Theses and Dissertations
This collection includes both ASU Theses and Dissertations, submitted by graduate students, and the Barrett, Honors College theses submitted by undergraduate students.
Displaying 1 - 3 of 3
Filtering by
- Creators: Peralta, Pedro
Description
Microstructure refinement and alloy additions are considered potential routes to increase high temperature performance of existing metallic superalloys used under extreme conditions. Nanocrystalline (NC) Cu-10at%Ta exhibits such improvements over microstructurally unstable NC metals, leading to enhanced creep behavior compared to its coarse-grained (CG) counterparts. However, the low melting point of Cu compared to other FCC metals, e.g., Ni, might lead to an early onset of diffusional creep mechanisms. Thus, this research seeks to study the thermo-mechanical behavior and stability of hierarchical (prepared using arc-melting) and NC (prepared by collaborators through powder pressing and annealing) Ni-Y-Zr alloys where Zr is expected to provide solid solution and grain boundary strengthening in hierarchical and NC alloys, respectively, while Ni-Y and Ni-Zr intermetallic precipitates (IMCs) would provide kinetic stability. Hierarchical alloys had microstructures stable up to 1100 °C with ultrafine eutectic of ~300 nm, dendritic arm spacing of ~10 μm, and grain size ~1-2 mm. Room temperature hardness tests along with uniaxial compression performed at 25 and 600 °C revealed that microhardness and yield strength of hierarchical alloys with small amounts of Y (0.5-1wt%) and Zr (1.5-3 wt%) were comparable to Ni-superalloys, due to the hierarchical microstructure and potential presence of nanoscale IMCs. In contrast, NC alloys of the same composition were found to be twice as hard as the hierarchical alloys. Creep tests at 0.5 homologous temperature showed active Coble creep mechanisms in hierarchical alloys at low stresses with creep rates slower than Fe-based superalloys and dislocation creep mechanisms at higher stresses. Creep in NC alloys at lower stresses was only 20 times faster than hierarchical alloys, with the difference in grain size ranging from 10^3 to 10^6 times at the same temperature. These NC alloys showed enhanced creep properties over other NC metals and are expected to have rates equal to or improved over the CG hierarchical alloys with ECAP processing techniques. Lastly, the in-situ wide-angle x-ray scattering (WAXS) measurements during quasi-static and creep tests implied stresses being carried mostly by the matrix before yielding and in the primary creep stage, respectively, while relaxation was observed in Ni5Zr for both hierarchical and NC alloys. Beyond yielding and in the secondary creep stage, lattice strains reached a steady state, thereby, an equilibrium between plastic strain rates was achieved across different phases, so that deformation reaches a saturation state where strain hardening effects are compensated by recovery mechanisms.
ContributorsSharma, Shruti (Author) / Peralta, Pedro (Thesis advisor) / Alford, Terry (Committee member) / Jiao, Yang (Committee member) / Solanki, Kiran (Committee member) / Arizona State University (Publisher)
Created2022
Description
Solid-state and non-equilibrium processings are of great interest to researchers due to their ability to control and refine bulk and/or surface microstructure of metallic alloys and push them to surpass their conventional properties limit. In this dissertation, solid-state processing i.e., Shear Assisted Processing and Extrusion (ShAPE), and non-equilibrium processes i.e., surface mechanical attrition (SMAT) and additive manufacturing (AM) techniques were used to process the magnesium and aluminum alloys respectively. A synergistic investigation of processing-induced microstructural modification and its effect on corrosion resistance was performed using various ex-situ, quasi in-situ, and in-situ electrochemical, microscopy, and spectroscopy characterization techniques. To evaluate the effect of the same processing condition on a range of microstructures, a variety of magnesium alloys such as AZ31B, Mg-3Si, ZK60, and Pure Mg were processed using a novel solid-state processing method, namely ShAPE. It induced a significant grain refinement, homogenized distribution of second phases, and low residual strain in AZ31B alloy, which contributed toward a noble breakdown potential, stable protective film, and hence better corrosion resistance compared to the parent extruded counterpart. However, with variations in composition, volume fraction, and distribution of second phases with Mg-3Si and ZK60 magnesium alloy an opposite response was inferred indicating a strong dependence of corrosion on underlying microstructure compared to a processing condition. Non-equilibrium processes, i.e. SMAT and AM were utilized to process high-strength 7xxx series aluminum alloys. Continuous high energy impacts of hard balls in room temperature (RT SMAT) and liquid nitrogen (LN2 SMAT) flow environment generated a gradient nanocrystalline surface layer with the dissolution of inherent second phase and precipitation of new phases in aluminum 7075 alloys. RT SMAT showed a reduced anodic dissolution rate and improved film resistance, which was attributed to the thicker and composite oxide layer along with new nanoscale precipitates. Lastly, reactive AM was used to process aluminum 7075 and 7050 alloys which resulted in a refined and textureless microstructure. A reduction in corrosion resistance was observed with precipitation of excessive reactive particles (Ti and B4C) in AM alloys compared to wrought counterparts.
