Matching Items (6)
Description
A hybrid PV/T module was built, consisting of a thermal liquid heating system and a photovoltaic module system that combine in a hybrid format. This report will discuss the work on the project from Fall 2012 to Spring 2013 and the extended section on the economics for the Honors Thesis. Three stages of experiments were completed. Stage 1 showed our project was functional as we were able to verify our panel produced electricity and increased the temperature of water flowing in the system by 0.65°C. Stage 2 testing included “gluing” the flow system to the back of the panel resulting in an average increase of 4.76°C in the temperature of the water in the system. Stage 3 testing included adding insulating foam to the module which resulted in increasing the average temperature of the water in our flow system by 6.95°C. The economic calculations show the expected energy cost savings for Arizona residents.
ContributorsHaines, Brent Robert (Author) / Roedel, Ronald (Thesis director) / Aberle, James (Committee member) / Rauch, Dawson (Committee member) / Barrett, The Honors College (Contributor) / Electrical Engineering Program (Contributor)
Created2013-05
Description
A high voltage plasma arc can be created and sustained in air by subjecting the gases to an electric field with high voltage potential, causing ionization. The internal energy of the ionized gases can be transferred to corresponding pressure waves when the matter involved switches between the gaseous and plasma states. By pulse-width modulating a transformer driving signal, the transfer of internal electrical energy to resonating pressure waves may be controlled. Audio wave input to the driver signal can then be modulated into the carrier wave and be used to determine the width of each pulse in the plasma, thus reconstructing the audio signal as pressure, or sound waves, as the plasma arc switches on and off. The result will be the audio waveform resonating out of the plasma arc as audible sound, and thus creating a plasma loudspeaker. Theory of operation was tested through construction of a plasma arc speaker, and resultant audio playback was analyzed. This analysis confirmed accurate reproduction of audio signal in audible sound.
ContributorsBoehringer, Brian Thomas (Author) / Roedel, Ronald (Thesis director) / Huffman, James (Committee member) / Barrett, The Honors College (Contributor) / Electrical Engineering Program (Contributor)
Created2014-05
Description
The main objective of this project was to continue research and development of a building integrated solar thermoelectric generator (BISTEG). BISTEG is a promising renewable energy technology that is capable of generating electrical energy from the heat of concentrated sunlight. In order to perform R&D, the performance of different TEG cells and TEG setups were tested and analyzed, proof-of-concepts and prototypes were built. and the performance of the proof-of-concepts and prototypes were tested and analyzed as well. In order to test different TEG cells and TEG setups, a TEG testing apparatus was designed and fabricated. The apparatus is capable of comparing the performance of TEGs with temperature differentials up to 200 degrees C. Along with a TEG testing apparatus, several proof-of-concepts and prototypes were completed. All of these were tested in order to determine the feasibility of the design. All three proof-of-concepts were only capable of producing a voltage output less than 300mV. The prototype, however, was capable of producing a max output voltage of 17 volts. Although the prototype outperformed all of the proof-of-concepts, optimizations to the design can continue to improve the output voltage. In order to do so, stacked TEG tests were performed. After performing the stacked TEG tests, it was determined that the use of stacked TEGs depended on the Fresnel lens chosen. If BISTEG were to use a point focused Fresnel lens, using a stack of TEGs could increase the power density. If BISTEG were to utilize a linear focused Fresnel lens, however, the TEGs should not be stacked. It would be more efficient to lay them out side by side. They can be stacked, however, if the energy density needs to be increased and the costs of the additional TEGs are not an issue.
ContributorsPark, Andrew (Author) / Seager, Thomas (Thesis director) / Margaret, Hinrichs (Committee member) / Mechanical and Aerospace Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
The purpose of this research is to study the effect of angle of acceptance and mechanical control system noise on the power available to a two-axis solar concentrating photovoltaic (CPV) system. The efficiency of a solar CPV system is greatly dependent on the accuracy of the tracking system because a strong focal point is needed to concentrate incident solar irradiation on the small, high efficiency cells. The objective of this study was to evaluate and quantify tracking accuracy for a performance model which would apply to similar two-axis systems. An analysis comparing CPV to traditional solar photovoltaics from an economic standpoint was conducted as well to evaluate the viability of emerging CPV technology. The research was performed using two calibrated solar radiation sensors mounted on the plane of the tracking system, normal to the sun. One sensor is held at a constant, normal angle (0 degrees) and the other is varied by a known interior angle in the range of 0 degrees to 10 degrees. This was to study the magnitude of the decrease in in irradiance as the angle deviation increases. The results show that, as the interior angle increases, the solar irradiance and thus available power available on the focal point will decrease roughly at a parabolic rate, with a sharp cutoff point at angles greater than 5 degrees. These findings have a significant impact on CPV system tracking mechanisms, which require high precision tracking in order to perform as intended.
