Matching Items (25)
Filtering by
- All Subjects: chemical engineering
- Creators: Emady, Heather
- Member of: ASU Electronic Theses and Dissertations
- Resource Type: Text
Description
The purpose of this study was to comprehend the global warming potential (GWP), cost variability, and competitiveness of steel with rising carbon taxes. Aluminum, glass fiber composite, and carbon fiber composite were chosen as competing materials. In order to compare the aforementioned factors, the GWP of several processes to produce steel, aluminum, and fiber composites was examined. Cost analyses of various methods were also carried out to determine their viability. Energy consumption data for each of the paths under consideration were taken from the literature for the study. To get the consistent GWP for traditional and decarbonized scenarios, the required energy is multiplied with corresponding energy source (natural gas or electricity). Even after accounting for the carbon tax and the weight-reduction factor, the results show that steel still has the lowest production costs, followed by aluminum, while fiber composites remain the most costly. EAF- steel and secondary aluminum has least GWP followed by H2-DRI (Hydrogen- Direct Reduced Iron)steel and NG-DRI (Natural Gas- Direct Reduced Iron) steel with carbon capture and storage (CCS). The state of art technology for glass fiber reinforced composite also emits less carbon dioxide but the cost of production is still high. Carbon fiber reinforced composite emits most carbon dioxide and is least economical.
ContributorsRajulwar, Vaishnavi Vijay (Author) / Seetharaman, Sridhar (Thesis advisor) / Emady, Heather (Committee member) / Nian, Qiong (Committee member) / Arizona State University (Publisher)
Created2023
Description
This work describes the development of a device for measuring CO2 in breath, which has applications in monitoring a variety of health issues, such as Chronic Obstructive Pulmonary Disease (COPD), asthma, and cardiovascular disease. The device takes advantage of colorimetric sensing technology in order to maintain a low cost and high user-friendliness. The sensor consists of a pH dye, reactive element, and base coated on a highly porous Teflon membrane. The transmittance of the sensor is measured in the device via a simple LED/photodiode system, along with the flow rate, ambient relative humidity, and barometric pressure. The flow is measured by a newly developed flow meter described in this work, the Confined Pitot Tube (CPT) flow meter, which provides a high accuracy with reduced flow-resistance with a standard differential pressure transducer. I demonstrate in this work that the system has a high sensitivity, high specificity, fast time-response, high reproducibility, and good stability. The sensor has a simple calibration method which requires no action by the user, and utilizes a sophisticated, yet lightweight, model in order to predict temperature changes on the sensor during breathing and track changes in water content. It is shown to be effective for measuring CO2 waveform parameters on a breath-by-breath basis, such as End-Tidal CO2, Alveolar Plateau Slope, and Beginning Exhalation Slope.
ContributorsBridgeman, Devon (Author) / Forzani, Erica S (Thesis advisor) / Nikkhah, Mehdi (Committee member) / Holloway, Julianne (Committee member) / Raupp, Gregory (Committee member) / Emady, Heather (Committee member) / Arizona State University (Publisher)
Created2017
Description
This study presents an evaluation of the predicted flow behavior and the minimum outlet diameter in a computationally simulated hopper. The flow pattern in hoppers was simulated to test three size fractions, three moisture levels of microcrystalline cellulose (MCC), and two hopper wall angles in Multiphase Flow with Interphase eXchanges (MFiX). Predictions from MFiX were then compared to current literature. As expected, the smaller size fractions with lower water content were closer to ideal funnel flow than their larger counterparts. The predicted minimum outlet diameter in simulations showed good agreement with close to ideal flowability. These findings illustrate the connection between lab flowability experiments and computational simulations. Lastly, three fluidized bed simulations were also created in MFiX with zeolite 13X to analyze the pressure and velocity within the bed. The application of flowability simulations can improve the transport of solids in processing equipment used during the production of powders.
