Matching Items (78)
Description
A single solar cell provides close to 0.5 V output at its maximum power point, which is very
low for any electronic circuit to operate. To get rid of this problem, traditionally multiple
solar cells are connected in series to get higher voltage. The disadvantage of this approach
is the efficiency loss for partial shading or mismatch. Even as low as 6-7% of shading can
result in more than 90% power loss. Therefore, Maximum Power Point Tracking (MPPT)
at single solar cell level is the most efficient way to extract power from solar cell.
Power Management IC (MPIC) used to extract power from single solar cell, needs to
start at 0.3 V input. MPPT circuitry should be implemented with minimal power and area
overhead. To start the PMIC at 0.3 V, a switch capacitor charge pump is utilized as an
auxiliary start up circuit for generating a regulated 1.8 V auxiliary supply from 0.3 V input.
The auxiliary supply powers up a MPPT converter followed by a regulated converter. At
the start up both the converters operate at 100 kHz clock with 80% duty cycle and system
output voltage starts rising. When the system output crosses 2.7 V, the auxiliary start up
circuit is turned off and the supply voltage for both the converters is derived from the system
output itself. In steady-state condition the system output is regulated to 3.0 V.
A fully integrated analog MPPT technique is proposed to extract maximum power from
the solar cell. This technique does not require Analog to Digital Converter (ADC) and
Digital Signal Processor (DSP), thus reduces area and power overhead. The proposed
MPPT techniques includes a switch capacitor based power sensor which senses current of
boost converter without using any sense resistor. A complete system is designed which
starts from 0.3 V solar cell voltage and provides regulated 3.0 V system output.
low for any electronic circuit to operate. To get rid of this problem, traditionally multiple
solar cells are connected in series to get higher voltage. The disadvantage of this approach
is the efficiency loss for partial shading or mismatch. Even as low as 6-7% of shading can
result in more than 90% power loss. Therefore, Maximum Power Point Tracking (MPPT)
at single solar cell level is the most efficient way to extract power from solar cell.
Power Management IC (MPIC) used to extract power from single solar cell, needs to
start at 0.3 V input. MPPT circuitry should be implemented with minimal power and area
overhead. To start the PMIC at 0.3 V, a switch capacitor charge pump is utilized as an
auxiliary start up circuit for generating a regulated 1.8 V auxiliary supply from 0.3 V input.
The auxiliary supply powers up a MPPT converter followed by a regulated converter. At
the start up both the converters operate at 100 kHz clock with 80% duty cycle and system
output voltage starts rising. When the system output crosses 2.7 V, the auxiliary start up
circuit is turned off and the supply voltage for both the converters is derived from the system
output itself. In steady-state condition the system output is regulated to 3.0 V.
A fully integrated analog MPPT technique is proposed to extract maximum power from
the solar cell. This technique does not require Analog to Digital Converter (ADC) and
Digital Signal Processor (DSP), thus reduces area and power overhead. The proposed
MPPT techniques includes a switch capacitor based power sensor which senses current of
boost converter without using any sense resistor. A complete system is designed which
starts from 0.3 V solar cell voltage and provides regulated 3.0 V system output.
ContributorsSingh, Shrikant (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2015
Description
Traditional wireless communication systems operate in duplexed modes i.e. using time division duplexing or frequency division duplexing. These methods can respectively emulate full duplex mode operation or realize full duplex mode operation with decreased spectral efficiency. This thesis presents a novel method of achieving full duplex operation by actively cancelling out the transmitted signal in pseudo-real time. With appropriate hardware, the algorithms and techniques used in this work can be implemented in real time without any knowledge of the channel or any training sequence. Convergence times of down to 1 ms can be achieved which is adequate for the coherence bandwidths associated with an indoor environment. By utilizing adaptive cancellation, additional overhead for re-calibrating the system in other open-loop methods is not needed.
ContributorsAvasarala, Sanjay (Author) / Kiaei, Sayfe (Thesis advisor) / Kitchen, Jennifer (Committee member) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2016
Description
Since the inception of Internet of Things (IoT) framework, the amount of interaction between electronic devices has tremendously increased and the ease of implementing software between such devices has bettered. Such data exchange between devices, whether between Node to Server or Node to Node, has paved way for creating new business models. Wireless Video Sensor Network Platforms are being used to monitor and understand the surroundings better. Both hardware and software supporting such devices have become much smaller and yet stronger to enable these. Specifically, the invention of better software that enable Wireless data transfer have become more simpler and lightweight technologies such as HTML5 for video rendering, Common Gateway Interface(CGI) scripts enabling interactions between client and server and WebRTC from Google for peer to peer interactions. The role of web browsers in enabling these has been vastly increasing.
