Matching Items (173)
Description
The theory of quantum electrodynamics predicts that beta decay of the neutron into a proton, electron, and anti-neutrino should be accompanied by a continuous spectrum of photons. A recent experiment, RDK I, reported the first detection of radiative decay photons from neutron beta decay with a branching ratio of (3.09 ± 0.32) × 10-3 in the energy range of 15 keV to 340 keV. This was achieved by prompt coincident detection of an electron and photon, in delayed coincidence with a proton. The photons were detected by using a single bar of bismuth germanate scintillating crystal coupled to an avalanche photodiode. This thesis deals with the follow-up experiment, RDK II, to measure the branching ratio at the level of approximately 1% and the energy spectrum at the level of a few percent. The most significant improvement of RDK II is the use of a photon detector with about an order of magnitude greater solid angle coverage than RDK I. In addition, the detectable energy range has been extended down to approximately 250 eV and up to the endpoint energy of 782 keV. This dissertation presents an overview of the apparatus, development of a new data analysis technique for radiative decay, and results for the ratio of electron-proton-photon coincident Repg to electron-proton coincident Rep events.
ContributorsO'Neill, Benjamin (Author) / Alarcon, Ricardo (Thesis advisor) / Drucker, Jeffery (Committee member) / Lebed, Richard (Committee member) / Comfort, Joseph (Committee member) / Chamberlin, Ralph (Committee member) / Arizona State University (Publisher)
Created2012
Description
Since its inception in 1973, the Endangered Species Act has been met with both praise and criticism. More than 40 years later, the Act is still polarizing, with proponents applauding its power to protect species and critics arguing against its perceived ineffectiveness and potential mismanagement. Recovery plans, which were required by the 1988 amendments to the Act, play an important role in organizing efforts to protect and recover species under the Act. In 1999, in an effort to evaluate the process, the Society for Conservation Biology commissioned an independent review of endangered species recovery planning. From these findings, the SCB made key recommendations for how management agencies could improve the recovery planning process, after which the Fish and Wildlife Service and the National Marine Fisheries Service redrafted their recovery planning guidelines. One important recommendation called for recovery plans to make threats a primary focus, including organizing and prioritizing recovery tasks for threat abatement. Here, I seek to determine the extent to which SCB recommendations were incorporated into these new guidelines, and if, in turn, the recommendations regarding threats manifested in recovery plans written under the new guidelines. I found that the guidelines successfully incorporated most SCB recommendations, except those that addressed monitoring. As a result, recent recovery plans have improved in their treatment of threats, but still fail to adequately incorporate threat monitoring. This failure suggests that developing clear guidelines for monitoring should be an important priority in future ESA recovery planning.
ContributorsTroyer, Caitlin (Author) / Gerber, Leah (Thesis advisor) / Minteer, Ben (Committee member) / Guston, David (Committee member) / Arizona State University (Publisher)
Created2014
Description
This dissertation presents research findings on the three materials systems: lateral Si nanowires (SiNW), In2Se3/Bi2Se3 heterostructures and graphene. The first part of the thesis was focused on the growth and characterization of lateral SiNW. Lateral here refers to wires growing along the plane of substrate; vertical NW on the other hand grow out of the plane of substrate. It was found, using the Au-seeded vapor – liquid – solid technique, that epitaxial single-crystal SiNW can be grown laterally along Si(111) substrates that have been miscut toward [11− 2]. The ratio of lateral-to-vertical NW was found to increase as the miscut angle increased and as disilane pressure and substrate temperature decreased. Based on this observation, growth parameters were identified whereby all of the deposited Au seeds formed lateral NW. Furthermore, the nanofaceted substrate guided the growth via a mechanism that involved pinning of the trijunction at the liquid/solid interface of the growing nanowire.