ContributorsBuchanan, Lidija (Author) / Emady, Heather (Thesis advisor) / Muhich, Christopher (Committee member) / Deng, Shuguang (Committee member) / Arizona State University (Publisher)
Created2023
Description
Anthropogenic processes have increased the concentration of toxic Se, As and N in water. Oxo-anions of these species are poisonous to aquatic and terrestrial life. Current remediation techniques have low selectivity towards their removal. Understanding the chemistry and physics which control oxo-anion adsorption on metal oxide and the catalytic nitrate reduction to inform improved remediation technologies can be done using Density functional theory (DFT) calculations. The adsorption of selenate, selenite, and arsenate was investigated on the alumina and hematite to inform sorbent design strategies. Adsorption energies were calculated as a function of surface structure, composition, binding motif, and pH within a hybrid implicit-explicit solvation strategy. Correlations between surface property descriptors including water network structure, cationic species identity, and facet and the adsorption energies of the ions show that the surface water network controls the adsorption energy more than any other, including the cationic species of the metal-oxide. Additionally, to achieve selectivity for selenate over sulphate, differences in their electronic structure must be exploited, for example by the reduction of selenate to selenite by Ti3+ cations.
Thermochemical or electrochemical reduction pathways to convert NO3- to N2 or NH3, which are benign or value-added products, respectively are examined over single-atom electrocatalysts (SAC) in Cu. The activity and selectivity for nitrate reduction are compared with the competitive hydrogen evolution reaction (HER). Cu suppresses HER but produces toxic NO2- because of a high activation barrier for cleaving the second N-O bond. SACs provide secondary sites for reaction and break traditional linear scaling relationships. Ru-SACs selectively produce NH3 because N-O bond scission is facile, and the resulting N remains isolated on SAC sites; reacting with H+ from solvating H2O to form ammonia. Conversely, Pd-SAC forms N2 because the reduced N* atoms migrate to the Cu surface, which has a low H availability, allowing N atoms to combine to N2. This relation between N* binding preference and reduction product is demonstrated across an array of SAC elements.
Hence, the solvation effects on the surface critically alter the activity of adsorption and catalysis and the removal of toxic pollutants can be improved by altering the surface water network.
ContributorsGupta, Srishti (Author) / Muhich, Christopher L (Thesis advisor) / Singh, Arunima (Committee member) / Emady, Heather (Committee member) / Westerhoff, Paul (Committee member) / Deng, Shuguang (Committee member) / Arizona State University (Publisher)
Created2023
Description
Adsorption is fundamentally known to be a non-isothermal process; in which temperature increase is largely significant, causing fairly appreciable impacts on the processkinetics. For porous adsorbent particles like metal organic frameworks (MOFs), silica
gel, and zeolite, the resultant relative heat generated is partly distributed within the
particle, and the rest is transferred to the surrounding ambient fluid (air).
For large step changes in adsorbed phase concentration and fast adsorption rates,
especially, the isothermality of adsorption (as in some studies) is an inadequate assumption and inspires rather erroneous diffusivities of porous adsorbents. Isothermal models, in consequence, are insufficient for studying adsorption in porous adsorbents. Non-isothermal models can satisfactorily and exhaustively describe adsorption
in porous adsorbents. However, in many of the analyses done using the models, the
thermal conductivity of the adsorbent is assumed to be infinite; thus, particle temperature is taken to be fairly uniform during the process—a trend not observed for
carbon dioxide (CO2) adsorption on MOFs.
A new and detailed analysis of CO2 adsorption in a single microporous MOF-5
particle, assuming a finite effective thermal conductivity along with comprehensive
parametric studies for the models, is presented herein. A significant average temperature increase of 5K was calculated using the new model, compared to the 0.7K
obtained using the Stremming model. A corresponding increase in diffusivity from
8.17 x 10-13 to 1.72 x 10-11 m2/s was observed, indicating the limitations of both
isothermal models and models that assume constant diffusivity.
