Matching Items (14)
Description
Hydrophobic ionizable organic compounds (HIOCs) like per- and polyfluoroalkyl substances (PFAS), certain pharmaceuticals, and surfactants have been detected in groundwater, wastewater, and drinking water. Anion exchange resin treatment is an effective process for removal of anionic contaminants from water. Spent anion exchange resins are conventionally regenerated with high alcohol by volume (ABV) methanol in solution with brine. While effective for regeneration of resins saturated with inorganic anions such as sulfate, nitrate, and perchlorate, HIOCs prove more resistant to regeneration. This research investigated the efficacy of using novel cosolvent solutions with brine to regenerate resins saturated with organic carboxylate and sulfonate anions to understand the effects cosolvent properties have on regenerative ability. Experiments were conducted on six PFAS compounds to evaluate trends in regeneration for three alcohols. For all PFAS species, equivalent ABV and brine solutions showed greatest regeneration with 1-propanol over ethanol and methanol. Experiments with the pharmaceutical sodium diclofenac were conducted showing similar regeneration of 75% methanol and 25% 1-propanol for equivalent salt concentrations and higher regeneration with 1-propanol than ethanol and methanol for equivalent ABV. A series of experiments with surfactant dodecylbenzene sulfonate determined that the key parameters to determine regeneration of the resin for an alcohol cosolvent solution were cosolvent volume fraction, molar mass, Kow value, solution ionic strength, and dielectric constant. Individual assessments on the cost-effectiveness, flammability, and sustainability of cosolvent solutions point to possible future experiments and opportunities for recycled distillery waste streams as regenerative solutions for anion exchange resin.
ContributorsGraham, Cole David (Author) / Boyer, Treavor H (Thesis advisor) / Conroy-Ben, Otakuye (Committee member) / Garcia Segura, Sergio (Committee member) / Arizona State University (Publisher)
Created2022
Description
Potentiometric instrumentation technologies are widely used across many disciplines of science and engineering providing the ability to measure changes to specific environmental variables through various types of sensor electrodes and selective membranes. However, types I, II, and III potentiometric sensor electrodes are limited by biofouling activity, membrane maintenance, grounding sensitivity, thermodynamic variables, and electromagnetic interference. Further, algorithms embedded into instrumentation hardware have impeded the usefulness of such measurements outside of highly controlled environments. Reliability of accurate measurement using these types of senor electrodes is limited to industrial and lab applications in chemistry and nominally active biological environments. Novel innovations in using exotic materials have improved the usefulness of Type II (e.g. tantalum-rubidium-doped titanium) and Type III (e.g. Nafion™ membranes) sensor electrodes, but those sensors are still limited to measuring a single selective parameter. This scope of work investigates utilizing a novel non-selective membrane, or naturally occurring biofilm membrane, as the active sensing surface of a graphite electrode as a new Type IV potentiometric sensor electrode (e.g., the MiProbE™) in biologically active environments. The analysis herein demonstrates decomposition of these non-selective signals into real-time metabolic activity, measurement of key biochemical processes and environmental condition parameters through classical mathematical analysis methods providing the basis of Potentiomics – the characterization and quantification of biochemical metabolic processes in highly dynamic non-equilibrium states.
ContributorsTaylor, Evan (Author) / Weiss, Taylor L (Thesis advisor) / Brown, Albert F (Committee member) / Boyer, Treavor H (Committee member) / Arizona State University (Publisher)
Created2022
Description
Membrane fouling, especially inorganic fouling, is a significant obstacle to treatinghighly saline brine using membrane distillation (MD). In this study, microbubbles (MBs) were injected into the feed tank of a lab-scale direct contact membrane distillation (DCMD) system, and its effect on permeate flux over time was examined. A synthetic inland reverse osmosis (RO) brine with a high scaling tendency was used as a feed solution. Results showed a sharper flux decline in the absence of MBs compared to when MBs are continuously injected into the feed tank. The introduction of MBs reduced the formation of salt precipitations on the membrane surface, which was the primary cause of the decline in flux. The use of intermittent MBs injection instead of continuous MB injection was evaluated as a way to reduce energy consumption; with a 15 min MBs injection every 2h, similar benefits were found for intermittent injection compared to continuous injection, indicating that providing MBs continuously is not needed to mitigate scale formation. These results show that MBs can be a potential chemical-free method to prevent scaling in desalination systems treating high saline solutions.
