Theses and Dissertations
Displaying 1 - 4 of 4
Filtering by
- All Subjects: Analytical Modeling
- All Subjects: Internet of Things
Description
Process variations have become increasingly important for scaled technologies starting at 45nm. The increased variations are primarily due to random dopant fluctuations, line-edge roughness and oxide thickness fluctuation. These variations greatly impact all aspects of circuit performance and pose a grand challenge to future robust IC design. To improve robustness, efficient methodology is required that considers effect of variations in the design flow. Analyzing timing variability of complex circuits with HSPICE simulations is very time consuming. This thesis proposes an analytical model to predict variability in CMOS circuits that is quick and accurate. There are several analytical models to estimate nominal delay performance but very little work has been done to accurately model delay variability. The proposed model is comprehensive and estimates nominal delay and variability as a function of transistor width, load capacitance and transition time. First, models are developed for library gates and the accuracy of the models is verified with HSPICE simulations for 45nm and 32nm technology nodes. The difference between predicted and simulated σ/μ for the library gates is less than 1%. Next, the accuracy of the model for nominal delay is verified for larger circuits including ISCAS'85 benchmark circuits. The model predicted results are within 4% error of HSPICE simulated results and take a small fraction of the time, for 45nm technology. Delay variability is analyzed for various paths and it is observed that non-critical paths can become critical because of Vth variation. Variability on shortest paths show that rate of hold violations increase enormously with increasing Vth variation.
ContributorsGummalla, Samatha (Author) / Chakrabarti, Chaitali (Thesis advisor) / Cao, Yu (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2011
Description
As integrated technologies are scaling down, there is an increasing trend in the
process,voltage and temperature (PVT) variations of highly integrated RF systems.
Accounting for these variations during the design phase requires tremendous amount
of time for prediction of RF performance and optimizing it accordingly. Thus, there
is an increasing gap between the need to relax the RF performance requirements at
the design phase for rapid development and the need to provide high performance
and low cost RF circuits that function with PVT variations. No matter how care-
fully designed, RF integrated circuits (ICs) manufactured with advanced technology
nodes necessitate lengthy post-production calibration and test cycles with expensive
RF test instruments. Hence design-for-test (DFT) is proposed for low-cost and fast
measurement of performance parameters during both post-production and in-eld op-
eration. For example, built-in self-test (BIST) is a DFT solution for low-cost on-chip
measurement of RF performance parameters. In this dissertation, three aspects of
automated test and calibration, including DFT mathematical model, BIST hardware
and built-in calibration are covered for RF front-end blocks.
First, the theoretical foundation of a post-production test of RF integrated phased
array antennas is proposed by developing the mathematical model to measure gain
and phase mismatches between antenna elements without any electrical contact. The
proposed technique is fast, cost-efficient and uses near-field measurement of radiated
power from antennas hence, it requires single test setup, it has easy implementation
and it is short in time which makes it viable for industrialized high volume integrated
IC production test.
Second, a BIST model intended for the characterization of I/Q offset, gain and
phase mismatch of IQ transmitters without relying on external equipment is intro-
duced. The proposed BIST method is based on on-chip amplitude measurement as
in prior works however,here the variations in the BIST circuit do not affect the target
parameter estimation accuracy since measurements are designed to be relative. The
BIST circuit is implemented in 130nm technology and can be used for post-production
and in-field calibration.
Third, a programmable low noise amplifier (LNA) is proposed which is adaptable
to different application scenarios depending on the specification requirements. Its
performance is optimized with regards to required specifications e.g. distance, power
consumption, BER, data rate, etc.The statistical modeling is used to capture the
correlations among measured performance parameters and calibration modes for fast
adaptation. Machine learning technique is used to capture these non-linear correlations and build the probability distribution of a target parameter based on measurement results of the correlated parameters. The proposed concept is demonstrated by
embedding built-in tuning knobs in LNA design in 130nm technology. The tuning
knobs are carefully designed to provide independent combinations of important per-
formance parameters such as gain and linearity. Minimum number of switches are
used to provide the desired tuning range without a need for an external analog input.
process,voltage and temperature (PVT) variations of highly integrated RF systems.
Accounting for these variations during the design phase requires tremendous amount
of time for prediction of RF performance and optimizing it accordingly. Thus, there
is an increasing gap between the need to relax the RF performance requirements at
the design phase for rapid development and the need to provide high performance
and low cost RF circuits that function with PVT variations. No matter how care-
fully designed, RF integrated circuits (ICs) manufactured with advanced technology
nodes necessitate lengthy post-production calibration and test cycles with expensive
RF test instruments. Hence design-for-test (DFT) is proposed for low-cost and fast
measurement of performance parameters during both post-production and in-eld op-
eration. For example, built-in self-test (BIST) is a DFT solution for low-cost on-chip
measurement of RF performance parameters. In this dissertation, three aspects of
automated test and calibration, including DFT mathematical model, BIST hardware
and built-in calibration are covered for RF front-end blocks.
First, the theoretical foundation of a post-production test of RF integrated phased
array antennas is proposed by developing the mathematical model to measure gain
and phase mismatches between antenna elements without any electrical contact. The
proposed technique is fast, cost-efficient and uses near-field measurement of radiated
power from antennas hence, it requires single test setup, it has easy implementation
and it is short in time which makes it viable for industrialized high volume integrated
IC production test.