Next, the growth of selenide heterostructures was explored. Specifically, molecular beam epitaxy was utilized to grow In2Se3 and Bi2Se3 films on h-BN, highly oriented pyrolytic graphite and Si(111) substrates. Growth optimizations of In2Se3 and Bi2Se3 films were carried out by systematically varying the growth parameters. While the growth of these films was demonstrated on h-BN and HOPG surface, the majority of the effort was focused on growth on Si(111). Atomically flat terraces that extended laterally for several hundred nm, which were separated by single quintuple layer high steps characterized surface of the best In2Se3 films grown on Si(111). These In2Se3 films were suitable for subsequent high quality epitaxy of Bi2Se3 .
The last part of this dissertation was focused on a recently initiated and ongoing study of graphene growth on liquid metal surfaces. The initial part of the study comprised a successful modification of an existing growth system to accommodate graphene synthesis and process development for reproducible graphene growth. Graphene was grown on Cu, Au and AuCu alloys at varioua conditions. Preliminary results showed triangular features on the liquid part of the Cu metal surface. For Au, and AuCu alloys, hexagonal features were noticed both on the solid and liquid parts.
Next, the growth of selenide heterostructures was explored. Specifically, molecular beam epitaxy was utilized to grow In2Se3 and Bi2Se3 films on h-BN, highly oriented pyrolytic graphite and Si(111) substrates. Growth optimizations of In2Se3 and Bi2Se3 films were carried out by systematically varying the growth parameters. While the growth of these films was demonstrated on h-BN and HOPG surface, the majority of the effort was focused on growth on Si(111). Atomically flat terraces that extended laterally for several hundred nm, which were separated by single quintuple layer high steps characterized surface of the best In2Se3 films grown on Si(111). These In2Se3 films were suitable for subsequent high quality epitaxy of Bi2Se3 .
The last part of this dissertation was focused on a recently initiated and ongoing study of graphene growth on liquid metal surfaces. The initial part of the study comprised a successful modification of an existing growth system to accommodate graphene synthesis and process development for reproducible graphene growth. Graphene was grown on Cu, Au and AuCu alloys at varioua conditions. Preliminary results showed triangular features on the liquid part of the Cu metal surface. For Au, and AuCu alloys, hexagonal features were noticed both on the solid and liquid parts.
ContributorsRathi, Somilkumar J (Author) / Drucker, Jeffery (Thesis advisor) / Smith, David (Committee member) / Chen, Tingyong (Committee member) / Arizona State University (Publisher)
Created2014
Description
This dissertation examines the nexus of three trends in electricity systems transformations underway worldwide—the scale-up of renewable energy, regionalization, and liberalization. Interdependent electricity systems are being envisioned that require partnership and integration across power disparities. This research explores how actors in the Mediterranean region envisioned a massive scale-up of renewable energy within a single electricity system and market across Europe, North Africa, and the Middle East. It asks: How are regional sociotechnical systems envisioned? What are the anticipated consequences of a system for a region with broad disparities and deep sociopolitical differences? What can be learned about energy justice by examining this vision at multiple scales? A sociotechnical systems framework is used to analyze energy transformations, interweaving the technical aspects with politics, societal effects, and political development issues. This research utilized mixed qualitative methods to analyze Mediterranean electricity transformations at multiple scales, including fieldwork in Morocco and Germany, document analysis, and event ethnography. Each scale—from a global history of concentrating solar power technologies to a small village in Morocco—provides a different lens on the sociotechnical system and its implications for justice. This study updates Thomas Hughes’ Networks of Power, the canonical history of the sociotechnical development of electricity systems, by adding new aspects to sociotechnical electricity systems theory. First, a visioning process now plays a crucial role in guiding innovation and has a lasting influence on the justice outcomes. Second, rather than simply providing people with heat and light, electrical power systems in the 21st century are called upon to address complex integrated solutions. Furthermore, building a sustainable energy system is now a retrofitting agenda, as system builders must graft new infrastructure on top of old systems. Third, the spatial and temporal aspects of sociotechnical energy systems should be amended to account for constructed geography and temporal complexity. Fourth, transnational electricity systems pose new challenges for politics and political development. Finally, this dissertation presents a normative framework for conceptualizing and evaluating energy justice. Multi-scalar, systems-level justice requires collating diverse ideas about energy justice, expanding upon them based on the empirical material, and evaluating them with this framework.