ContributorsAlghanayem, Rayan (Author) / Perreault, Francois (Thesis advisor) / Lind, Mary Laura (Committee member) / Sinha, Shahnawaz (Committee member) / Arizona State University (Publisher)
Created2022
Description
Nearly 2.1 billion people around the world to date do not have access to safe drinking water. This study proposes a compact (2-L) upflow photoreactor that uses widely available photocatalysts material, such as titanium dioxide (TiO2) or hexagonal boron nitrate (hBN), to oxidize toxic micropollutants. Photocatalysts, such as TiO2, can create powerful hydroxyl radicals (OH•) under UV irradiation to oxidize and disinfect water with various toxic pollutants present in untreated waters. The study assesses this along with few other photoreactors in terms of their performance with an indicator dye, such as methyl orange (MO), para-chlorobenzoic acid (pCBA), as an intermediate of pesticides, and perfluorooctanoic acid (PFOA), part of the per- and polyfluoroalkyl substances (PFAS), a highly persistent organic contaminant in water. This study also describes the various stages of evolution of this 2-L photoreactor, first using TiO2 coated sand in maintaining a uniform (photocatalyst) bed in suspension along with few other modifications that resulted in a photoreactor with a 3 to 4-fold increase in contact time, is discussed. The final stage of this upflow photoreactor modification resulted in the direct use of photocatalysts as a slurry, which was critical, especially for hBN, which cannot be coated onto the sand particles. During this modification and assessment, a smaller bench-top photoreactor (i.e., collimated beam) was also built and tested. It was primarily used in screening various photocatalysts and operational conditions before assessment at this upflow photoreactor and also at a commercial photoreactor (Purifics Photo-Cat) of a larger scale. Thus, the overall goal of this study is to compare a few of these photoreactors of different designs and scales. This includes a collimated beam (at bench-scale), upflow photoreactor (at testbed scale), and a commercial photoreactor, Photo-Cat (at pilot-scale). This study also discusses the performance of these photoreactors under different operating conditions, which includes evaluating two different photocatalyst types (TiO2 and hBN), variable loading rates, applied UV doses, environment pH, and supplemental peroxide addition (as AOP) and with corresponding EEO values.
ContributorsCao, Jiefei (Author) / Sinha, Shahnawaz (Thesis advisor) / Westerhoff, Paul (Committee member) / Ersan, Mahmut (Committee member) / Arizona State University (Publisher)
Created2021
Description
Global shortages of urea and unsustainable production of synthetic urea have caused concerns over the future of food production, automobile operation, and other processes. Urine is a waste product that could supplement synthetic urea production. This study utilizes polyamide reverse osmosis (RO) and nanofiltration (NF) membranes in a cross-flow orientation to selectively recover urea from fresh human urine. Urea permeation experiments were conducted to determine the effects of urea stabilization via pH adjustment and membrane type on the production of a pure urea product. Fouling mitigation experiments were then conducted to determine the efficacy of microfiltration (MF) pretreatment on the reduction of the membrane fouling layer. The results showed that the NF90 membrane had advantageous performance to the BW30 RO and NF270 membranes, permeating 76% of the urea while rejecting 68% of the conductivity. Urine stabilization via acetic acid or sodium hydroxide addition did not inhibit membrane performance, signifying the use of pH 5 as a suitable pretreatment condition. Real fresh urine had higher rejection of constituents for NF90, suggesting the reduction of flux across the membrane due to interactions with organic material. MF pretreatment reduced foulant thickness and permeate flux loss but did not change the speciation of microorganisms. Finally, different urea-based products, such as fertilizers, biocement, and synthetic polymers, were suggested to show the potential of urine-recovered urea to reduce costs. The results from this work show the efficacy of using polyamide RO and NF membranes to supplement unsustainable synthetic production of urea with sustainably sourced urea from a waste product, human urine.
