Theses and Dissertations
This collection includes both ASU Theses and Dissertations, submitted by graduate students, and the Barrett, Honors College theses submitted by undergraduate students.
Displaying 1 - 10 of 158
Description
Recently, the use of zinc oxide (ZnO) nanowires as an interphase in composite materials has been demonstrated to increase the interfacial shear strength between carbon fiber and an epoxy matrix. In this research work, the strong adhesion between ZnO and carbon fiber is investigated to elucidate the interactions at the interface that result in high interfacial strength. First, molecular dynamics (MD) simulations are performed to calculate the adhesive energy between bare carbon and ZnO. Since the carbon fiber surface has oxygen functional groups, these were modeled and MD simulations showed the preference of ketones to strongly interact with ZnO, however, this was not observed in the case of hydroxyls and carboxylic acid. It was also found that the ketone molecules ability to change orientation facilitated the interactions with the ZnO surface. Experimentally, the atomic force microscope (AFM) was used to measure the adhesive energy between ZnO and carbon through a liftoff test by employing highly oriented pyrolytic graphite (HOPG) substrate and a ZnO covered AFM tip. Oxygen functionalization of the HOPG surface shows the increase of adhesive energy. Additionally, the surface of ZnO was modified to hold a negative charge, which demonstrated an increase in the adhesive energy. This increase in adhesion resulted from increased induction forces given the relatively high polarizability of HOPG and the preservation of the charge on ZnO surface. It was found that the additional negative charge can be preserved on the ZnO surface because there is an energy barrier since carbon and ZnO form a Schottky contact. Other materials with the same ionic properties of ZnO but with higher polarizability also demonstrated good adhesion to carbon. This result substantiates that their induced interaction can be facilitated not only by the polarizability of carbon but by any of the materials at the interface. The versatility to modify the magnitude of the induced interaction between carbon and an ionic material provides a new route to create interfaces with controlled interfacial strength.
ContributorsGalan Vera, Magdian Ulises (Author) / Sodano, Henry A (Thesis advisor) / Jiang, Hanqing (Committee member) / Solanki, Kiran (Committee member) / Oswald, Jay (Committee member) / Speyer, Gil (Committee member) / Arizona State University (Publisher)
Created2013
Description
The overall goal of this research project was to assess the feasibility of investigating the effects of microgravity on mineralization systems in unit gravity environments. If possible to perform these studies in unit gravity earth environments, such as earth, such systems can offer markedly less costly and more concerted research efforts to study these vitally important systems. Expected outcomes from easily accessible test environments and more tractable studies include the development of more advanced and adaptive material systems, including biological systems, particularly as humans ponder human exploration in deep space. The specific focus of the research was the design and development of a prototypical experimental test system that could preliminarily meet the challenging design specifications required of such test systems. Guided by a more unified theoretical foundation and building upon concept design and development heuristics, assessment of the feasibility of two experimental test systems was explored. Test System I was a rotating wall reactor experimental system that closely followed the specifications of a similar test system, Synthecon, designed by NASA contractors and thus closely mimicked microgravity conditions of the space shuttle and station. The latter includes terminal velocity conditions experienced by both innate material systems, as well as, biological systems, including living tissue and humans but has the ability to extend to include those material test systems associated with mineralization processes. Test System II is comprised of a unique vertical column design that offered more easily controlled fluid mechanical test conditions over a much wider flow regime that was necessary to achieving terminal velocities under free convection-less conditions that are important in mineralization processes. Preliminary results indicate that Test System II offers distinct advantages in studying microgravity effects in test systems operating in unit gravity environments and particularly when investigating mineralization and related processes. Verification of the Test System II was performed on validating microgravity effects on calcite mineralization processes reported earlier others. There studies were conducted on calcite mineralization in fixed-wing, reduced gravity aircraft, known as the `vomit comet' where reduced gravity conditions are include for very short (~20second) time periods. Preliminary results indicate that test systems, such as test system II, can be devised to assess microgravity conditions in unit gravity environments, such as earth. Furthermore, the preliminary data obtained on calcite formation suggest that strictly physicochemical mechanisms may be the dominant factors that control adaptation in materials processes, a theory first proposed by Liu et al. Thus the result of this study may also help shine a light on the problem of early osteoporosis in astronauts and long term interest in deep space exploration.