ContributorsNkuutu, John (Author) / Lin, Jerry (Thesis advisor) / Emady, Heather (Committee member) / Deng, Shuguang (Committee member) / Arizona State University (Publisher)
Created2023
Description
Due to the use of fertilizers, concentrations of harmful nitrate have increased in groundwater and surface waters globally in the last century. Water treatment plants primarily use separation techniques for nitrate treatment, but these technologies create a high nitrate concentration brine that is costly to dispose of. This dissertation focuses on catalytic hydrogenation, an emerging technology capable of reducing nitrate to nitrogen gas using hydrogen gas (H2). This technology reduces nitrate at rates >95% and is an improvement over technologies used at water treatment plants, because the nitrate is chemically transformed with harmless byproducts and no nitrate brine. The goal of this dissertation is to upgrade the maturity of catalytic nitrate hydrogenation systems by overcoming several barriers hindering the scale-up of this technology. Objective 1 is to compare different methods of attaching the bimetallic catalyst to a hollow-fiber membrane surface to find a method that results in 1) minimized catalyst loss, and 2) repeatable nitrate removal over several cycles. Results showed that the In-Situ MCfR-H2 deposition was successful in reducing nitrate at a rate of 1.1 min-1gPd-1 and lost less than 0.05% of attached Pd and In cumulatively over three nitrate treatment cycles. Objective 2 is to synthesize catalyst-films with varied In3+ precursor decorated over a Pd0 surface to show the technology can 1) reliably synthesize In-Pd catalyst-films with varied bimetallic ratios, and 2) optimize nitrate removal activity by varying In-Pd ratio. Results showed that nitrate removal activity was optimized with a rate constant of 0.190 mg*min-1L-1 using a catalyst-film with a 0.045 In-Pd ratio. Objective 3 is to perform nitrate reduction in a continuous flow reactor for two months to determine if nitrate removal activity can be sustained over extended operation and identify methods to overcome catalyst deactivation. Results showed that a combination of increased hydraulic residence time and reduced pH was successful in increasing the nitrate removal and decreasing harmful nitrite byproduct selectivity to 0%. These objectives increased the technology readiness of this technology by enabling the reuse of the catalyst, maximizing nitrate reduction activity, and achieving long-term nitrate removal.
ContributorsLevi, Juliana (Author) / Westerhoff, Paul (Thesis advisor) / Rittmann, Bruce (Thesis advisor) / Garcia-Segura, Sergi (Committee member) / Wong, Michael (Committee member) / Lind Thomas, Mary Laura (Committee member) / Emady, Heather (Committee member) / Arizona State University (Publisher)
Created2023
Description
Membrane based technology is one of the principal methods currently in widespread use to address the global water shortage. Pervaporation desalination is a membrane technology for water purification currently under investigation as a method for processing reverse osmosis concentrates or for stand-alone applications. Concentration polarization is a potential problem in any membrane separation. In desalination concentration polarization can lead to reduced water flux, increased propensity for membrane scaling, and decreased quality of the product water. Quantifying concentration polarization is important because reducing concentration polarization requires increased capital and operating costs in the form of feed spacers and high feed flow velocities. The prevalent methods for quantifying concentration polarization are based on the steady state thin film boundary layer theory. Baker’s method, previously used for pervaporation volatile organic compound separations but not desalination, was successfully applied to data from five previously published pervaporation desalination studies. Further investigation suggests that Baker’s method may not have wide applicability in desalination. Instead, the limitations of the steady state assumption were exposed. Additionally, preliminary results of nanophotonic enhancement of pervaporation membranes were found to produce significant flux enhancement. A novel theory on the mitigation of concentration polarization by the photothermal effect was discussed.
ContributorsMann, Stewart, Ph.D (Author) / Lind, Mary Laura (Thesis advisor) / Walker, Shane (Committee member) / Green, Matthew (Committee member) / Forzani, Erica (Committee member) / Emady, Heather (Committee member) / Arizona State University (Publisher)
Created2019
Description
This thesis investigated the effects of differing diameters and varying moisture content on the flowability properties of granular glass beads through use of a Freeman FT4 Powder Rheometer. These parameters were tested in order to construct an empirical model to predict flowability properties of glass beads at differing size ranges and moisture contents. The final empirical model outputted an average error of 8.73% across all tested diameters and moisture ranges.