ContributorsBeura, Vikrant Kumar (Author) / Solanki, Kiran N (Thesis advisor) / Peralta, Pedro (Committee member) / Alford, Terry (Committee member) / Ankit, Kumar (Committee member) / Joshi, Vineet V (Committee member) / Arizona State University (Publisher)
Created2022
Description
Nanocrystalline (NC) materials are of great interest to researchers due to their multitude of properties such as exceptional strength and radiation resistance owing to their high fraction of grain boundaries that act as defect sinks for radiation-induced defects, provided they are microstructurally stable. In this dissertation, radiation effects in microstructurally stable bulk NC copper (Cu)- tantalum (Ta) alloys engineered with uniformly dispersed Ta nano-precipitates are systematically probed. Towards this, both ex-situ and in-situ irradiations using heavy (self) ion, helium ion, and concurrent dual ion beams (He+Au) followed by isochronal annealing inside TEM were utilized to understand radiation tolerance and underlying mechanisms of microstructure evolution in stable NC alloys. With systematic self-ion irradiation, the high density of tantalum nanoclusters in Cu-10at.%Ta were observed to act as stable sinks in suppressing radiation hardening, in addition to stabilizing the grain boundaries; while the large incoherent precipitates experienced ballistic mixing and dissolution at high doses. Interestingly, the alloy exhibited a microstructure self-healing mechanism, where with a moderate thermal input, this dissolved tantalum eventually re-precipitated, thus replenishing the sink density. The high stability of these tantalum nanoclusters is attributed to the high positive enthalpy of mixing of tantalum in copper which also acted as a critical driving force against atomic mixing to facilitate re-precipitation of tantalum nanoclusters. Furthermore, these nanoclusters proved to be effective trapping sites for helium, thus sequestering helium into isolated small bubbles and aid in increasing the overall swelling threshold of the alloy. The alloy was then compositionally optimized to reduce the density of large incoherent precipitates without compromising on the grain size and nanocluster density (Cu-3at.%Ta) which resulted in a consistent and more promising response to high dose self-ion irradiation. In-situ helium and dual beam irradiation coupled with isochronal annealing till 723 K, also revealed a comparable microstructural stability and enhanced ability of Cu-3Ta in controlling bubble growth and suppressing swelling compared to Cu-10Ta indicating a promising improvement in radiation tolerance in the optimized composition. Overall, this work helps advancing the current understanding of radiation tolerance in stable nanocrystalline alloys and aid developing design strategies for engineering radiation tolerant materials with stable interfaces.
ContributorsSrinivasan, Soundarya (Author) / Solanki, Kiran (Thesis advisor) / Peralta, Pedro (Committee member) / Alford, Terry (Committee member) / Darling, Kristopher (Committee member) / Arizona State University (Publisher)
Created2021