ContributorsSeyedmadani, Kimia (Author) / Pizziconi, Vincent (Thesis advisor) / Towe, Bruce (Committee member) / Alford, Terry (Committee member) / Arizona State University (Publisher)
Created2013
Description
As crystalline silicon solar cells continue to get thinner, the recombination of carriers at the surfaces of the cell plays an ever-important role in controlling the cell efficiency. One tool to minimize surface recombination is field effect passivation from the charges present in the thin films applied on the cell surfaces. The focus of this work is to understand the properties of charges present in the SiNx films and then to develop a mechanism to manipulate the polarity of charges to either negative or positive based on the end-application. Specific silicon-nitrogen dangling bonds (·Si-N), known as K center defects, are the primary charge trapping defects present in the SiNx films. A custom built corona charging tool was used to externally inject positive or negative charges in the SiNx film. Detailed Capacitance-Voltage (C-V) measurements taken on corona charged SiNx samples confirmed the presence of a net positive or negative charge density, as high as +/- 8 x 1012 cm-2, present in the SiNx film. High-energy (~ 4.9 eV) UV radiation was used to control and neutralize the charges in the SiNx films. Electron-Spin-Resonance (ESR) technique was used to detect and quantify the density of neutral K0 defects that are paramagnetically active. The density of the neutral K0 defects increased after UV treatment and decreased after high temperature annealing and charging treatments. Etch-back C-V measurements on SiNx films showed that the K centers are spread throughout the bulk of the SiNx film and not just near the SiNx-Si interface. It was also shown that the negative injected charges in the SiNx film were stable and present even after 1 year under indoor room-temperature conditions. Lastly, a stack of SiO2/SiNx dielectric layers applicable to standard commercial solar cells was developed using a low temperature (< 400 °C) PECVD process. Excellent surface passivation on FZ and CZ Si substrates for both n- and p-type samples was achieved by manipulating and controlling the charge in SiNx films.
ContributorsSharma, Vivek (Author) / Bowden, Stuart (Thesis advisor) / Schroder, Dieter (Committee member) / Honsberg, Christiana (Committee member) / Roedel, Ronald (Committee member) / Alford, Terry (Committee member) / Arizona State University (Publisher)
Created2013
Description
Microwave dielectrics are widely used to make resonators and filters in telecommunication systems. The production of thin films with high dielectric constant and low loss could potentially enable a marked reduction in the size of devices and systems. However, studies of these materials in thin film form are very sparse. In this research, experiments were carried out on practical high-performance dielectrics including ZrTiO4-ZnNb2O6 (ZTZN) and Ba(Co,Zn)1/3Nb2/3O3 (BCZN) with high dielectric constant and low loss tangent. Thin films were deposited by laser ablation on various substrates, with a systematical study of growth conditions like substrate temperature, oxygen pressure and annealing to optimize the film quality, and the compositional, microstructural, optical and electric properties were characterized. The deposited ZTZN films were randomly oriented polycrystalline on Si substrate and textured on MgO substrate with a tetragonal lattice change at elevated temperature. The BCZN films deposited on MgO substrate showed superior film quality relative to that on other substrates, which grow epitaxially with an orientation of (001) // MgO (001) and (100) // MgO (100) when substrate temperature was above 500 oC. In-situ annealing at growth temperature in 200 mTorr oxygen pressure was found to enhance the quality of the films, reducing the peak width of the X-ray Diffraction (XRD) rocking curve to 0.53o and the χmin of channeling Rutherford Backscattering Spectrometry (RBS) to 8.8% when grown at 800oC. Atomic Force Microscopy (AFM) was used to study the topography and found a monotonic decrease in the surface roughness when the growth temperature increased. Optical absorption and transmission measurements were used to determine the energy bandgap and the refractive index respectively. A low-frequency dielectric constant of 34 was measured using a planar interdigital measurement structure. The resistivity of the film is ~3×1010 ohm·cm at room temperature and has an activation energy of thermal activated current of 0.66 eV.