Mohr's circles were constructed from experimentally-obtained shear stress values to quantitatively describe flowability of tested materials in terms of a flow function parameter. A high flow function value (>10) was indicative of a good flow.
By testing 120-180 µm, 120-350 µm, 180-250 µm, 250-350 µm, 430-600 µm, and 600-850 µm glass bead diameter ranges, an increase in size was seen to result in higher flow function values. The limitations of testing using the FT4 became apparent as inconsistent flow function values were obtained at 0% moisture with size ranges above 120-180 µm, or at flow function values of >21. Bead sizes larger than 430 µm showed significant standard deviation over all tested trials--when excluding size ranges above that value, the empirical model showed an average error of only 6.45%.
Wet material testing occurred at all tested glass bead size ranges using a deionized water content of 0%, 1%, 5%, 15%, and 20% by weight. The results of such testing showed a decrease in the resulting flow function parameter as more water content was added. However, this trend changed as 20% moisture content was achieved; the wet material became supersaturated, and an increase in flow function values was observed. The empirical model constructed, therefore, neglected the 20% moisture content regime.
Mohr's circles were constructed from experimentally-obtained shear stress values to quantitatively describe flowability of tested materials in terms of a flow function parameter. A high flow function value (>10) was indicative of a good flow.
By testing 120-180 µm, 120-350 µm, 180-250 µm, 250-350 µm, 430-600 µm, and 600-850 µm glass bead diameter ranges, an increase in size was seen to result in higher flow function values. The limitations of testing using the FT4 became apparent as inconsistent flow function values were obtained at 0% moisture with size ranges above 120-180 µm, or at flow function values of >21. Bead sizes larger than 430 µm showed significant standard deviation over all tested trials--when excluding size ranges above that value, the empirical model showed an average error of only 6.45%.
Wet material testing occurred at all tested glass bead size ranges using a deionized water content of 0%, 1%, 5%, 15%, and 20% by weight. The results of such testing showed a decrease in the resulting flow function parameter as more water content was added. However, this trend changed as 20% moisture content was achieved; the wet material became supersaturated, and an increase in flow function values was observed. The empirical model constructed, therefore, neglected the 20% moisture content regime.
ContributorsKleppe, Cameron (Author) / Emady, Heather (Thesis advisor) / Marvi, Hamidreza (Committee member) / Deng, Shuguang (Committee member) / Arizona State University (Publisher)
Created2019
Description
The current research is based on the principles of three-dimensional discrete element method (3D – DEM) through simulations, by using heat transfer models in EDEM, to investigate the effects of fill level, rotation rate and particle size on the steady-state conduction heat transfer in rotary drums. The high heat and mass transfer rates obtained through rotary drums make them very useful for powder mixing and heating processes in metallurgical, cement, mining, pharmaceutical, detergent and other particulate processing applications. However, these complex processes are difficult to model and operate since the particles can have a wide range of properties, and there is currently no way to predict the optimal operating conditions for a given material.
Steady-state heat transfer by conduction forms the basis for understanding other steady-state and unsteady-state heat transfer in a rotary drum – conduction, convection and radiation. Statistical analysis is carried out to determine the effects of these process parameters and find optimal operating conditions, which will thereby improve the heat transfer efficiency in rotary drums. A stainless-steel drum with a diameter of 6 inches and a length of 3 inches was modeled in EDEM with silica beads of sizes 2 mm, 3 mm and 4 mm at fill levels of 10%, 17.5% and 25%, and at rotation rates of 2 rpm, 5 rpm and 10 rpm. It was found that the heating uniformity increased with decreasing particle size, decreasing fill level and increasing rotation rate. This research is the first step towards studying the other heat transfer modes and various other process parameters. Better understanding of the various heat transfer modes, when used in combination for heating the particles, will be beneficial in improving the operating efficiency, reducing material costs and leading to significant energy conservation on a global scale.
