Matching Items (3)
Filtering by

Clear all filters

157332-Thumbnail Image.png

Combined UV-temperature-humidity accelerated testing of PV modules: reliability of UV-cut and UV-pass EVA encapsulants

Description
In the past, the photovoltaic (PV) modules were typically constructed with glass superstrate containing cerium oxide and EVA (ethylene vinyl acetate) encapsulant containing UV absorbing additives. However, in the current industry, the PV modules are generally constructed without cerium oxide in the glass and UV absorbing additives in EVA to…

In the past, the photovoltaic (PV) modules were typically constructed with glass superstrate containing cerium oxide and EVA (ethylene vinyl acetate) encapsulant containing UV absorbing additives. However, in the current industry, the PV modules are generally constructed without cerium oxide in the glass and UV absorbing additives in EVA to increase quantum efficiency of crystalline silicon solar cells in the UV regions. This new approach is expected to boost the initial power output of the modules and reduce the long-term encapsulant browning issues. However, this new approach could lead to other durability and reliability issues such as delamination of encapsulant by damaging interfacial bonds, destruction of antireflection coating on solar cells and even breakage of polymeric backbone of EVA. This work compares the durability and reliability issues of PV modules having glass without cerium oxide and EVA with (aka, UVcut or UVC) and without (aka, UVpass or UVP) UV absorbing additives. In addition, modules with UVP front and UVC back EVA have also been investigated (aka, UVhybrid or UVH). The mini-modules with nine split cells used in this work were fabricated at ASU’s Photovoltaic Reliability Laboratory. The durability and reliability caused by three stress variables have been investigated and the three variables are temperature, humidity/oxygen and UV dosage. The influence of up to 800 kWh/m2 UV dosage has been investigated at various dosage levels. Many material and device characterizations have been performed to ascertain the degradation modes and effects. The UVC modules showed encapsulant discoloration at the cell centers as expected but the UVH modules showed a ring-shaped encapsulant discoloration close to the cell edges as evidenced in the UV fluorescence (UVF) imaging study. The PV modules containing UVP on both sides of cells with limited access to humidity or oxygen through backsheet (covered backsheet with adhesive aluminum tape) seem to experience encapsulant delamination as evidenced in the UVF images. Plausible explanations for these observations have been presented.
ContributorsArularasu, Pooja (Author) / Tamizhmani, Govindasamy (Thesis advisor) / Mu, Bin (Thesis advisor) / Varman, Arul M (Committee member) / Arizona State University (Publisher)
Created2019

A study of heating and degradation of acrylonitrile-butadiene-styrene/polycarbonate polymer due to ultraviolet lasers illumination during localized pre-deposition heating for fused filament fabrication 3D printing

Description
With the growing popularity of 3d printing in recreational, research, and commercial enterprises new techniques and processes are being developed to improve the quality of parts created. Even so, the anisotropic properties is still a major hindrance of parts manufactured in this method. The goal is to produce parts that…

With the growing popularity of 3d printing in recreational, research, and commercial enterprises new techniques and processes are being developed to improve the quality of parts created. Even so, the anisotropic properties is still a major hindrance of parts manufactured in this method. The goal is to produce parts that mimic the strength characteristics of a comparable part of the same design and materials created using injection molding. In achieving this goal the production cost can be reduced by eliminating the initial investment needed for the creation of expensive tooling. This initial investment reduction will allow for a wider variant of products in smaller batch runs to be made available. This thesis implements the use of ultraviolet (UV) illumination for an in-process laser local pre-deposition heating (LLPH). By comparing samples with and without the LLPH process it is determined that applied energy that is absorbed by the polymer is converted to an increase in the interlayer temperature, and resulting in an observed increase in tensile strength over the baseline test samples. The increase in interlayer bonding thus can be considered the dominating factor over polymer degradation.
ContributorsKusel, Scott Daniel (Author) / Hsu, Keng (Thesis advisor) / Sodemann, Angela (Committee member) / Kannan, Arunachala M (Committee member) / Arizona State University (Publisher)
Created2017
168678-Thumbnail Image.png

Three Essays on Implementing a Sustainable Circular Economy for Plastics

Description
Plastic is a valuable part of the consumer economy, but it creates negative environmental externalities throughout its lifecycle. To reduce these effects, a sustainable circular economy is needed, where more plastic is diverted from landfill or environmental sinks through reduction, reuse, recycling, or composting, while addressing social needs. Although many…

Plastic is a valuable part of the consumer economy, but it creates negative environmental externalities throughout its lifecycle. To reduce these effects, a sustainable circular economy is needed, where more plastic is diverted from landfill or environmental sinks through reduction, reuse, recycling, or composting, while addressing social needs. Although many different stakeholders (industry, academia, policymakers) are calling for a sustainable circular economy for plastics, globally, less than 20% of plastic is recycled with no data on reduction and reuse. In this dissertation, a mixed methods approach is used to suggest how organizations related to the plastic industry can implement a sustainable circular economy. The first chapter identifies how firms across the plastic value chain can innovate to adopt a sustainable circular flow. A systematic review reveals over 300 examples, which are used to create a material flow typology. Findings summarize five critical points of innovation and indicate that innovation adoption is low. More concerted efforts are needed to improve innovation adoption and there is a need to shift innovation focus from resource efficiency to sustainability. The second chapters studies U.S. plastic recyclers’ price signals to generate evidence for favorable recycling policies. A hedonic analysis reveals recyclers preferences for recyclability – plastic properties that enable recycling. Results suggest that adequate recycling infrastructure and absence of virgin plastic can play an important role in facilitating more recycling. In the third paper, the role of governments as consumers is studied. As the largest consumers in a market, governments can signal a large demand for circular products and services, however public administration literature has paid limited attention to it. A theoretical framework is created to fill the knowledge gap and suggest how governments can use sustainable public procurement for a circular economy. A systematic literature review of the top ten public administration journals over 32 years reveals critical knowledge gaps and the potential for important sustainable public procurement research
ContributorsHafsa, Fatima (Author) / Englin, Jeffrey (Thesis advisor) / Abbott, Joshua K (Committee member) / Darnall, Nicole (Committee member) / Dooley, Kevin J (Committee member) / Arizona State University (Publisher)
Created2022