Second, a BIST model intended for the characterization of I/Q offset, gain and
phase mismatch of IQ transmitters without relying on external equipment is intro-
duced. The proposed BIST method is based on on-chip amplitude measurement as
in prior works however,here the variations in the BIST circuit do not affect the target
parameter estimation accuracy since measurements are designed to be relative. The
BIST circuit is implemented in 130nm technology and can be used for post-production
and in-field calibration.
Third, a programmable low noise amplifier (LNA) is proposed which is adaptable
to different application scenarios depending on the specification requirements. Its
performance is optimized with regards to required specifications e.g. distance, power
consumption, BER, data rate, etc.The statistical modeling is used to capture the
correlations among measured performance parameters and calibration modes for fast
adaptation. Machine learning technique is used to capture these non-linear correlations and build the probability distribution of a target parameter based on measurement results of the correlated parameters. The proposed concept is demonstrated by
embedding built-in tuning knobs in LNA design in 130nm technology. The tuning
knobs are carefully designed to provide independent combinations of important per-
formance parameters such as gain and linearity. Minimum number of switches are
used to provide the desired tuning range without a need for an external analog input.
ContributorsShafiee, Maryam (Author) / Ozev, Sule (Thesis advisor) / Diaz, Rodolfo (Committee member) / Ogras, Umit Y. (Committee member) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2018
Description
Internet of Things (IoT) has become a popular topic in industry over the recent years, which describes an ecosystem of internet-connected devices or things that enrich the everyday life by improving our productivity and efficiency. The primary components of the IoT ecosystem are hardware, software and services. While the software and services of IoT system focus on data collection and processing to make decisions, the underlying hardware is responsible for sensing the information, preprocess and transmit it to the servers. Since the IoT ecosystem is still in infancy, there is a great need for rapid prototyping platforms that would help accelerate the hardware design process. However, depending on the target IoT application, different sensors are required to sense the signals such as heart-rate, temperature, pressure, acceleration, etc., and there is a great need for reconfigurable platforms that can prototype different sensor interfacing circuits.
This thesis primarily focuses on two important hardware aspects of an IoT system: (a) an FPAA based reconfigurable sensing front-end system and (b) an FPGA based reconfigurable processing system. To enable reconfiguration capability for any sensor type, Programmable ANalog Device Array (PANDA), a transistor-level analog reconfigurable platform is proposed. CAD tools required for implementation of front-end circuits on the platform are also developed. To demonstrate the capability of the platform on silicon, a small-scale array of 24×25 PANDA cells is fabricated in 65nm technology. Several analog circuit building blocks including amplifiers, bias circuits and filters are prototyped on the platform, which demonstrates the effectiveness of the platform for rapid prototyping IoT sensor interfaces.
IoT systems typically use machine learning algorithms that run on the servers to process the data in order to make decisions. Recently, embedded processors are being used to preprocess the data at the energy-constrained sensor node or at IoT gateway, which saves considerable energy for transmission and bandwidth. Using conventional CPU based systems for implementing the machine learning algorithms is not energy-efficient. Hence an FPGA based hardware accelerator is proposed and an optimization methodology is developed to maximize throughput of any convolutional neural network (CNN) based machine learning algorithm on a resource-constrained FPGA.
This thesis primarily focuses on two important hardware aspects of an IoT system: (a) an FPAA based reconfigurable sensing front-end system and (b) an FPGA based reconfigurable processing system. To enable reconfiguration capability for any sensor type, Programmable ANalog Device Array (PANDA), a transistor-level analog reconfigurable platform is proposed. CAD tools required for implementation of front-end circuits on the platform are also developed. To demonstrate the capability of the platform on silicon, a small-scale array of 24×25 PANDA cells is fabricated in 65nm technology. Several analog circuit building blocks including amplifiers, bias circuits and filters are prototyped on the platform, which demonstrates the effectiveness of the platform for rapid prototyping IoT sensor interfaces.
IoT systems typically use machine learning algorithms that run on the servers to process the data in order to make decisions. Recently, embedded processors are being used to preprocess the data at the energy-constrained sensor node or at IoT gateway, which saves considerable energy for transmission and bandwidth. Using conventional CPU based systems for implementing the machine learning algorithms is not energy-efficient. Hence an FPGA based hardware accelerator is proposed and an optimization methodology is developed to maximize throughput of any convolutional neural network (CNN) based machine learning algorithm on a resource-constrained FPGA.
ContributorsSuda, Naveen (Author) / Cao, Yu (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Yu, Shimeng (Committee member) / Seo, Jae-Sun (Committee member) / Arizona State University (Publisher)
Created2016
Description
This work analyzes and develops a point-of-load (PoL) synchronous buck converter using enhancement-mode Gallium Nitride (e-GaN), with emphasis on optimizing reverse conduction loss by using a well-known technique of placing an anti-parallel Schottky diode across the synchronous power device. This work develops an improved analytical switching model for the GaN-based converter with the Schottky diode using piecewise linear approximations.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
ContributorsKoli, Gauri (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2020