a technique to measure and calibrate impairments of the polar transceiver in the loop-back mode is proposed.
Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced.
Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method.
Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed.
Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.
Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced.
Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method.
Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed.
Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.
ContributorsJeong, Jae Woong (Author) / Ozev, Sule (Thesis advisor) / Kitchen, Jennifer (Committee member) / Cao, Yu (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
Description
The demand for the higher data rate in the wireless telecommunication is increasing rapidly. Providing higher data rate in cellular telecommunication systems is limited because of the limited physical resources such as telecommunication frequency channels. Besides, interference with the other users and self-interference signal in the receiver are the other challenges in increasing the bandwidth of the wireless telecommunication system.
Full duplex wireless communication transmits and receives at the same time and the same frequency which was assumed impossible in the conventional wireless communication systems. Full duplex wireless communication, compared to the conventional wireless communication, doubles the channel efficiency and bandwidth. In addition, full duplex wireless communication system simplifies the reusing of the radio resources in small cells to eliminate the backhaul problem and simplifies the management of the spectrum. Finally, the full duplex telecommunication system reduces the costs of future wireless communication systems.
The main challenge in the full duplex wireless is the self-interference signal at the receiver which is very large compared to the receiver noise floor and it degrades the receiver performance significantly. In this dissertation, different techniques for the antenna interface and self-interference cancellation are proposed for the wireless full duplex transceiver. These techniques are designed and implemented on CMOS technology. The measurement results show that the full duplex wireless is possible for the short range and cellular wireless communication systems.
Full duplex wireless communication transmits and receives at the same time and the same frequency which was assumed impossible in the conventional wireless communication systems. Full duplex wireless communication, compared to the conventional wireless communication, doubles the channel efficiency and bandwidth. In addition, full duplex wireless communication system simplifies the reusing of the radio resources in small cells to eliminate the backhaul problem and simplifies the management of the spectrum. Finally, the full duplex telecommunication system reduces the costs of future wireless communication systems.
The main challenge in the full duplex wireless is the self-interference signal at the receiver which is very large compared to the receiver noise floor and it degrades the receiver performance significantly. In this dissertation, different techniques for the antenna interface and self-interference cancellation are proposed for the wireless full duplex transceiver. These techniques are designed and implemented on CMOS technology. The measurement results show that the full duplex wireless is possible for the short range and cellular wireless communication systems.
ContributorsAyati, Seyyed Amir (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Bliss, Daniel (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017
Description
A 4-phase, quasi-current-mode hysteretic buck converter with digital frequency synchronization, online comparator offset-calibration and digital current sharing control is presented. The switching frequency of the hysteretic converter is digitally synchronized to the input clock reference with less than ±1.5% error in the switching frequency range of 3-9.5MHz. The online offset calibration cancels the input-referred offset of the hysteretic comparator and enables ±1.1% voltage regulation accuracy. Maximum current-sharing error of ±3.6% is achieved by a duty-cycle-calibrated delay line based PWM generator, without affecting the phase synchronization timing sequence. In light load conditions, individual converter phases can be disabled, and the final stage power converter output stage is segmented for high efficiency. The DC-DC converter achieves 93% peak efficiency for Vi = 2V and Vo = 1.6V.
ContributorsSun, Ming (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Seo, Jae-Sun (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017
Description
The growing demand for high performance and power hungry portable electronic devices has resulted in alarmingly serious thermal concerns in recent times. The power management system of such devices has thus become increasingly more vital. An integral component of this system is a Low-Dropout Regulator (LDO) which inherently generates a low-noise power supply. Such power supplies are crucial for noise sensitive analog blocks like analog-to-digital converters, phase locked loops, radio-frequency circuits, etc. At higher output power however, a single LDO suffers from increased heat dissipation leading to thermal issues.
This research presents a novel approach to equally and accurately share a large output load current across multiple parallel LDOs to spread the dissipated heat uniformly. The proposed techniques to achieve a high load sharing accuracy of 1% include an innovative fully-integrated accurate current sensing technique based on Dynamic Element Matching and an integrator based servo loop with a low offset feedback amplifier. A novel compensation scheme based on a switched capacitor resistor is referenced to address the high 2A output current specification per LDO across an output voltage range of 1V to 3V. The presented scheme also reduces stringent requirements on off-chip board traces and number of off-chip components thereby making it suitable for portable hand-held systems. The proposed approach can theoretically be extended to any number of parallel LDOs increasing the output current range extensively. The designed load sharing LDO features fast transient response for a low quiescent current consumption of 300µA with a power-supply rejection of 60.7dB at DC. The proposed load sharing technique is verified through extensive simulations for various sources and ranges of mismatch across process, voltage and temperature.