ContributorsLi, You (Author) / Newman, Nathan (Thesis advisor) / Alford, Terry (Committee member) / Singh, Rakesh (Committee member) / Arizona State University (Publisher)
Created2013
Description
This dissertation explores the role of smart home service provisions (SHSP) as motivational agents supporting goal attainment and human flourishing. Evoking human flourishing as a lens for interaction encapsulates issues of wellbeing, adaptation and problem solving within the context of social interaction. To investigate this line of research a new, motivation-sensitive approach to design was implemented. This approach combined psychometric analysis from motivational psychology's Personal Project Analysis (PPA) and Place Attachment theory's Sense of Place (SoP) analysis to produce project-centered motivational models for environmental congruence. Regression analysis of surveys collected from 150 (n = 150) young adults about their homes revealed PPA motivational dimensions had significant main affects on all three SoP factors. Model one indicated PPA dimensions Fearful and Value Congruency predicted the SoP factor Place Attachment (p = 0.012). Model two indicated the PPA factor Positive Affect and PPA dimensions Value Congruency, Self Identity and Autonomy predicted Place Identity (p = .0003). Model three indicated PPA dimensions Difficulty and Likelihood of Success predicted the SoP factor Place Dependency. The relationships between motivational PPA dimensions and SoP demonstrated in these models informed creation of a set of motivational design heuristics. These heuristics guided 20 participants (n = 20) through co-design of paper prototypes of SHSPs supporting goal attainment and human flourishing. Normative analysis of these paper prototypes fashioned a design framework consisting of the use cases "make with me", "keep me on task" and "improve myself"; the four design principles "time and timing", "guidance and accountability", "project ambiguity" and "positivity mechanisms"; and the seven interaction models "structuring time", "prompt user", "gather resources", "consume content", "create content", "restrict and/or restore access to content" and "share content". This design framework described and evaluated three technology probes installed in the homes of three participants (n = 3) for field-testing over the course of one week. A priori and post priori samples of psychometric measures were inconclusive in determining if SHSP motivated goal attainment or increased environmental congruency between young adults and their homes.
ContributorsBrotman, Ryan Scott (Author) / Burleson, Winsow (Thesis advisor) / Heywood, William (Committee member) / Forlizzi, Jodi (Committee member) / Arizona State University (Publisher)
Created2013
Description
Research has shown that the ability to smell is the most direct sense an individual can experience. With every breath a person takes, the brain recognizes thousands of molecules and makes connections with our memories to determine their composition. With the amount of research looking into how and why we smell, researchers still have little understanding of how the nose and brain process an aroma, and how emotional and physical behavior is impacted. This research focused on the affects smell has on a caregiver in a simulated Emergency Department setting located in the SimET of Banner Good Samaritan Medical Center in Phoenix, Arizona. The study asked each participant to care for a programmed mannequin, or "patient", while performing simple computer-based tasks, including memory and recall, multi-tasking, and mood-mapping to gauge physical and mental performance. Three different aromatic environments were then introduced through diffusion and indirect inhalation near the participants' task space: 1) a control (no smell), 2) an odor (simulated dirty feet), and 3) an aroma (one of four true essential oils plus a current odor-eliminating compound used in many U.S. Emergency Departments). This study was meant to produce a stressful environment by leading the caregiver to stay in constant movement throughout the study through timed tasks, uncooperative equipment, and a needy "patient". The goal of this research was to determine if smells, and of what form of pleasantness and repulsiveness, can have an effect on the physical and mental performance of emergency caregivers. Findings from this study indicated that the "odor eliminating" method currently used in typical Emergency Departments, coffee grounds, is more problematic than helpful, and the introduction of true essential oils may not only reduce stress, but increase efficiency and, in turn, job satisfaction.
