Matching Items (16)
Filtering by
- All Subjects: Electrical Engineering
Description
A proposed visible spectrum nanoscale imaging method requires material with permittivity values much larger than those available in real world materials to shrink the visible wavelength to attain the desired resolution. It has been proposed that the extraordinarily slow propagation experienced by light guided along plasmon resonant structures is a viable approach to obtaining these short wavelengths. To assess the feasibility of such a system, an effective medium model of a chain of Noble metal plasmonic nanospheres is developed, leading to a straightforward calculation of the waveguiding properties. Evaluation of other models for such structures that have appeared in the literature, including an eigenvalue problem nearest neighbor approximation, a multi- neighbor approximation with retardation, and a method-of-moments method for a finite chain, show conflicting expectations of such a structure. In particular, recent publications suggest the possibility of regions of invalidity for eigenvalue problem solutions that are considered far below the onset of guidance, and for solutions that assume the loss is low enough to justify perturbation approximations. Even the published method-of-moments approach suffers from an unjustified assumption in the original interpretation, leading to overly optimistic estimations of the attenuation of the plasmon guided wave. In this work it is shown that the method of moments approach solution was dominated by the radiation from the source dipole, and not the waveguiding behavior claimed. If this dipolar radiation is removed the remaining fields ought to contain the desired guided wave information. Using a Prony's-method-based algorithm the dispersion properties of the chain of spheres are assessed at two frequencies, and shown to be dramatically different from the optimistic expectations in much of the literature. A reliable alternative to these models is to replace the chain of spheres with an effective medium model, thus mapping the chain problem into the well-known problem of the dielectric rod. The solution of the Green function problem for excitation of the symmetric longitudinal mode (TM01) is performed by numerical integration. Using this method the frequency ranges over which the rod guides and the associated attenuation are clearly seen. The effective medium model readily allows for variation of the sphere size and separation, and can be taken to the limit where instead of a chain of spheres we have a solid Noble metal rod. This latter case turns out to be the optimal for minimizing the attenuation of the guided wave. Future work is proposed to simulate the chain of photonic nanospheres and the nanowire using finite-difference time-domain to verify observed guided behavior in the Green's function method devised in this thesis and to simulate the proposed nanosensing devices.
ContributorsHale, Paul (Author) / Diaz, Rodolfo E (Thesis advisor) / Goodnick, Stephen (Committee member) / Aberle, James T., 1961- (Committee member) / Palais, Joseph (Committee member) / Arizona State University (Publisher)
Created2013
Description
Multiport antennas offer greater design flexibility than traditional one-port designs. An antenna array is a special case of a multiport antenna. If the antenna's inter-element spacing is electrically small, the antenna is capable of achieving superdirectivity. Superdirective antenna arrays are known to be narrow band and have low radiation resistance which leads to low radiation efficiency and high VSWR. However, by increasing the self-impedance of the antenna elements, the radiation resistance is increased but the bandwidth remains narrow. A design methodology is developed using the ability to superimpose electric fields and multi-objective optimization to design antenna feed networks. While the emphasis in this dissertation is on antenna arrays and superdirectivity, the design methodology is general and can be applied to other multiport antennas. The design methodology is used to design a multiport impedance-matching network and optimize both the input impedance and radiation pattern of a two-port superdirective antenna array. It is shown that the multiport impedance-matching network is capable of improving the input impedance of the antenna array while maintaining high directionality. The antenna design is critical for the methodology to improve the bandwidth and radiation characteristics of the array. To double the bandwidth of the two-port impedance matched superdirective antenna array, a three-port Yagi-Uda antenna design is demonstrated. The addition of the extra antenna element does not increase the footprint of the antenna array. The design methodology is then used to design a symmetrical antenna array capable of steering its main beam in two directions.