ContributorsCrane, Lucas Christopher (Author) / Boyer, Treavor H (Thesis advisor) / Perreault, Francois (Committee member) / Westerhoff, Paul (Committee member) / Arizona State University (Publisher)
Created2022
Description
Nutrient rich agricultural runoff is a major source of phosphorus (P) and nitrogen (N) loading to surface waters, resulting in eutrophication and harmful algal blooms. The most effective nutrient removal technologies often have cost, land, or operational requirements that limits use in the decentralized areas that need it most. This dissertation investigated combined physical-chemical and microbiological technologies for combined P and N removal from nonpoint sources. Chapter 2 investigated the combination of basic oxygen furnace (BOF) steel slag and woody mulch for P removal by mineral precipitation and N removal by microbial denitrification. When combined with mulch in column experiments, slag with high fines content achieved complete P removal under unsaturated conditions. Batch experiments showed that microbial denitrification occurred under the highly alkaline conditions created by steel slag, but the timescale differential between P and N removal was a critical barrier to combining these treatment technologies. Chapter 3 evaluated a field-scale slag filter to treat agricultural tile drainage and lab-scale column experiments to provide insight on field conditions that impacted P removal. Increases in alkalinity had negative influences on P removal through inhibition of P mineral precipitation by BOF slag, while blast furnace (BF) steel slag was less impacted by alkalinity due to primarily adsorptive P removal. Regeneration strategies were identified based on water quality and slag type.Chapters 4 and 5 explored biological ion exchange (BIEX) as an option for addressing the timescale offset identified in Chapter 1. In Chapter 4 columns fed with dissolved organic matter (DOM) were not regenerated and over 50% DOM removal was observed, with the primary mechanism of removal identified as secondary ion exchange (SIEX)
between sulfate and DOM fractions with high affinities for ion exchange. Chapter 5 aimed to expand BIEX to N treatment through batch denitrification and adsorption experiments, which revealed a positive relationship between molecular weight of organic molecules and their ability to displace nitrate. This work shows that by having an improved understanding of impacted water characteristics, the information presented in this work can be used to select and implement effective treatment technologies for decentralized areas.
ContributorsEdgar, Michael Garrett (Author) / Boyer, Treavor H (Thesis advisor) / Hamdan, Nasser (Committee member) / Delgado, Anca (Committee member) / Arizona State University (Publisher)
Created2022
Description
Mineral weathering and industrial activities cause elevated concentration of hexavalent chromium (Cr(VI)) in groundwater, and this poses potential health concern (>10 ppb) to southwestern USA. The conversion of Cr(VI) to Cr(III) – a fairly soluble and non-toxic form at typical pH of groundwater is an effective method to control the mobility and carcinogenic effects of Cr(VI). In-situ chemical reduction using SnCl2 was investigated to initiate this redox process using jar testing with buffered ultrapure water and native Arizona groundwater spiked with varying Cr(VI) concentrations. Cr(VI) transformation by SnCl2 is super rapid (<60 seconds) and depends upon the molar dosage of Sn(II) to Cr(VI). Cr(VI) removal improved significantly at higher pH while was independent on Cr(VI) initial concentration and dissolved oxygen (DO) level. Co-existing oxyanions (As and W) competed with Cr(VI) for SnCl2 oxidation and adsorption sites of formed precipitates, thus resulted in lower Cr(VI) removal in the challenge water. SnCl2 reagent grade and commercial grade behaved similarly when freshly prepared, but the reducing strength of the commercial product decreased by 50% over a week after exposing to atmosphere. Equilibrium modeling with Visual MINTEQ suggested redox potential < 400 mV to reach Cr(VI) treatment goal of 10 ppb. Kinetics of Cr(VI) reduction was simulated via the rate expression: r=-k[H+]-0.25[Sn2+]0.5[Cr2O72-]3 with k = 0.146 uM-2.25s-1, which correlated consistently with experimental data under different pH and SnCl2 doses. These results proved SnCl2 reductive treatment is a simple and highly effective method to treat Cr(VI) in groundwater.
ContributorsNguyen, Duong Thanh (Author) / Westerhoff, Paul K (Thesis advisor) / Delgado, Anca G (Committee member) / Sinha, Shahnawaz (Committee member) / Arizona State University (Publisher)
Created2019
Description
The goal of this research was to study the effect of dilution on ammonium and potassium removal from real hydrolyzed urine. The performance of two natural zeolites, clinoptilolite and chabazite, was studied and compared with the help of batch equilibrium experiments at four dilution levels: 100%, 10%, 1% and 0.1% (urine volume/total solution volume). Further, the sorption behavior of other exchangeable ions (sodium, calcium and magnesium) in clinoptilolite and chabazite was studied to improve the understanding of ion exchange stoichiometry. Ammonium and potassium removal were highest at undiluted level in samples treated with clinoptilolite. This is a key finding as it illustrates the benefit of urine source separation. Chabazite treated samples showed highest ammonium and potassium removal at undiluted level at lower doses. At higher doses, potassium removal was similar in undiluted and 10% urine solutions whereas ammonium removal was the highest in 10% urine solutions. In general, chabazite showed higher ammonium and potassium removal than clinoptilolite. The result showed that ion exchange was stoichiometric in solutions with higher urine volumes.