ContributorsClark, Carina M (Author) / Bernardi, Jose (Thesis advisor) / Heywood, William (Committee member) / Watts, Richard (Committee member) / Rosso, Rachel (Committee member) / Arizona State University (Publisher)
Created2013
Description
A growing body of research shows that characteristics of the built environment in healthcare facilities impact patients' well-being. Research findings suggest that patients form judgments of perceived quality care based on environmental characteristics. Patient outcomes and ratings of quality of care are linked to the environments' ability to reduce patient stress as well as influence perceptions of quality of care. Historically, this research has been focused in the hospital environment. The United States healthcare system heavily relies on hospitals to treat (rather than prevent) illness, leading to a high per capita healthcare expenditure. Currently, this healthcare system is shifting to rely heavily on ambulatory care settings and primary care providers to detect, prevent, and manage expensive medical conditions. The highest rates of preventable disease and the lowest rates of primary care usage are found in the young adult population (ages 18 to 24). More than any other patient population, this segment rates their satisfaction with healthcare significantly low. For this population education, early detection, and monitoring will be key for a primary care focused model to have the greatest impact on care and long-term savings. Strong patient-physician connections ensure the success of a primary care focused model. The physical environment has the opportunity to provide a message consistent with a physician's practice values and goals. Environmental cues in the waiting area have the potential to relay these messages to the patient prior to physician contact. Through an understanding and optimization of these cues patient perception of quality of care may be increased, thus improving the patient-physician relationship. This study provides insight on how to optimize environmental impact on the healthcare experience. This descriptive exploratory study utilized a non-verbal self-report instrument to collect demographic information and measure participant's responses to two panoramic photos of primary care provider waiting areas. Respondents were asked to identify physical elements in the photos that contributed to their perceptions of the quality of care to be expected. The sample population consisted of 33, 18 to 24 year-olds leaving a total of 234 emotional markers and comments. Qualitative and quantitative revealed three key themes of appeal, comfort, and regard. Physical elements, in the photos, related to the themes include: General areas that were important to the respondents were the seating and reception areas, as well as the overall appearance of the waiting area. Key elements identified to be significant characteristics influencing perceptions of quality of care are presented in this study.
ContributorsBadura, Kerri (Author) / Lamb, Gerri (Thesis advisor) / Heywood, William (Committee member) / Wolf, Peter (Committee member) / Arizona State University (Publisher)
Created2012
Description
Ball Grid Array (BGA) using lead-free or lead-rich solder materials are widely used as Second Level Interconnects (SLI) in mounting packaged components to the printed circuit board (PCB). The reliability of these solder joints is of significant importance to the performance of microelectronics components and systems. Product design/form-factor, solder material, manufacturing process, use condition, as well as, the inherent variabilities present in the system, greatly influence product reliability. Accurate reliability analysis requires an integrated approach to concurrently account for all these factors and their synergistic effects. Such an integrated and robust methodology can be used in design and development of new and advanced microelectronics systems and can provide significant improvement in cycle-time, cost, and reliability. IMPRPK approach is based on a probabilistic methodology, focusing on three major tasks of (1) Characterization of BGA solder joints to identify failure mechanisms and obtain statistical data, (2) Finite Element analysis (FEM) to predict system response needed for life prediction, and (3) development of a probabilistic methodology to predict the reliability, as well as, the sensitivity of the system to various parameters and the variabilities. These tasks and the predictive capabilities of IMPRPK in microelectronic reliability analysis are discussed.