ContributorsArceo, Diana (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T., 1961- (Committee member) / Moeller, Karl (Committee member) / Palais, Joseph (Committee member) / Arizona State University (Publisher)
Created2012
Description
Reconfigurable metasurfaces (RMSs) are promising solutions for beamforming and sensing applications including 5G and beyond wireless communications, satellite and radar systems, and biomarker sensing. In this work, three distinct RMS architectures – reconfigurable intelligent surfaces (RISs), meta-transmission lines (meta-TLs), and substrate integrated waveguide leaky-wave antennas (SIW-LWAs) are developed and characterized. The ever-increasing demand for higher data rates and lower latencies has propelled the telecommunications industry to adopt higher frequencies for 5G and beyond wireless communications. However, this transition to higher frequencies introduces challenges in terms of signal coverage and path loss. Many base stations would be necessary to ensure signal fidelity in such a setting, making bulky phased array-based solutions impractical. Consequently, to meet the unique needs of 5G and beyond wireless communication networks, this work proposes the use of RISs characterized by low-profile, low-RF losses, low-power consumption, and high-gain capabilities, making them excellent candidates for future wireless communication applications. Specifically, RISs at sub-6GHz, mmWave and sub-THz frequencies are analyzed to demonstrate their ability to improve signal strength and coverage.
Further, a linear meta-TL wave space is designed to achieve miniaturization of true-time delay beamforming structures such as Rotman lenses which are traditionally bulky. To address this challenge, a modified lumped element TL model is proposed. A meta-TL is created by including the mutual coupling effects and can be used to slow down the electromagnetic signal and realize miniaturized lenses. A proof-of-concept 1D meta-TL is developed to demonstrate about 90% size reduction and 40% bandwidth improvement.
Furthermore, a conformable antenna design for radio frequency-based tracking of hand gestures is also detailed. SIW-LWA is employed as the radiating element to couple RF signals into the human hand. The antenna is envisaged to be integrated in a wristband topology and capture the changes in the electric field caused by various movements of the hand. The scattering parameters are used to track the changes in the wrist anatomy. Sensor characterization showed significant sensitivity suppression due to lossy multi-dielectric nature tissues in the wrist. However, the sensor demonstrates good coupling of electromagnetic energy making it suitable for on-body wireless communications and magnetic resonance imaging applications.
ContributorsKashyap, Bharath Gundappa (Author) / Trichopoulos, Georgios C (Thesis advisor) / Balanis, Constantine A (Committee member) / Aberle, James T (Committee member) / Alkhateeb, Ahmed (Committee member) / Imani, Seyedmohammedreza F (Committee member) / Arizona State University (Publisher)
Created2023
Description
The reconfigurable intelligent surface (RIS) shown in this work is a programmable metasurface integrated with a dedicated microcontroller that redirects an impinging signal to the desired direction. Its characteristic allows the RIS to act as a mirror for microwave signals. Unlike a perfect electric conductor (PEC), the RIS has much more flexibility in redirecting signals. This work involves the measurement of a passive, fixed beam, 25x32 element mmWave RIS that operates at 28.5 GHz. Bistatic and monostatic measurement setups are both used to find the radar cross section (RCS) of the RIS. The process of creating the measurement setups and the final measurement results is discussed. The measurement setup is further characterized using the High-Frequency Structure Simulator (HFSS) software and the final measurement results are compared to analytical solutions computed using MATLAB. The first prototype of the RIS has a loss of 8.4 dB when compared to a PEC and is physically curved. There is also a side lobe at the boresight of the RIS board that is only 8 dB less than the main beam in best-case scenario. This curvature causes issues with the monostatic measurement because it changes the phase that arrives at the RIS. The second prototype of the RIS has only 5.84 dB of loss compared to PEC. This measurement setup behaves mostly as expected when comparing the measurement results to the analytical solutions and given the limitations of the setup. A collimating lens was used as a part of the setup which reflects part of the incoming signal. The edge of the lens also causes diffraction. These factors contribute to multipath interference arriving at the receive antenna and increases measurement error. The lens also creates unequal amplitude illumination across the surface of the RIS which changes the RCS pattern. Using the lens allows a more space-efficient setup while still obtaining relatively constant phase illuminating across the RIS board.