ContributorsRegmi, Urusha (Author) / Boyer, Treavor H (Thesis advisor) / Delgado, Anca G (Committee member) / Hamilton, Kerry (Committee member) / Arizona State University (Publisher)
Created2019
Description
With the application of reverse osmosis (RO) membranes in the wastewater treatment and seawater desalination, the limitation of flux and fouling problems of RO have gained more attention from researchers. Because of the tunable structure and physicochemical properties of nanomaterials, it is a suitable material that can be used to incorporate with RO to change the membrane performances. Silver is biocidal, which has been used in a variety of consumer products. Recent studies showed that fabricating silver nanoparticles (AgNPs) on membrane surfaces can mitigate the biofouling problem on the membrane. Studies have shown that Ag released from the membrane in the form of either Ag ions or AgNP will accelerate the antimicrobial activity of the membrane. However, the silver release from the membrane will lower the silver loading on the membrane, which will eventually shorten the antimicrobial activity lifetime of the membrane. Therefore, the silver leaching amount is a crucial parameter that needs to be determined for every type of Ag composite membrane.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
ContributorsHan, Bingru (Author) / Westerhoff, Paul (Thesis advisor) / Perreault, Francois (Committee member) / Sinha, Shahnawaz (Committee member) / Arizona State University (Publisher)
Created2017
Description
Drinking water filtration using reverse osmosis (RO) membranes effectively removes salts and most other inorganic, organic, and microbial pollutants. RO technologies are utilized at both the municipal and residential scale. The formation of biofilms on RO membranes reduces water flux and increases energy consumption. The research conducted for this thesis involves In-Situ coating of silver, a known biocide, on the surface of RO membranes. This research was adapted from a protocol developed for coating flat sheet membranes with silver nanoparticles, and scaled up into spiral-wound membranes that are commonly used at the residential scale in point-of-use (POU) filtration systems. Performance analyses of the silver-coated spiral-wound were conducted in a mobile drinking water treatment system fitted with two POU units for comparison. Five month-long analyses were performed, including a deployment of the mobile system. In addition to flux, salt rejection, and other water quality analyses, additional membrane characterization tests were conducted on pristine and silver-coated membranes.
For flat sheet membranes coated with silver, the surface charge remained negative and contact angle remained below 90. Scaling up to spiral-wound RO membrane configuration was successful, with an average silver-loading of 1.93 g-Ag/cm2. Results showed the flux of water through the membrane ranged from 8 to 13 liters/m2*hr. (LMH) operating at 25% recovery during long-term of operation. The flux was initially decreased due to the silver coating, but no statistically significant differences were observed after 14 days of operation (P < 0.05). The salt rejection was also not effected due to the silver coating (P < 0.05). While 98% of silver was released during long-term studies, the silver release from the spiral-wound membrane was consistently below the secondary MCL of 100 ppb established by the EPA, and was consistently below 5 ppb after two hours of operation. Microbial assays in the form of heterotrophic plate counts suggested there was no statistically significant difference in the prevention of biofouling formation due to the silver coating (P < 0.05). In addition to performance tests and membrane characterizations, a remote data acquisition system was configured to remotely monitor performance and water quality parameters in the mobile system.
For flat sheet membranes coated with silver, the surface charge remained negative and contact angle remained below 90. Scaling up to spiral-wound RO membrane configuration was successful, with an average silver-loading of 1.93 g-Ag/cm2. Results showed the flux of water through the membrane ranged from 8 to 13 liters/m2*hr. (LMH) operating at 25% recovery during long-term of operation. The flux was initially decreased due to the silver coating, but no statistically significant differences were observed after 14 days of operation (P < 0.05). The salt rejection was also not effected due to the silver coating (P < 0.05). While 98% of silver was released during long-term studies, the silver release from the spiral-wound membrane was consistently below the secondary MCL of 100 ppb established by the EPA, and was consistently below 5 ppb after two hours of operation. Microbial assays in the form of heterotrophic plate counts suggested there was no statistically significant difference in the prevention of biofouling formation due to the silver coating (P < 0.05). In addition to performance tests and membrane characterizations, a remote data acquisition system was configured to remotely monitor performance and water quality parameters in the mobile system.
ContributorsZimmerman, Sean (Author) / Westerhoff, Paul K (Thesis advisor) / Sinha, Shahnawaz (Committee member) / Perreault, Francois (Committee member) / Arizona State University (Publisher)
Created2017