Although HTTP is the most reliable and consistent data transfer protocol for such interactions, the most important underlying challenge with such platforms is the performance based on power consumption and latency in data transfer.
In the scope of this thesis, two applications using CGI and WebRTC for data transfer over HTTP will be presented and the power consumption by the peripherals in transmitting the data and the possible implications for those will be discussed.
Although HTTP is the most reliable and consistent data transfer protocol for such interactions, the most important underlying challenge with such platforms is the performance based on power consumption and latency in data transfer.
In the scope of this thesis, two applications using CGI and WebRTC for data transfer over HTTP will be presented and the power consumption by the peripherals in transmitting the data and the possible implications for those will be discussed.
ContributorsRentala, Sri Harsha (Author) / Reisslein, Martin (Thesis advisor) / Kitchen, Jennifer (Committee member) / McGarry, Michael (Committee member) / Arizona State University (Publisher)
Created2016
Description
In this work, a 12-bit ADC with three types of calibration is proposed for high speed security applications as well as a precision application. This converter performs for both applications because it satisfies all the necessary specifications such as minimal device mismatch and offset, programmability to decrease aging effects, high SNR for increased ENOB and fast conversion rate. The designed converter implements three types of calibration necessary for offset and gain error, including: a correlated double sampling integrator used in the first stage of the ADC, a power up auto zero technique implemented in the digital code to store any offset and subtract out if necessary, and an automatic startup and manual calibration to control the common mode voltages. The proposed ADC was designed in Intel’s 10nm technology. This ADC is designed to monitor DC voltages for the precision and high speed applications. The conversion rate of the analog to digital converter is programmable to 7µs or 910ns, depending on the precision or high speed application, respectively. The range of the input and reference supply is 0 to 1.25V. The ADC is designed in Intel 10nm technology using a 1.8V supply consuming an area of 0.0705mm2. This thesis explores challenges of designing a dual-purpose analog to digital converter, which include: 1.) increased offset in 10nm technology, 2.) dual application ADC that can be accurate and fast, 3.) reducing the parasitic capacitance of the ADC, and 4.) gain error that occurs in ADCs.
ContributorsSchmelter, Brooke (Author) / Bakkaloglu, Bertan (Thesis advisor) / Ogras, Umit Y. (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017
Description
As wireless communication enters smartphone era, more complicated communication technologies are being used to transmit higher data rate. Power amplifier (PA) has to work in back-off region, while this inevitably reduces battery life for cellphones. Various techniques have been reported to increase PA efficiency, such as envelope elimination and restoration (EER) and envelope tracking (ET). However, state of the art ET supply modulators failed to address high efficiency, high slew rate, and accurate tracking concurrently.
In this dissertation, a linear-switch mode hybrid ET supply modulator utilizing adaptive biasing and gain enhanced current mirror operational transconductance amplifier (OTA) with class-AB output stage in parallel with a switching regulator is presented. In comparison to a conventional OTA design with similar quiescent current consumption, proposed approach improves positive and negative slew rate from 50 V/µs to 93.4 V/µs and -87 V/µs to -152.5 V/µs respectively, dc gain from 45 dB to 67 dB while consuming same amount of quiescent current. The proposed hybrid supply modulator achieves 83% peak efficiency, power added efficiency (PAE) of 42.3% at 26.2 dBm for a 10 MHz 7.24 dB peak-to-average power ratio (PAPR) LTE signal and improves PAE by 8% at 6 dB back off from 26.2 dBm power amplifier (PA) output power with respect to fixed supply. With a 10 MHz 7.24 dB PAPR QPSK LTE signal the ET PA system achieves adjacent channel leakage ratio (ACLR) of -37.7 dBc and error vector magnitude (EVM) of 4.5% at 26.2 dBm PA output power, while with a 10 MHz 8.15 dB PAPR 64QAM LTE signal the ET PA system achieves ACLR of -35.6 dBc and EVM of 6% at 26 dBm PA output power without digital pre-distortion (DPD). The proposed supply modulator core circuit occupies 1.1 mm2 die area, and is fabricated in a 0.18 µm CMOS technology.
In this dissertation, a linear-switch mode hybrid ET supply modulator utilizing adaptive biasing and gain enhanced current mirror operational transconductance amplifier (OTA) with class-AB output stage in parallel with a switching regulator is presented. In comparison to a conventional OTA design with similar quiescent current consumption, proposed approach improves positive and negative slew rate from 50 V/µs to 93.4 V/µs and -87 V/µs to -152.5 V/µs respectively, dc gain from 45 dB to 67 dB while consuming same amount of quiescent current. The proposed hybrid supply modulator achieves 83% peak efficiency, power added efficiency (PAE) of 42.3% at 26.2 dBm for a 10 MHz 7.24 dB peak-to-average power ratio (PAPR) LTE signal and improves PAE by 8% at 6 dB back off from 26.2 dBm power amplifier (PA) output power with respect to fixed supply. With a 10 MHz 7.24 dB PAPR QPSK LTE signal the ET PA system achieves adjacent channel leakage ratio (ACLR) of -37.7 dBc and error vector magnitude (EVM) of 4.5% at 26.2 dBm PA output power, while with a 10 MHz 8.15 dB PAPR 64QAM LTE signal the ET PA system achieves ACLR of -35.6 dBc and EVM of 6% at 26 dBm PA output power without digital pre-distortion (DPD). The proposed supply modulator core circuit occupies 1.1 mm2 die area, and is fabricated in a 0.18 µm CMOS technology.