ContributorsTjahjadi, Brian (Author) / Trichopoulos, Georgios C (Thesis advisor) / Aberle, James T (Committee member) / Imani, Seyedmohammadreza F (Committee member) / Arizona State University (Publisher)
Created2022
Description
Nanophotonics studies the interaction of light with nanoscale devices and nanostructures. This thesis focuses on developing nanoscale devices for optical modulation (saturable absorber and all-optical modulator) and investigating light scattering from nanoparticles for underwater navigation and energy sector application. Saturable absorbers and all-optical modulators are essential to generate ultrashort high-power laser pulses and high-speed communications. Graphene-based devices are broadband, ultrafast, and compatible with different substrates and fibers. Nevertheless, the required fluence to saturate or modulate the optical signal with graphene is still high to realize low-threshold, compact broadband devices, which are essential for many applications. This dissertation emphasizes that the strong light-matter interaction in graphene-plasmonic hybrid metasurface greatly enhances monolayer graphene’s saturable absorption and optical signal modulation effect while maintaining graphene’s ultrafast carrier dynamics. Furthermore, based on this concept, simulation models and experimental demonstrations are presented in this dissertation to demonstrate both subwavelength (~λ/5 in near-infrared and ~λ/10 in mid-infrared) thick graphene-based saturable absorber (with record-low saturation fluence (~0.1μJ/cm2), and ultrashort recovery time (~60fs) at near-infrared wavelengths) and all-optical modulators ( with 40% reflection modulation at 6.5μm with ~55μJ/cm2 pump fluence and ultrafast relaxation time of ~1ps at 1.56μm with less than 8μJ/cm2 pump fluence).
Underwater navigation is essential for various underwater vehicles. However, there is no reliable method for underwater navigation. This dissertation presents a numerical simulation model and algorithm for navigation based on underwater polarization mapping data. With the methods developed, for clear water in the swimming pool, it is possible to achieve a sun position error of 0.35˚ azimuth and 0.03˚ zenith angle, and the corresponding location prediction error is ~23Km. For turbid lake water, a location determination error of ~100Km is achieved. Furthermore, maintenance of heliostat mirrors and receiver tubes is essential for properly operating concentrated solar power (CSP) plants. This dissertation demonstrates a fast and field deployable inspection method to measure the heliostat mirror soiling levels and receiver tube defect detection based on polarization images. Under sunny and clear sky conditions, accurate reflection efficiency (error ~1%) measurement for mirrors with different soiling levels is achieved, and detection of receiver tube defects is demonstrated.
ContributorsRafique, Md Zubair Ebne (Author) / Yao, Yu (Thesis advisor) / Palais, Joseph (Committee member) / Zhang, Yong-Hang (Committee member) / Sukharev, Maxim (Committee member) / Arizona State University (Publisher)
Created2022
Description
This dissertation consists of four parts: design of antenna in lossy media, analysisof wire antennas using electric field integral equation (EFIE) and wavelets, modeling and measurement of grounded waveguide coplanar waveguide (GCPW) for automotive radar, and E-Band 3-D printed antenna and measurement using VNA. In the first part, the antenna is modeled and simulated in lossy media. First, the vector wave functions is solved in the fundamental mode. Next the energy flow velocity is plotted to show near-field energy distribution for both TM and TE in air and seawater environment. Finally the power relation in seawater is derived to calculate the source dipole moment and required power.
In the second part, the current distribution on the antenna is derived by solving EFIE with moment of methods (MoM). Both triangle and Coifman wavelet (Coiflet) are used as basis and weight functions. Then Input impedance of the antenna is computed and results are compared with traditional sinusoid current distribution assumption. Finally the input impedance of designed antenna is computed and matching network is designed and show resonant at designed frequency.
In the third part, GCPW is modeled and measured in E-band. Laboratory measurements are conducted in 75 to 84 GHz. The original system is embedded with error boxes due to misalignment and needed to be de-embedded. Then the measurement data is processed and the results is compared with raw data.
In the fourth part, the horn antennas and slotted waveguide array antenna (SWA) are designed for automotive radar in 75GHz to 78GHz. The horn antennas are fabricated using 3D printing of ABS material, and electro-plating with copper. The analytic solution and HFSS simulation show good agreement with measurement.