ContributorsMoore, Sharlissa (Author) / Hackett, Ed J. (Thesis advisor) / Minteer, Ben (Committee member) / Parmentier, Mary Jane (Committee member) / Wetmore, Jameson (Committee member) / Arizona State University (Publisher)
Created2015
Description
Over the past two decades there has been much discussion surrounding the potential of zoos as conservation institutions. Although zoos have clearly intensified their rhetorical and programmatic commitment to conservation (both ex situ and in situ), many critics remain skeptical of these efforts. This study was comprised of two parts: 1) an investigation of the general relationship between U.S. zoological institutions and the conservation agenda, and 2) a more specific single case study of conservation engagement and institutional identity at the Phoenix Zoo. Methods included extensive literature review, expert interviews with scholars and zoo professionals, site visits to the Phoenix Zoo and archival research. I found that the Phoenix Zoo is in the process of consciously creating a conservation-centered institutional identity by implementing and publicizing various conservation initiatives. Despite criticism of the embrace of conservation by zoos today, these institutions will be increasingly important agents of biodiversity protection and conservation education in this century.
ContributorsLove, Karen (Author) / Minteer, Ben (Thesis advisor) / Kinzig, Ann (Committee member) / Collins, James (Committee member) / Arizona State University (Publisher)
Created2014
Description
Off-axis electron holography (EH) has been used to characterize electrostatic potential, active dopant concentrations and charge distribution in semiconductor nanostructures, including ZnO nanowires (NWs) and thin films, ZnTe thin films, Si NWs with axial p-n junctions, Si-Ge axial heterojunction NWs, and Ge/LixGe core/shell NW.
The mean inner potential (MIP) and inelastic mean free path (IMFP) of ZnO NWs have been measured to be 15.3V±0.2V and 55±3nm, respectively, for 200keV electrons. These values were then used to characterize the thickness of a ZnO nano-sheet and gave consistent values. The MIP and IMFP for ZnTe thin films were measured to be 13.7±0.6V and 46±2nm, respectively, for 200keV electrons. A thin film expected to have a p-n junction was studied, but no signal due to the junction was observed. The importance of dynamical effects was systematically studied using Bloch wave simulations.
The built-in potentials in Si NWs across the doped p-n junction and the Schottky junction due to Au catalyst were measured to be 1.0±0.3V and 0.5±0.3V, respectively. Simulations indicated that the dopant concentrations were ~1019cm-3 for donors and ~1017 cm-3 for acceptors. The effects of positively charged Au catalyst, a possible n+-n--p junction transition region and possible surface charge, were also systematically studied using simulations.
Si-Ge heterojunction NWs were studied. Dopant concentrations were extracted by atom probe tomography. The built-in potential offset was measured to be 0.4±0.2V, with the Ge side lower. Comparisons with simulations indicated that Ga present in the Si region was only partially activated. In situ EH biasing experiments combined with simulations indicated the B dopant in Ge was mostly activated but not the P dopant in Si. I-V characteristic curves were measured and explained using simulations.
The Ge/LixGe core/shell structure was studied during lithiation. The MIP for LixGe decreased with time due to increased Li content. A model was proposed to explain the lower measured Ge potential, and the trapped electron density in Ge core was calculated to be 3×1018 electrons/cm3. The Li amount during lithiation was also calculated using MIP and volume ratio, indicating that it was lower than the fully lithiated phase.
The mean inner potential (MIP) and inelastic mean free path (IMFP) of ZnO NWs have been measured to be 15.3V±0.2V and 55±3nm, respectively, for 200keV electrons. These values were then used to characterize the thickness of a ZnO nano-sheet and gave consistent values. The MIP and IMFP for ZnTe thin films were measured to be 13.7±0.6V and 46±2nm, respectively, for 200keV electrons. A thin film expected to have a p-n junction was studied, but no signal due to the junction was observed. The importance of dynamical effects was systematically studied using Bloch wave simulations.
