Filtering by
- Member of: Programs and Communities
- Member of: Theses and Dissertations
This study analyzes the feasibility of using algae cultivated from wastewater effluent to produce a biodiesel feedstock. The goal was to determine if the energy produced was greater than the operational energy consumed without consideration to constructing the system as well as the emissions and economic value associated with the process.
Four scenarios were created:
1) high-lipid, dry extraction.
2) high-lipid, wet extraction.
3) low-lipid, dry extraction.
4) low-lipid, wet extraction.
In all cases, the system required more energy than it produced. In high lipid scenarios, the energy produced is close to the energy consumed, and a positive net energy balance may be achieved with minor improvements in technology or accounting for coproducts. In the low lipid scenarios, the energy balance is too negative to be considered feasible. Therefore the lipid content affects the decision to implement algae cultivation.
The dry extraction and the wet extraction both require some level of mechanical drying and this makes the two methods yield similar results in terms of the energy analysis. Therefore, the extraction method does not dramatically affect the decision for implementing algae-based oil production from an energetic standpoint. The economic value of the oil in both high lipid scenarios results in a net profit despite the negative net energy. Emission calculations resulted in avoiding a significant amount of CO2 for high lipid scenarios but not for the low lipid scenarios. The CO2 avoided does not account for non-lipid biomass, so this number is an underestimation of the final CO2 avoided from the end products.
While the term "CO2 avoided" has been used for this study, it should be noted that this CO2 would be emitted upon use as a fuel source. These emissions, however, are not “new” CO2 because it has already been emitted and is being captured and recycled. Currently, literature is very divisive on the lipid content present in algae and this study shows that lipid content has a tremendous affect on energy and emissions impacts. The type of algae that can grow in wastewater effluent also should be investigated as well as the conditions that promote high lipid accumulation. The dewatering phase must be improved as it is extremely energy intensive and dominates the operational energy balance.
In order to compete, wet extraction must have a much more significant effect on the drying phase and must avoid the use of the human toxicants methanol and chloroform. Additionally, while the construction phase was beyond the scope of this project it may be a critical aspect in determining the feasibility these systems. Future research in this field should focus on lipid production, optimizing the belt dryer or finding a different method of dewatering, and allocating the coproducts.
The research topic for this assignment is shrimp farming in Thailand located throughout the coastal areas of the southern, eastern, and central regions of the country. Thailand’s huge shrimp export driven industry represents one of the largest in the world accounting for over twenty-five percent of food exports out of the country (Sriboonchitta & Wiboonpongse, n.d.).
Specific research questions include:
1. What are the current unsustainable practices in shrimp farm production?
2. In what part of the life cycle should intervention take place?
3. What does a sustainable shrimp farming practice look like in the future?
Undoped CdTe/MgCdTe DHs are first grown in order to determine the material quality of the CdTe epilayer and to optimize the growth conditions. DH samples show strong photoluminescence with over double the intensity as that of a GaAs/AlGaAs DH with an identical layer structure. Time-resolved photoluminescence of the CdTe/MgCdTe DH gives a carrier lifetime of up to 179 ns for a 2 µm thick CdTe layer, which is more than one order of magnitude longer than that of polycrystalline CdTe films. MgCdTe barrier layers are found to be effective at confining photogenerated carriers and have a relatively low interface recombination velocity of 461 cm/s. The optimal growth temperature and Cd/Te flux ratio is determined to be 265 °C and 1.5, respectively.
Monocrystalline ZnTe/CdTe/MgCdTe P-n-N DH solar cells are designed, grown, processed into solar cell devices, and characterized. A maximum efficiency of 6.11 % is demonstrated for samples without an anti-reflection coating. The low efficiency is mainly due to the low open-circuit voltage (Voc), which is attributed to high dark current caused by interface recombination at the ZnTe/CdTe interface. Low-temperature measurements show a linear increase in Voc with decreasing temperature down to 77 K, which suggests that the room-temperature operation is limited by non-radiative recombination. An open-circuit voltage of 1.22 V and an efficiency of 8.46 % is demonstrated at 77 K. It is expected that a coherently strained MgCdTe/CdTe/MgCdTe DH solar cell design will produce higher efficiency and Voc compared to the ZnTe/CdTe/MgCdTe design with relaxed ZnTe layer.
The developed highly sensitive micro-strain sensing technique differs from the existing strain mapping techniques, such as digital image correlation (DIC)/micro-Moiré techniques, in terms of working mechanism, by filling a technology gap that requires high spatial resolution while simultaneously maintaining a large field-of-view. The strain sensing mechanism relies on the scanning of a tightly focused laser beam onto the grating that is on the sample surface to detect the change in the diffracted beam angle as a result of the strain. Gratings are fabricated on the target substrates to serve as strain sensors, which carries the strain information in the form of variations in the grating period. The geometric structure of the optical system inherently ensures the high sensitivity for the strain sensing, where the nanoscale change of the grating period is amplified by almost six orders into a diffraction peak shift on the order of several hundred micrometers. It significantly amplifies the small signal measurements so that the desired sensitivity and accuracy can be achieved.
The important features, such as strain sensitivity and spatial resolution, for the strain sensing technique are investigated to evaluate the technique. The strain sensitivity has been validated by measurements on homogenous materials with well known reference values of CTE (coefficient of thermal expansion). 10 micro-strain has been successfully resolved from the silicon CTE extraction measurements. Furthermore, the spatial resolution has been studied on predefined grating patterns, which are assembled to mimic the uneven strain distribution across the sample surface. A resolvable feature size of 10 µm has been achieved with an incident laser spot size of 50 µm in diameter.
In addition, the strain sensing technique has been applied to a composite sample made of SU8 and silicon, as well as the microelectronic packages for thermal strain mappings.
Anticipatory LCA seeks to overcome the paucity of data through scenario development and thermodynamic bounding analyses. Critical components of anticipatory LCA include:
1) Laboratory-scale inventory data collection for nano-manufacturing processes and
preliminary performance evaluation.
2) Thermodynamic modeling of manufacturing processes and developing scenarios of
efficiency gains informed by analogous material processing industries.
3) Use-phase bounding to report inventory data in a functional unit descriptive of
performance.
Together, these analyses may call attention to environmentally problematic processes or nanotechnologies before significant investments in R&D and infrastructure contribute to technology lock in. The following case study applies these components of anticipatory LCA to single wall carbon nanotube (SWCNT) manufacturing processes, compares the rapid improvements in SWCNT manufacturing to historic reductions in the embodied energy of aluminum, and discusses the use of SWCNTs as free-standing anodes in advanced lithium ion batteries.