ContributorsFallah-Adl, Ali (Author) / Tasooji, Amaneh (Thesis advisor) / Krause, Stephen (Committee member) / Alford, Terry (Committee member) / Jiang, Hanqing (Committee member) / Mahajan, Ravi (Committee member) / Arizona State University (Publisher)
Created2013
Description
Shock loading is a complex phenomenon that can lead to failure mechanisms such as strain localization, void nucleation and growth, and eventually spall fracture. Studying incipient stages of spall damage is of paramount importance to accurately determine initiation sites in the material microstructure where damage will nucleate and grow and to formulate continuum models that account for the variability of the damage process due to microstructural heterogeneity. The length scale of damage with respect to that of the surrounding microstructure has proven to be a key aspect in determining sites of failure initiation. Correlations have been found between the damage sites and the surrounding microstructure to determine the preferred sites of spall damage, since it tends to localize at and around the regions of intrinsic defects such as grain boundaries and triple points. However, considerable amount of work still has to be done in this regard to determine the physics driving the damage at these intrinsic weak sites in the microstructure. The main focus of this research work is to understand the physical mechanisms behind the damage localization at these preferred sites. A crystal plasticity constitutive model is implemented with different damage criteria to study the effects of stress concentration and strain localization at the grain boundaries. A cohesive zone modeling technique is used to include the intrinsic strength of the grain boundaries in the simulations. The constitutive model is verified using single elements tests, calibrated using single crystal impact experiments and validated using bicrystal and multicrystal impact experiments. The results indicate that strain localization is the predominant driving force for damage initiation and evolution. The microstructural effects on theses damage sites are studied to attribute the extent of damage to microstructural features such as grain orientation, misorientation, Taylor factor and the grain boundary planes. The finite element simulations show good correlation with the experimental results and can be used as the preliminary step in developing accurate probabilistic models for damage nucleation.
ContributorsKrishnan, Kapil (Author) / Peralta, Pedro (Thesis advisor) / Mignolet, Marc (Committee member) / Sieradzki, Karl (Committee member) / Jiang, Hanqing (Committee member) / Oswald, Jay (Committee member) / Arizona State University (Publisher)
Created2013
Description
Generally speaking, many programs of interior design have had a gender imbalance in the student population. As a case in point, the interior design program at Arizona State University (ASU) is at present ninety percent female. While other design programs such as architecture or industrial design have achieved gender balance, interior design has not. This research explores the reasons why male students are not enrolling in the interior design program at ASU and to what degree gender influences the selection of a major. The objectives of this research are to determine: 1) what role gender plays in the selection of interior design as a choice of a major at ASU; 2) why might male students be hesitant to join the interior design program; 3) why female students are attracted to interior design; 4) if there are gender differences in design approach; and 5) if curricular differences between interior architecture and interior design impact the gender imbalance. A mixed method approach is used in order to answer the research questions including: a literature review, a visual ethnography, and interviews of interior design students and faculty members at ASU. The results reveal that gender might have an effect on students' decision to join the interior design program. For a male student, people questioned his sexuality because they assumed he would have to be of a certain sexual orientation to study interior design. According to a male faculty member upon visiting a middle school on career day, young boys would be interested in the projects displayed at the interior design booth until they figured out what it was. Even at a young age, the boys seemed to know that interior design was a female's domain. A participant stated that women seemed to be less critical of the men's projects and were more critical of each other. A male respondent stated that on the occasion there were no men in the class the studio culture changed. Another stated that interior design students did not take feedback as well as others and need to be affirmed more often. Gender socialization, the history of interior design as a feminine career, and the title "interior design" itself are all possible factors that could deter male students from joining the program. The insights acquired from this research will provide students and faculty members from The Design School and beyond a better understanding of gender socialization and what the interior design program has to offer.
ContributorsRuff, Charlene (Author) / Giard, Jacques (Thesis advisor) / Heywood, William (Committee member) / Margolis, Eric (Committee member) / Arizona State University (Publisher)
Created2014