ContributorsZhou, Sai (Author) / Pan, George (Thesis advisor) / Aberle, James (Committee member) / Palais, Joseph (Committee member) / Allee, David (Committee member) / Arizona State University (Publisher)
Created2021
Description
Antenna arrays are widely used in wireless communication, radar, remote sensing, and other fields. Compared to traditional linear antenna arrays, novel nonlinear antenna arrays have fascinating advantages in terms of structural simplicity, lower cost, wider bandwidth, faster scanning speed, and lower side-lobe levels. This dissertation explores a novel design of a phased array antenna with an augmented scanning range, aiming to establish a clear connection between mathematical principles and practical circuitry. To achieve this goal, the Van der Pol (VDP) model is applied to a single-transistor oscillator to obtain the isolated limit cycle. The coupled oscillators are then integrated into a 1 times 7 coupled phased array, using the Keysight PathWave Advanced Design System (ADS) for tuning and optimization. The VDP model is used for analytic study of bifurcation, quasi-sinusoidal oscillation, quasi-periodic chaos, and oscillator death, while ADS schematics guide engineering implementation and physical fabrication. The coupled oscillators drive cavity-backed antennas, forming a one-dimensional scanning antenna array of 1 times 7. The approaches for increasing the scanning range performance are discussed.
ContributorsZhang, Kaiyue (Author) / Pan, George (Thesis advisor) / Yu, Hongbin (Committee member) / Aberle, James (Committee member) / Palais, Joseph (Committee member) / Arizona State University (Publisher)
Created2023
Description
Polarization imaging and polarization microscopy is of great interest in industrial inspection, defense, biomedical and clinical research, food safety, etc. An ideal polarization imaging system suitable for versatile applications should be full-Stokes, compact, broadband, fast, and highly accurate within a large operation angle. However, such a polarization imaging system remains elusive among state-of-the-art technology. Recently, flat optics based on metasurfaces have been explored for polarization detection and imaging. Compared with state-of-art, metasurface-based solutions have the advantages of compactness, great design flexibility, and feasibility for on-chip integration. This dissertation reports a dual wavelength (630 to 670nm and 480nm to 520nm) chiral metasurfaces featured with sub-wavelength dimension, extinction ratio over 10 across a broad operation bandwidth (175nm) and efficiency over 60%, which can be used for detection and generation of circular polarization (Chapter 2).
This dissertation then reports a chip-integrated full-Stokes polarimetric Complementary metal–oxide–semiconductor (CMOS) imaging sensor based on metasurface polarization filter arrays (MPFA) mentioned above. The sensor has high measurement accuracy of polarization states with an angle of view up to 40°. Calibration and characterization of the device are demonstrated, whereby high polarization states measurement accuracy (measurement error <4%) at incidence angle up to ±20° and full Stokes polarization images of polarized objects are shown. (Chapter 3).
A scalable fabrication approach based on nano imprint lithography is demonstrated, with improved fabrication efficiency, lower cost, and higher optical performance up to 10 times compared to EBL process. (Chapter 4).
Several polarization imaging applications including a dual-camera full-Stokes underwater polarization navigation system are discussed. Polarization mapping under clear sky and clear water is demonstrated for proof concept. Enhancing contrast of objects through turbid water and polarization images of silver dendrites are also discussed (Chapter 5).
Though distinctive in its advantages in rich polarization information, most existing Mueller matrix microscope (MMM) operate at single mode, narrow bandwidth with bulky components. This dissertation reports a compact, dual wavelength, dual mode MMM with satisfactory measurement accuracy (Mueller matrix (MM) measurement error≤ 2.1%) using polarimetric imaging sensor mentioned previously, MM imaging of photonic structures, bio-tissues, etc are demonstrated for proof of concept (Chapter 6).