The built-in potentials in Si NWs across the doped p-n junction and the Schottky junction due to Au catalyst were measured to be 1.0±0.3V and 0.5±0.3V, respectively. Simulations indicated that the dopant concentrations were ~1019cm-3 for donors and ~1017 cm-3 for acceptors. The effects of positively charged Au catalyst, a possible n+-n--p junction transition region and possible surface charge, were also systematically studied using simulations.
Si-Ge heterojunction NWs were studied. Dopant concentrations were extracted by atom probe tomography. The built-in potential offset was measured to be 0.4±0.2V, with the Ge side lower. Comparisons with simulations indicated that Ga present in the Si region was only partially activated. In situ EH biasing experiments combined with simulations indicated the B dopant in Ge was mostly activated but not the P dopant in Si. I-V characteristic curves were measured and explained using simulations.
The Ge/LixGe core/shell structure was studied during lithiation. The MIP for LixGe decreased with time due to increased Li content. A model was proposed to explain the lower measured Ge potential, and the trapped electron density in Ge core was calculated to be 3×1018 electrons/cm3. The Li amount during lithiation was also calculated using MIP and volume ratio, indicating that it was lower than the fully lithiated phase.
ContributorsGan, Zhaofeng (Author) / Mccartney, Martha R (Thesis advisor) / Smith, David J. (Thesis advisor) / Drucker, Jeffery (Committee member) / Bennett, Peter A (Committee member) / Arizona State University (Publisher)
Created2015
Description
Group III-nitride semiconductors have attracted much attention for applications on high brightness light-emitting diodes (LEDs) and laser diodes (LDs) operating in the visible and ultra-violet spectral range using indium gallium nitride in the active layer. However, the device efficiency in the green to red range is limited by quantum-confined Stark effects resulting from the lattice mismatch between GaN and InGaN. In this dissertation, the optical and micro-structural properties of GaN-based light emitting structures have been analyzed and correlated by utilizing cathodoluminescence and transmission electron microscopy techniques. In the first section, optimization of the design of GaN-based lasers diode structures is presented. The thermal strain present in the GaN underlayer grown on sapphire substrates causes a strain-induced wavelength shift. The insertion of an InGaN waveguide mitigates the mismatch strain at the interface between the InGaN quantum well and the GaN quantum barrier. The second section of the thesis presents a study of the characteristics of thick non-polar m-plane InGaN films and of LED structures containing InGaN quantum wells, which minimize polarization-related electric fields. It is found that in some cases the in-plane piezoelectric fields can still occur due to the existence of misfit dislocations which break the continuity of the film. In the final section, the optical and structural properties of InGaAlN quaternary alloys are analyzed and correlated. The composition of the components of the film is accurately determined by Rutherford backscattering spectroscopy.
ContributorsHuang, Yu (Author) / Ponce, Fernando A. (Thesis advisor) / Tsen, Kong-Thon (Committee member) / Treacy, Michael (Committee member) / Drucker, Jeffery (Committee member) / Culbertson, Robert (Committee member) / Arizona State University (Publisher)
Created2011
Description
Ge1-ySny alloys represent a new class of photonic materials for integrated optoelectronics on Si. In this work, the electrical and optical properties of Ge1-ySny alloy films grown on Si, with concentrations in the range 0 ≤ y ≤ 0.04, are studied via a variety of methods. The first microelectronic devices from GeSn films were fabricated using newly developed CMOS-compatible protocols, and the devices were characterized with respect to their electrical properties and optical response. The detectors were found to have a detection range that extends into the near-IR, and the detection edge is found to shift to longer wavelengths with increasing Sn content, mainly due to the compositional dependence of the direct band gap E0. With only 2 % Sn, all of the telecommunication bands are covered by a single detector. Room temperature photoluminescence was observed from GeSn films with Sn content up to 4 %. The peak wavelength of the emission was found to shift to lower energies with increasing Sn content, corresponding to the decrease in the direct band gap E0 of the material. An additional peak in the spectrum was assigned to the indirect band gap. The separation between the direct and indirect peaks was found to decrease with increasing Sn concentration, as expected. Electroluminescence was also observed from Ge/Si and Ge0.98Sn0.02 photodiodes under forward bias, and the luminescence spectra were found to match well with the observed photoluminescence spectra. A theoretical expression was developed for the luminescence due to the direct band gap and fit to the data.