ContributorsJing, Yue (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kiaei, Sayfe (Committee member) / Kitchen, Jennifer (Committee member) / Song, Hongjiang (Committee member) / Arizona State University (Publisher)
Created2017
Description
A Multi-input single inductor dual-output Boost based architecture for Multi-junction PV energy harvesting source is presented. The system works in Discontinuous Conduction Mode to achieve the independent input regulation for multi-junction PV source. A dual-output path is implemented to regulate the output at 3V as well as store the extra energy at light load condition. The dual-loop based sliding-mode MPPT for multi-junction PV is proposed to speed up the system response time for prompt irradiation change as well as maximize MPPT efficiency. The whole system achieves peak efficiency of 83% and MPPT efficiency of 95%. The whole system is designed, simulated in Cadence and implemented in PCB platform.
ContributorsGeng, Yu (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017
Description
Time-interleaved analog to digital converters (ADCs) have become critical components in high-speed communication systems. Consumers demands for smaller size, more bandwidth and more features from their communication systems have driven the market to use modern complementary metal-oxide-semiconductor (CMOS) technologies with shorter channel-length transistors and hence a more compact design. Downscaling the supply voltage which is required in submicron technologies benefits digital circuits in terms of power and area. Designing accurate analog circuits, however becomes more challenging due to the less headroom. One way to overcome this problem is to use calibration to compensate for the loss of accuracy in analog circuits.
Time-interleaving increases the effective data conversion rate in ADCs while keeping the circuit requirements the same. However, this technique needs special considerations as other design issues associated with using parallel identical channels emerge. The first and the most important is the practical issue of timing mismatch between channels, also called sample-time error, which can directly affect the performance of the ADC. Many techniques have been developed to tackle this issue both in analog and digital domains. Most of these techniques have high complexities especially when the number of channels exceeds 2 and some of them are only valid when input signal is a single tone sinusoidal which limits the application.
This dissertation proposes a sample-time error calibration technique which bests the previous techniques in terms of simplicity, and also could be used with arbitrary input signals. A 12-bit 650 MSPS pipeline ADC with 1.5 GHz analog bandwidth for digital beam forming systems is designed in IBM 8HP BiCMOS 130 nm technology. A front-end sample-and-hold amplifier (SHA) was also designed to compare with an SHA-less design in terms of performance, power and area. Simulation results show that the proposed technique is able to improve the SNDR by 20 dB for a mismatch of 50% of the sampling period and up to 29 dB at 37% of the Nyquist frequency. The designed ADC consumes 122 mW in each channel and the clock generation circuit consumes 142 mW. The ADC achieves 68.4 dB SNDR for an input of 61 MHz.
Time-interleaving increases the effective data conversion rate in ADCs while keeping the circuit requirements the same. However, this technique needs special considerations as other design issues associated with using parallel identical channels emerge. The first and the most important is the practical issue of timing mismatch between channels, also called sample-time error, which can directly affect the performance of the ADC. Many techniques have been developed to tackle this issue both in analog and digital domains. Most of these techniques have high complexities especially when the number of channels exceeds 2 and some of them are only valid when input signal is a single tone sinusoidal which limits the application.
This dissertation proposes a sample-time error calibration technique which bests the previous techniques in terms of simplicity, and also could be used with arbitrary input signals. A 12-bit 650 MSPS pipeline ADC with 1.5 GHz analog bandwidth for digital beam forming systems is designed in IBM 8HP BiCMOS 130 nm technology. A front-end sample-and-hold amplifier (SHA) was also designed to compare with an SHA-less design in terms of performance, power and area. Simulation results show that the proposed technique is able to improve the SNDR by 20 dB for a mismatch of 50% of the sampling period and up to 29 dB at 37% of the Nyquist frequency. The designed ADC consumes 122 mW in each channel and the clock generation circuit consumes 142 mW. The ADC achieves 68.4 dB SNDR for an input of 61 MHz.
