Theses and Dissertations
This collection includes both ASU Theses and Dissertations, submitted by graduate students, and the Barrett, Honors College theses submitted by undergraduate students.
Displaying 1 - 2 of 2
Filtering by
- Creators: Diaz, Rodolfo
- Creators: Korobeinikov, Yuri
Description
Programmable Metallization Cell (PMC) is a resistance-switching device based on migration of nanoscale quantities of cations in a solid electrolyte and formation of a conducting electrodeposit by the reductions of these cations. This dissertation presents electrical characterization results on Cu-SiO2 based PMC devices, which due to the na- ture of materials can be easily integrated into the current Complimentary metal oxide semiconductor (CMOS) process line. Device structures representing individual mem- ory cells based on W bottom electrode and n-type Si bottom electrode were fabricated for characterization. For the W bottom electrode based devices, switching was ob- served for voltages in the range of 500mV and current value as low as 100 nA showing the electrochemical nature and low power potential. The ON state showed a direct de- pendence on the programming current, showing the possibility of multi-bit storage in a single cell. Room temperature retention was demonstrated in excess of 105 seconds and endurance to approximately 107 cycles. Switching was observed for microsecond duration 3 V amplitude pulses. Material characterization results from Raman, X-ray diffraction, Rutherford backscattering and Secondary-ion mass spectroscopy analysis shows the influence of processing conditions on the Cu concentration within the film and also the presence of Cu as free atoms. The results seemed to indicate stress-induced void formation in the SiO2 matrix as the driving mechanism for Cu diffusion into the SiO2 film. Cu/SiO2
Si based PMC devices were characterized and were shown to have inherent isolation characteristics, proving the feasibility of such a structure for a passive array. The inherent isolation property simplifies fabrication by avoiding the need for a separate diode element in an array. The isolation characteristics were studied mainly in terms of the leakage current. The nature of the diode interface was further studied by extracting a barrier potential which shows it can be approximated to a Cu-nSi metal semiconductor Schottky diode.
Si based PMC devices were characterized and were shown to have inherent isolation characteristics, proving the feasibility of such a structure for a passive array. The inherent isolation property simplifies fabrication by avoiding the need for a separate diode element in an array. The isolation characteristics were studied mainly in terms of the leakage current. The nature of the diode interface was further studied by extracting a barrier potential which shows it can be approximated to a Cu-nSi metal semiconductor Schottky diode.
ContributorsPuthenthermadam, Sarath (Author) / Kozicki, Michael N (Thesis advisor) / Diaz, Rodolfo (Committee member) / Schroder, Dieter K. (Committee member) / Alford, Terry (Committee member) / Arizona State University (Publisher)
Created2011
Description
The characterization of interface properties in molten slag is crucial for understanding the interface phenomenon and the reactions between slag and metal. This study focuses on examining the influence of Cr2O3, an important surface active oxide, on the wettability and surface tension of slag. Industrial Electric Arc Furnace (EAF) slag with two different Cr2O3 contents (1 wt% and 3 wt%) was investigated using the sessile drop measurement technique at a high temperature of 1650°C. For the preparation of 3 wt% Cr2O3-doped slags, the following crucibles were used: Al2O3, Mo, and MgO. The behavior of crucibles, the dissolution process as well as its effect on the slag thermophysical properties were studied. For the evaluation of surface tension, Mo and MgO substrates were used. The contact angle was measured using the sessile drop method, and the surface tension was calculated using the Young-Laplace-based software. The interaction and wettability behavior between the slag and different substrates was studied. The effects of Cr2O3 content, in correlation with Al2O3, Mo, and MgO, as well as temperature, on the surface tension, and phase formation were analyzed using FactSage 8.2. The results indicate an increase in the formation of solid phases with Al2O3 and Mo dissolution into the slag. The composition of the MoO3 is confirmed with the XRF and EDS analysis. Furthermore, an increase in the formation of the spinel phase was observed with the addition of chromium, which is confirmed via XRD. The increase in the CaCrMo-oxide-based spinel led to a decrease in the surface tension of the slag. The surface tension of the slag pre-melted in a Mo, decreases as the Cr2O3 content increases. The effects of the amounts of Cr2O3 in correlation with Al2O3, MgO, and MoO3 on the slag foaming index were determined using the existing models in the literature.
ContributorsMeena, Neha (Author) / Seetharaman, Sridhar (Thesis advisor) / Alford, Terry (Committee member) / Korobeinikov, Yuri (Committee member) / Arizona State University (Publisher)
Created2023