Novel hydride chemistries are employed to deposit light-emitting Ge_1-y Sn_yalloys with y ≤ 0.1 by Ultra-High Vacuum Chemical Vapor Deposition (UHV-CVD) on Ge-buffered Si wafers. The properties of the resultant materials are systematically compared with similar alloys grown directly on Si wafers. The fundamental difference between the two systems is a fivefold (and higher) decrease in lattice mismatch between film and virtual substrate, allowing direct integration of bulk-like crystals with planar surfaces and relatively low dislocation densities. For y ≤ 0.06, the CVD precursors used were digermane Ge₂H₆ and deuterated stannane SnD₄. For y ≥ 0.06, the Ge precursor was changed to trigermane Ge₃H₈, whose higher reactivity enabled the fabrication of supersaturated samples with the target film parameters. In all cases, the Ge wafers were produced using tetragermane Ge₄H₁₀ as the Ge source. The photoluminescence intensity from Ge_1-y Sn_y /Ge films is expected to increase relative to Ge_1-y Sn_y /Si due to the less defected interface with the virtual substrate. However, while Ge_1-y Sn_y /Si films are largely relaxed, a significant amount of compressive strain may be present in the Ge_1-y Sn_y /Ge case. This compressive strain can reduce the emission intensity by increasing the separation between the direct and indirect edges. In this context, it is shown here that the proposed CVD approach to Ge_1-y Sn_y /Ge makes it possible to approach film thicknesses of about 1  μm, for which the strain is mostly relaxed and the photoluminescence intensity increases by one order of magnitude relative to Ge_1-y Sn_y /Si films. The observed strain relaxation is shown to be consistent with predictions from strain-relaxation models first developed for the Si_1-x Ge_x /Si system. The defect structure and atomic distributions in the films are studied in detail using advanced electron-microscopy techniques, including aberration corrected STEM imaging and EELS mapping of the average diamond–cubic lattice.

Background: To be effective, orally administered live Salmonella vaccines must first survive their encounter with the low pH environment of the stomach. To enhance survival, an antacid is often given to neutralize the acidic environment of the stomach just prior to or concomitant with administration of the vaccine. One drawback of this approach, from the perspective of the clinical trial volunteer, is that the taste of a bicarbonate-based acid neutralization system can be unpleasant. Thus, we explored an alternative method that would be at least as effective as bicarbonate and with a potentially more acceptable taste. Because ingestion of protein can rapidly buffer stomach pH, we examined the possibility that the protein-rich Ensure® Nutrition shakes would be effective alternatives to bicarbonate.

Results: We tested one Salmonella enterica serovar Typhimurium and three Salmonella Typhi vaccine strains and found that all strains survived equally well when incubated in either Ensure® or bicarbonate. In a low gastric pH mouse model, Ensure® worked as well or better than bicarbonate to enhance survival through the intestinal tract, although neither agent enhanced the survival of the S. Typhi test strain possessing a rpoS mutation.

Conclusions: Our data show that a protein-rich drink such as Ensure® Nutrition shakes can serve as an alternative to bicarbonate for reducing gastric pH prior to administration of a live Salmonella vaccine.

The emission properties of GeSn heterostructure pin diodes have been investigated. The devices contain thick (400–600 nm) Ge_1-y Sn_y i-layers spanning a broad compositional range below and above the crossover Sn concentration y_c where the Ge_1-y Sn_y alloy becomes a direct-gap material. These results are made possible by an optimized device architecture containing a single defected interface thereby mitigating the deleterious effects of mismatch-induced defects. The observed emission intensities as a function of composition show the contributions from two separate trends: an increase in direct gap emission as the Sn concentration is increased, as expected from the reduction and eventual reversal of the separation between the direct and indirect edges, and a parallel increase in non-radiative recombination when the mismatch strains between the structure components is partially relaxed by the generation of misfit dislocations. An estimation of recombination times based on the observed electroluminescence intensities is found to be strongly correlated with the reverse-bias dark current measured in the same devices.

The development of non-volatile logic through direct coupling of spontaneous ferroelectric polarization with semiconductor charge carriers is nontrivial, with many issues, including epitaxial ferroelectric growth, demonstration of ferroelectric switching and measurable semiconductor modulation. Here we report a true ferroelectric field effect—carrier density modulation in an underlying Ge(001) substrate by switching of the ferroelectric polarization in epitaxial c-axis-oriented BaTiO₃ grown by molecular beam epitaxy. Using the density functional theory, we demonstrate that switching of BaTiO₃ polarization results in a large electric potential change in Ge. Aberration-corrected electron microscopy confirms BaTiO₃ tetragonality and the absence of any low-permittivity interlayer at the interface with Ge. The non-volatile, switchable nature of the single-domain out-of-plane ferroelectric polarization of BaTiO₃ is confirmed using piezoelectric force microscopy. The effect of the polarization switching on the conductivity of the underlying Ge is measured using microwave impedance microscopy, clearly demonstrating a ferroelectric field effect.