ContributorsNazari, Ali (Author) / Barnaby, Hugh James (Thesis advisor) / Jalali-Farahani, Bahar (Committee member) / Bakkaloglu, Bertan (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2017
Description
Video capture, storage, and distribution in wireless video sensor networks
(WVSNs) critically depends on the resources of the nodes forming the sensor
networks. In the era of big data, Internet of Things (IoT), and distributed
demand and solutions, there is a need for multi-dimensional data to be part of
the Sensor Network data that is easily accessible and consumable by humanity as
well as machinery. Images and video are expected to become as ubiquitous as is
the scalar data in traditional sensor networks. The inception of video-streaming
over the Internet, heralded a relentless research for effective ways of
distributing video in a scalable and cost effective way. There has been novel
implementation attempts across several network layers. Due to the inherent
complications of backward compatibility and need for standardization across
network layers, there has been a refocused attention to address most of the
video distribution over the application layer. As a result, a few video
streaming solutions over the Hypertext Transfer Protocol (HTTP) have been
proposed. Most notable are Apple’s HTTP Live Streaming (HLS) and the Motion
Picture Experts Groups Dynamic Adaptive Streaming over HTTP (MPEG-DASH). These
frameworks, do not address the typical and future WVSN use cases. A highly
flexible Wireless Video Sensor Network Platform and compatible DASH (WVSNP-DASH)
are introduced. The platform's goal is to usher video as a data element that
can be integrated into traditional and non-Internet networks. A low cost,
scalable node is built from the ground up to be fully compatible with the
Internet of Things Machine to Machine (M2M) concept, as well as the ability to
be easily re-targeted to new applications in a short time. Flexi-WVSNP design
includes a multi-radio node, a middle-ware for sensor operation and
communication, a cross platform client facing data retriever/player framework,
scalable security as well as a cohesive but decoupled hardware and software
design.
(WVSNs) critically depends on the resources of the nodes forming the sensor
networks. In the era of big data, Internet of Things (IoT), and distributed
demand and solutions, there is a need for multi-dimensional data to be part of
the Sensor Network data that is easily accessible and consumable by humanity as
well as machinery. Images and video are expected to become as ubiquitous as is
the scalar data in traditional sensor networks. The inception of video-streaming
over the Internet, heralded a relentless research for effective ways of
distributing video in a scalable and cost effective way. There has been novel
implementation attempts across several network layers. Due to the inherent
complications of backward compatibility and need for standardization across
network layers, there has been a refocused attention to address most of the
video distribution over the application layer. As a result, a few video
streaming solutions over the Hypertext Transfer Protocol (HTTP) have been
proposed. Most notable are Apple’s HTTP Live Streaming (HLS) and the Motion
Picture Experts Groups Dynamic Adaptive Streaming over HTTP (MPEG-DASH). These
frameworks, do not address the typical and future WVSN use cases. A highly
flexible Wireless Video Sensor Network Platform and compatible DASH (WVSNP-DASH)
are introduced. The platform's goal is to usher video as a data element that
can be integrated into traditional and non-Internet networks. A low cost,
scalable node is built from the ground up to be fully compatible with the
Internet of Things Machine to Machine (M2M) concept, as well as the ability to
be easily re-targeted to new applications in a short time. Flexi-WVSNP design
includes a multi-radio node, a middle-ware for sensor operation and
communication, a cross platform client facing data retriever/player framework,
scalable security as well as a cohesive but decoupled hardware and software
design.
ContributorsSeema, Adolph (Author) / Reisslein, Martin (Thesis advisor) / Kitchen, Jennifer (Committee member) / Seeling, Patrick (Committee member) / Zhang, Yanchao (Committee member) / Arizona State University (Publisher)
Created2017
Description
This thesis describes the design process used in the creation of a two stage cellular power amplifier. A background for understanding amplifier linearity, device properties, and ACLR estimation is provided. An outline of the design goals is given with a focus on linearity with high efficiency. The full design is broken into smaller elements which are discussed in detail. The main contribution of this thesis is the description of a novel interstage matching network topology for increasing efficiency. Ultimately the full amplifier design is simulated and compared to the measured results and design goals. It was concluded that the design was successful, and used in a commercially available product.
ContributorsSpivey, Erin (Author) / Aberle, James T., 1961- (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2012
Description
In thesis, a test time reduction (a low cost test) methodology for digitally-calibrated pipeline analog-to-digital converters (ADCs) is presented. A long calibration time is required in the final test to validate performance of these designs. To reduce total test time, optimized calibration technique and calibrated effective number of bits (ENOB) prediction from calibration coefficient will be presented. With the prediction technique, failed devices can be identified only without actual calibration. This technique reduces significant amount of time for the total test time.
ContributorsKim, Kibeom (Author) / Ozev, Sule (Thesis advisor) / Kitchen, Jennifer (Committee member) / Barnaby, Hugh (Committee member) / Arizona State University (Publisher)
Created2013