ContributorsZuo, Jiawei (Author) / Yao, Yu (Thesis advisor) / Wang, Chao (Thesis advisor) / Palais, Joseph (Committee member) / Sinha, Kanupriya (Committee member) / Arizona State University (Publisher)
Created2023
Description
The micromotions (e.g. vibration, rotation, etc.,) of a target induce time-varying frequency modulations on the reflected signal, called the micro-Doppler modulations. Micro-Doppler modulations are target specific and may contain information needed to detect and characterize the target. Thus, unlike conventional Doppler radars, Fourier transform cannot be used for the analysis of these time dependent frequency modulations. While Doppler radars can detect the presence of a target and deduce if it is approaching or receding from the radar location, they cannot identify the target. Meaning, for a Doppler radar, a small commercial aircraft and a fighter plane when gliding at the same velocity exhibit similar radar signature. However, using a micro-Doppler radar, the time dependent frequency variations caused by the vibrational and rotational micromotions of the two aircrafts can be captured and analyzed to discern between them. Similarly, micro-Doppler signature can be used to distinguish a multicopter from a bird, a quadcopter from a hexacopter or a octacopter, a bus from a car or a truck and even one person from another. In all these scenarios, joint time-frequency transforms must be employed for the analysis of micro-Doppler variations, in order to extract the targets’ features.
Due to ample bandwidth, THz radiation provides richer radar signals than the microwave systems. Thus, a Terahertz (THz) micro-Doppler radar is developed in this work for the detection and characterization of the micro-Doppler signatures of quadcopters. The radar is implemented as a continuous-wave (CW) radar in monostatic configuration and operates at a low-THz frequency of 270 GHz. A linear time-frequency transform, the short-time Fourier transform (STFT) is used for the analysis the micro-Doppler signature. The designed radar has been built and measurements are carried out using a quadcopter to detect the micro-Doppler modulations caused by the rotation of its propellers. The spectrograms are obtained for a quadcopter hovering in front of the radar and analysis methods are developed for characterizing the frequency variations caused by the rotational and vibrational micromotions of the quadcopter. The proposed method can be effective for distinguishing the quadcopters from other flying targets like birds which lack the rotational micromotions.
Due to ample bandwidth, THz radiation provides richer radar signals than the microwave systems. Thus, a Terahertz (THz) micro-Doppler radar is developed in this work for the detection and characterization of the micro-Doppler signatures of quadcopters. The radar is implemented as a continuous-wave (CW) radar in monostatic configuration and operates at a low-THz frequency of 270 GHz. A linear time-frequency transform, the short-time Fourier transform (STFT) is used for the analysis the micro-Doppler signature. The designed radar has been built and measurements are carried out using a quadcopter to detect the micro-Doppler modulations caused by the rotation of its propellers. The spectrograms are obtained for a quadcopter hovering in front of the radar and analysis methods are developed for characterizing the frequency variations caused by the rotational and vibrational micromotions of the quadcopter. The proposed method can be effective for distinguishing the quadcopters from other flying targets like birds which lack the rotational micromotions.
ContributorsKashyap, Bharath Gundappa (Author) / Trichopoulos, Georgios C (Thesis advisor) / Balanis, Constantine A (Committee member) / Aberle, James T (Committee member) / Arizona State University (Publisher)
Created2018
Description
Nanowires are one-dimensional (1D) structures with diameter on the nanometer scales with a high length-to-diameter aspect ratio. Nanowires of various materials including semiconductors, dielectrics and metals have been intensively researched in the past two decades for applications to electrical and optical devices. Typically, nanowires are synthesized using the vapor-liquid-solid (VLS) approach, which allows defect-free 1D growth despite the lattice mismatch between nanowires and substrates. Lattice mismatch issue is a serious problem in high-quality thin film growth of many semiconductors and non-semiconductors. Therefore, nanowires provide promising platforms for the applications requiring high crystal quality materials.
With the 1D geometry, nanowires are natural optical waveguides for light guiding and propagation. By introducing feedback mechanisms to nanowire waveguides, such as the cleaved end facets, the nanowires can work as ultra-small size lasers. Since the first demonstration of the room-temperature ultraviolet nanowire lasers in 2001, the nanowire lasers covering from ultraviolet to mid infrared wavelength ranges have been intensively studied. This dissertation focuses on the optical characterization and laser fabrication of two nanowire materials: erbium chloride silicate nanowires and composition-graded CdSSe semiconductor alloy nanowires.