Steady-state heat transfer by conduction forms the basis for understanding other steady-state and unsteady-state heat transfer in a rotary drum – conduction, convection and radiation. Statistical analysis is carried out to determine the effects of these process parameters and find optimal operating conditions, which will thereby improve the heat transfer efficiency in rotary drums. A stainless-steel drum with a diameter of 6 inches and a length of 3 inches was modeled in EDEM with silica beads of sizes 2 mm, 3 mm and 4 mm at fill levels of 10%, 17.5% and 25%, and at rotation rates of 2 rpm, 5 rpm and 10 rpm. It was found that the heating uniformity increased with decreasing particle size, decreasing fill level and increasing rotation rate. This research is the first step towards studying the other heat transfer modes and various other process parameters. Better understanding of the various heat transfer modes, when used in combination for heating the particles, will be beneficial in improving the operating efficiency, reducing material costs and leading to significant energy conservation on a global scale.
ContributorsBheda, Bhaumik (Author) / Emady, Heather (Thesis advisor) / Muhich, Christopher (Committee member) / Nielsen, David (Committee member) / Arizona State University (Publisher)
Created2020
Description
As experiencing hot months and thermal stresses is becoming more common, chemically protective fabrics must adapt and provide protections while reducing the heat stress to the body. These concerns affect first responders, warfighters, and workers regularly surrounded by hazardous chemical agents. While adapting traditional garments with cooling devices provides one route to mitigate this issue, these cooling methods add bulk, are time limited, and may not be applicable in locations without logistical support. Here I take inspiration from nature to guide the development of smart fabrics that have high breathability, but self-seal on exposure to target chemical(s), providing a better balance between cooling and protection.
Natural barrier materials were explored as a guide, focusing specifically on prickly pear cacti. These cacti have a natural waxy barrier that provides protection from dehydration and physically changes shape to modify surface wettability and water vapor transport. The results of this study provided a basis for a shape changing polymer to be used to respond directly to hazardous chemicals, swelling to contain the agent.
To create a stimuli responsive material, a novel superabsorbent polymer was synthesized, based on acrylamide chemistry. The polymer was tested for swelling properties in a wide range of organic liquids and found to highly swell in moderately polar organic liquids. To help predict swelling in untested liquids, the swelling of multiple test liquids were compared with their thermodynamic properties to observe trends. As the smart fabric needs to remain breathable to allow evaporative cooling, while retaining functionality when soaked with sweat, absorption of water, as well as that of an absorbing liquid in the presence of water were tested.
Micron sized particles of the developed polymer were deposited on a plastic mesh with pore size and open area similar to common clothing fabric to establish the proof of concept of using a breathable barrier to provide chemical protection. The polymer coated mesh showed minimal additional resistance to water vapor transport, relative to the mesh alone, but blocked more than 99% of a xylene aerosol from penetrating the barrier.
Natural barrier materials were explored as a guide, focusing specifically on prickly pear cacti. These cacti have a natural waxy barrier that provides protection from dehydration and physically changes shape to modify surface wettability and water vapor transport. The results of this study provided a basis for a shape changing polymer to be used to respond directly to hazardous chemicals, swelling to contain the agent.
To create a stimuli responsive material, a novel superabsorbent polymer was synthesized, based on acrylamide chemistry. The polymer was tested for swelling properties in a wide range of organic liquids and found to highly swell in moderately polar organic liquids. To help predict swelling in untested liquids, the swelling of multiple test liquids were compared with their thermodynamic properties to observe trends. As the smart fabric needs to remain breathable to allow evaporative cooling, while retaining functionality when soaked with sweat, absorption of water, as well as that of an absorbing liquid in the presence of water were tested.
Micron sized particles of the developed polymer were deposited on a plastic mesh with pore size and open area similar to common clothing fabric to establish the proof of concept of using a breathable barrier to provide chemical protection. The polymer coated mesh showed minimal additional resistance to water vapor transport, relative to the mesh alone, but blocked more than 99% of a xylene aerosol from penetrating the barrier.
ContributorsManning, Kenneth (Author) / Rykaczewski, Konrad (Thesis advisor) / Burgin, Timothy (Committee member) / Emady, Heather (Committee member) / Green, Matthew (Committee member) / Thomas, Marylaura (Committee member) / Arizona State University (Publisher)
Created2020