ContributorsPodzemny, Dominic James (Author) / Reddy, Agami (Thesis director) / Kelman, Jonathan (Committee member) / Mechanical and Aerospace Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
Description
The project described here is a solar powered intrusion detection system consisting of three modules: a battery recharging circuit, a laser emitter and photodetector pair, and a Wi- Fi connectivity board. Over the preceding seven months, great care has been taken for the design and construction of this system. The first three months were spent researching and selecting suitable IC's and external components (e.g. solar panel, batteries, etc.). Then, the next couple of months were spent ordering specific materials and equipment for the construction of our prototype. Finally, the last two months were used to build a working prototype, with a substantial amount of time used for perfecting our system's packaging and operation. This report will consist of a detailed discussion of our team's research, design activities, prototype implementation, final budget, and final schedule. Technical discussion of the concepts behind our design will assist with understanding the design activities and prototype implementation sections that will follow. Due to the generous funding of the group from the Barrett Honors College, our overall budget available for the project was $1600. Of that amount, only $334.51 was spent on the actual system components, with $829.42 being spent on the equipment and materials needed for the testing and construction of the prototype. As far as the schedule goes, we are essentially done with the project. The only tasks left to finish are a successful defense of the project at the oral presentation on Friday, 29 March 2013, followed by a successful demo on 26 April 2013.
ContributorsTroyer, Nicole L. (Co-author) / Shtayer, Idan (Co-author) / Guise, Chris (Co-author) / Kozicki, Michael (Thesis director) / Roedel, Ronald (Committee member) / Goodnick, Stephen (Committee member) / Barrett, The Honors College (Contributor) / Electrical Engineering Program (Contributor)
Created2013-05
Description
As the need for environmentally friendly and renewable fuel sources rises, many are considering alternative fuel sources, such as solar power. The device explored in this report uses solar power, in theory, to heat a metal oxide, cerium oxide, to a desired temperature. At specific temperatures and pressures, a reaction between an input gas, carbon dioxide or water vapor, and the metal oxide may produce fuel in the form of hydrogen or carbon monoxide. In order to reach the temperatures required by the reaction, a filament inside a high-temperature radiant heater must be heated to the desired temperature. In addition, the system’s pressure range must be satisfied. A pressure and temperature measurement device, as well as a voltage control, must be connected to an interface with a computer in order to monitor the pressure and temperature of different parts of the system. The cerium oxide element must also be constructed and placed inside the system. The desired shape of the cerium oxide material is a tube, to allow the flow of gas through the tubes and system and to provide mechanical strength. To construct the metal oxide tubes, they need to be extruded, dried, and sintered correctly. All the manufactured elements described serve an essential purpose in the system and are discussed further in this document.
This report focuses on the manufacturing of ceria tubes, the construction of a high-temperature radiant heater filament, and the implementation of a pressure measurement device. The manufacturing of ceria tubes includes the extrusion, the drying, and the sintering of the tubes. In addition, heating element filament construction consists of spot-welding certain metals together to create a device similar to that of a light bulb filament. Different methods were considered in each of these areas, and they are described in this report. All of the explorations in this document move towards the final device, a thermochemical reactor for the production of hydrogen (H2) and carbon monoxide (CO) from water (H2O) and carbon dioxide (CO2).
The results of this report indicate that there are several important manufacturing steps to create the most desirable results, in terms of tube manufacturing and heating element design. For the correct tube construction, they must be dried in a drying rack, and they must be sintered in V-groove plates. In addition, the results of the heating element manufacturing indicate that the ideal heating element filament needs to be simple in design (easily fixed), cost-effective, require little construction time, attach to the ends of the system easily, provide mechanical flexibility, and prevent the coil from touching the walls of the tube it lies in. Each aspect of the ideal elements, whether they are tubes or heating elements, is explored in this report.
This report focuses on the manufacturing of ceria tubes, the construction of a high-temperature radiant heater filament, and the implementation of a pressure measurement device. The manufacturing of ceria tubes includes the extrusion, the drying, and the sintering of the tubes. In addition, heating element filament construction consists of spot-welding certain metals together to create a device similar to that of a light bulb filament. Different methods were considered in each of these areas, and they are described in this report. All of the explorations in this document move towards the final device, a thermochemical reactor for the production of hydrogen (H2) and carbon monoxide (CO) from water (H2O) and carbon dioxide (CO2).
The results of this report indicate that there are several important manufacturing steps to create the most desirable results, in terms of tube manufacturing and heating element design. For the correct tube construction, they must be dried in a drying rack, and they must be sintered in V-groove plates. In addition, the results of the heating element manufacturing indicate that the ideal heating element filament needs to be simple in design (easily fixed), cost-effective, require little construction time, attach to the ends of the system easily, provide mechanical flexibility, and prevent the coil from touching the walls of the tube it lies in. Each aspect of the ideal elements, whether they are tubes or heating elements, is explored in this report.
ContributorsCaron, Danielle (Author) / Milcarek, Ryan (Thesis director) / Ermanoski, Ivan (Committee member) / Stechel, Ellen (Committee member) / Mechanical and Aerospace Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2020-05