Chapter 1 – 5 of this dissertation presents a comprehensive characterization of a newly developed erbium compound material, erbium chloride silicate (ECS) in a nanowire form. Extensive experiments demonstrated the high crystal quality and excellent optical properties of ECS nanowires. Optical gain higher than 30 dB/cm at 1.53 μm wavelength is demonstrated on single ECS nanowires, which is higher than the gain of any reported erbium materials. An ultra-high Q photonic crystal micro-cavity is designed on a single ECS nanowire towards the ultra-compact lasers at communication wavelengths. Such ECS nanowire lasers show the potential applications of on-chip photonics integration.
Chapter 6 – 7 presents the design and demonstration of dynamical color-controllable lasers on a single CdSSe alloy nanowire. Through the defect-free VLS growth, engineering of the alloy composition in a single nanowire is achieved. The alloy composition of CdSxSe1-x uniformly varies along the nanowire axis from x=1 to x=0, giving the opportunity of multi-color lasing in a monolithic structure. By looping the wide-bandgap end of the alloy nanowire through nanoscale manipulation, the simultaneous two-color lasing at green and red colors are demonstrated. The 107 nm wavelength separation of the two lasing colors is much larger than the gain bandwidth of typical semiconductors. Since the two-color lasing shares the output port, the color of the total lasing output can be controlled dynamically between the two fundamental colors by changing the relative output power of two lasing colors. Such multi-color lasing and continuous color tuning in a wide spectral range would eventually enable color-by-design lasers to be used for lighting, display and many other applications.
With the 1D geometry, nanowires are natural optical waveguides for light guiding and propagation. By introducing feedback mechanisms to nanowire waveguides, such as the cleaved end facets, the nanowires can work as ultra-small size lasers. Since the first demonstration of the room-temperature ultraviolet nanowire lasers in 2001, the nanowire lasers covering from ultraviolet to mid infrared wavelength ranges have been intensively studied. This dissertation focuses on the optical characterization and laser fabrication of two nanowire materials: erbium chloride silicate nanowires and composition-graded CdSSe semiconductor alloy nanowires.
Chapter 1 – 5 of this dissertation presents a comprehensive characterization of a newly developed erbium compound material, erbium chloride silicate (ECS) in a nanowire form. Extensive experiments demonstrated the high crystal quality and excellent optical properties of ECS nanowires. Optical gain higher than 30 dB/cm at 1.53 μm wavelength is demonstrated on single ECS nanowires, which is higher than the gain of any reported erbium materials. An ultra-high Q photonic crystal micro-cavity is designed on a single ECS nanowire towards the ultra-compact lasers at communication wavelengths. Such ECS nanowire lasers show the potential applications of on-chip photonics integration.
Chapter 6 – 7 presents the design and demonstration of dynamical color-controllable lasers on a single CdSSe alloy nanowire. Through the defect-free VLS growth, engineering of the alloy composition in a single nanowire is achieved. The alloy composition of CdSxSe1-x uniformly varies along the nanowire axis from x=1 to x=0, giving the opportunity of multi-color lasing in a monolithic structure. By looping the wide-bandgap end of the alloy nanowire through nanoscale manipulation, the simultaneous two-color lasing at green and red colors are demonstrated. The 107 nm wavelength separation of the two lasing colors is much larger than the gain bandwidth of typical semiconductors. Since the two-color lasing shares the output port, the color of the total lasing output can be controlled dynamically between the two fundamental colors by changing the relative output power of two lasing colors. Such multi-color lasing and continuous color tuning in a wide spectral range would eventually enable color-by-design lasers to be used for lighting, display and many other applications.
ContributorsLiu, Zhicheng (Author) / Ning, Cun-Zheng (Thesis advisor) / Palais, Joseph (Committee member) / Yu, Hongbin (Committee member) / Yao, Yu (Committee member) / Arizona State University (Publisher)
Created2015