ContributorsMathews, Jay (Author) / Menéndez, Jose (Thesis advisor) / Kouvetakis, John (Thesis advisor) / Drucker, Jeffery (Committee member) / Chizmeshya, Andrew (Committee member) / Ponce, Fernando (Committee member) / Arizona State University (Publisher)
Created2011
Description
This dissertation analyzes the way in which leaders of certain Taiwanese Buddhist organizations associated with a strand of Buddhist modernism called "humanistic Buddhism" use discourse and rhetoric to make environmentalism meaningful to their members. It begins with an assessment of the field of religion and ecology, situating it in the context of secular environmental ethics. It identifies rhetoric and discourse as important but under acknowledged elements in literature on environmental ethics, both religious and secular, and relates this lack of attention to rhetoric to the presence of a problematic gap between environmental ethics theory and environmentalist practice. This dissertation develops a methodology of rhetorical analysis that seeks to assess how rhetoric contributes to alleviating this gap in religious environmentalism. In particular, this dissertation analyzes the development of environmentalism as a major element of humanistic Buddhist groups in Taiwan and seeks to show that a rhetorical analysis helps demonstrate how these organizations have sought to make environmentalism a meaningful subject of contemporary Buddhist religiosity. This dissertation will present an extended analysis of the concept of "spiritual environmentalism," a term developed and promoted by the late Ven. Shengyan (1930-2009), founder of the Taiwanese Buddhist organization Dharma Drum Mountain. Furthermore, this dissertation suggests that the rhetorical methodology proposed herein offers offers a direction for scholars to more effectively engage with religion and ecology in ways that address both descriptive/analytic approaches and constructive engagements with various forms of religious environmentalism.
ContributorsClippard, Seth (Author) / Chen, Huaiyu (Thesis advisor) / Tirosh-Samuelson, Hava (Committee member) / Bokenkamp, Stephen (Committee member) / Tillman, Hoyt (Committee member) / Minteer, Ben (Committee member) / Arizona State University (Publisher)
Created2012
Description
Raman scattering from Ge-Si core-shell nanowires is investigated theoretically and experimentally. A theoretical model that makes it possible to extract quantitative strain information from the measured Raman spectra is presented for the first time. Geometrical and elastic simplifications are introduced to keep the model analytical, which facilitates comparison with experimental results. In particular, the nanowires are assumed to be cylindrical, and their elastic constants isotropic. The simple analytical model is subsequently validated by performing numerical calculations using realistic nanowire geometries and cubic, anisotropic elastic constants. The comparison confirms that the analytic model is an excellent approximation that greatly facilitates quantitative Raman work, with expected errors in the strain determination that do not exceed 10%. Experimental Raman spectra of a variety of core-shell nanowires are presented, and the strain in the nanowires is assessed using the models described above. It is found that all structures present a significant degree of strain relaxation relative to ideal, fully strained Ge-Si core-shell structures. The analytical models are modified to quantify this strain relaxation.
ContributorsSingh, Rachna (Author) / Menéndez, Jose (Thesis advisor) / Drucker, Jeffery (Committee member) / Ponce, Fernando (Committee member) / Tsen, Kong-Thon (Committee member) / Bennett, Peter (Committee member) / Arizona State University (Publisher)
Created2011