This research presents a novel approach to equally and accurately share a large output load current across multiple parallel LDOs to spread the dissipated heat uniformly. The proposed techniques to achieve a high load sharing accuracy of 1% include an innovative fully-integrated accurate current sensing technique based on Dynamic Element Matching and an integrator based servo loop with a low offset feedback amplifier. A novel compensation scheme based on a switched capacitor resistor is referenced to address the high 2A output current specification per LDO across an output voltage range of 1V to 3V. The presented scheme also reduces stringent requirements on off-chip board traces and number of off-chip components thereby making it suitable for portable hand-held systems. The proposed approach can theoretically be extended to any number of parallel LDOs increasing the output current range extensively. The designed load sharing LDO features fast transient response for a low quiescent current consumption of 300µA with a power-supply rejection of 60.7dB at DC. The proposed load sharing technique is verified through extensive simulations for various sources and ranges of mismatch across process, voltage and temperature.
ContributorsTalele, Bhushan (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Seo, Jae-Sun (Committee member) / Arizona State University (Publisher)
Created2017
Description
Performance failure due to aging is an increasing concern for RF circuits. While most aging studies are focused on the concept of mean-time-to-failure, for analog circuits, aging results in continuous degradation in performance before it causes catastrophic failures. In this regard, the lifetime of RF/analog circuits, which is defined as the point where at least one specification fails, is not just determined by aging at the device level, but also by the slack in the specifications, process variations, and the stress conditions on the devices. In this dissertation, firstly, a methodology for analyzing the performance degradation of RF circuits caused by aging mechanisms in MOSFET devices at design-time (pre-silicon) is presented. An algorithm to determine reliability hotspots in the circuit is proposed and design-time optimization methods to enhance the lifetime by making the most likely to fail circuit components more reliable is performed. RF circuits are used as test cases to demonstrate that the lifetime can be enhanced using the proposed design-time technique with low area and no performance impact. Secondly, in-field monitoring and recovering technique for the performance of aged RF circuits is discussed. The proposed in-field technique is based on two phases: During the design time, degradation profiles of the aged circuit are obtained through simulations. From these profiles, hotspot identification of aged RF circuits are conducted and the circuit variable that is easy to measure but highly correlated to the performance of the primary circuit is determined for a monitoring purpose. After deployment, an on-chip DC monitor is periodically activated and its results are used to monitor, and if necessary, recover the circuit performances degraded by aging mechanisms. It is also necessary to co-design the monitoring and recovery mechanism along with the primary circuit for minimal performance impact. A low noise amplifier (LNA) and LC-tank oscillators are fabricated for case studies to demonstrate that the lifetime can be enhanced using the proposed monitoring and recovery techniques in the field. Experimental results with fabricated LNA/oscillator chips show the performance degradation from the accelerated stress conditions and this loss can be recovered by the proposed mitigation scheme.
ContributorsChang, Doo Hwang (Author) / Ozev, Sule (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2017
Description
A modeling platform for predicting total ionizing dose (TID) and dose rate response of commercial commercial-off-the-shelf (COTS) linear bipolar circuits and technologies is introduced. Tasks associated with the modeling platform involve the development of model to predict the excess current response in a bipolar transistor given inputs of interface (NIT) and oxide defects (NOT) which are caused by ionizing radiation exposure. Existing models that attempt to predict this excess base current response are derived and discussed in detail. An improved model is proposed which modifies the existing model and incorporates the impact of charged interface trap defects on radiation-induced excess base current. The improved accuracy of the new model in predicting excess base current response in lateral PNP (LPNP) is then verified with Technology Computer Aided Design (TCAD) simulations. Finally, experimental data and compared with the improved and existing model calculations.
ContributorsTolleson, Blayne S. (Author) / Barnaby, Hugh J (Thesis advisor) / Gonzalez-Velo, Yago (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017