Matching Items (68)
Filtering by
- Genre: Masters Thesis
- Creators: Bakkaloglu, Bertan
Description
This work implements three switched mode power amplifier topologies namely inverse class-D (CMCD), push-pull class-E and inverse push-pull class-E, in a GaN-on-Si process for medium power level (5-10W) femto/pico-cells base-station applications. The presented power amplifiers address practical implementation design constraints and explore the fundamental performance limitations of switched-mode power amplifiers for cellular band. The designs are analyzed and compared with respect to non-idealities like finite on-resistance, finite-Q of inductors, bond-wire effects, input signal duty cycle, and supply and component variations. These architectures are designed for non-constant envelope inputs in the form of digitally modulated signals such as RFPWM, which undergo duty cycle variation. After comparing the three topologies, this work concludes that the inverse push-pull class-E power amplifier shows lower efficiency degradation at reduced duty cycles. For GaN based discrete power amplifiers which have less drain capacitance compared to GaAs or CMOS and where the switch loss is dominated by wire-bonds, an inverse push-pull class-E gives highest output power at highest efficiency. Push-pull class-E can give efficiencies comparable to inverse push-pull class-E in presence of bondwires on tuning the Zero-Voltage Switching (ZVS) network components but at a lower output power. Current-Mode Class-D (CMCD) is affected most by the presence of bondwires and gives least output power and efficiency compared to other two topologies. For systems dominated by drain capacitance loss or which has no bondwires, the CMCD and push-pull class-E gives better output power than inverse push-pull class-E. However, CMCD is more suitable for high breakdown voltage process.
ContributorsShukla, Shishir Ramasare (Author) / Kitchen, Jennifer N (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Trichopoulos, Georgios (Committee member) / Arizona State University (Publisher)
Created2015
Description
At modern-day intersections, traffic lights and stop signs assist human drivers to cross the intersection safely. Traffic congestion in urban road networks is a costly problem that affects all major cities. Efficiently operating intersections is largely dependent on accuracy and precision of human drivers, engendering a lingering uncertainty of attaining safety and high throughput. To improve the efficiency of the existing traffic network and mitigate the effects of human error in the intersection, many studies have proposed autonomous, intelligent transportation systems. These studies often involve utilizing connected autonomous vehicles, implementing a supervisory system, or both. Implementing a supervisory system is relatively more popular due to the security concerns of vehicle-to-vehicle communication. Even though supervisory systems are a step in the right direction for security, many supervisory systems’ safe operation solely relies on the promise of connected data being correct, making system reliability difficult to achieve. To increase fault-tolerance and decrease the effects of position uncertainty, this thesis proposes the Reliable and Robust Intersection Manager, a supervisory system that uses a separate surveillance system to dependably detect vehicles present in the intersection in order to create data redundancy for more accurate scheduling of connected autonomous vehicles. Adding the Surveillance System ensures that the temporal safety buffers between arrival times of connected autonomous vehicles are maintained. This guarantees that connected autonomous vehicles can traverse the intersection safely in the event of large vehicle controller error, a single rogue car entering the intersection, or a sybil attack. To test the proposed system given these fault-models, MATLAB® was used to create simulations in order to observe the functionality of R2IM compared to the state-of-the-art supervisory system, Robust Intersection Manager. Though R2IM is less efficient than the Robust Intersection Manager, it considers more fault models. The Robust Intersection Manager failed to maintain safety in the event of large vehicle controller errors and rogue cars, however R2IM resulted in zero collisions.
ContributorsDedinsky, Rachel (Author) / Shrivastava, Aviral (Thesis advisor) / Sen, Arunabha (Committee member) / Syrotiuk, Violet (Committee member) / Arizona State University (Publisher)
Created2019
Description
State-of-the-art automotive radars use multi-chip Frequency Modulated Continuous Wave (FMCW) radars to sense the environment around the car. FMCW radars are prone to interference as they operate over a narrow baseband bandwidth and use similar radio frequency (RF) chirps among them. Phase Modulated Continuous Wave radars (PMCW) are robust and insensitive to interference as they transmit signals over a wider bandwidth using spread spectrum technique. As more and more cars are equipped with FMCW radars illuminate the same environment, interference would soon become a serious issue. PMCW radars can be an effective solution to interference in the noisy FMCW radar environment. PMCW radars can be implemented in silicon as System-on-a-chip (SoC), suitable for Multiple-Input-Multiple-Output (MIMO) implementation and is highly programmable. PMCW radars do not require highly linear high frequency chirping oscillators thus reducing the size of the final solution.
This thesis aims to present a behavior model for this promising Digitally modulated radar (DMR) transceiver in Simulink/Matlab. The goal of this work is to create a model for the electronic system level framework that simulates the entire system with non-idealities. This model includes a Top Down Design methodology to understand the requirements of the individual modules’ performance and thus derive the specifications for implementing the real chip. Back annotation of the actual electrical modules’ performance to the model closes the design process loop. Using Simulink’s toolboxes, a passband and equivalent baseband model of the system is built for the transceiver with non-idealities of the components built in along with signal processing routines in Matlab. This model provides a platform for system evaluation and simulation for various system scenarios and use-cases of sensing using the environment around a moving car.
This thesis aims to present a behavior model for this promising Digitally modulated radar (DMR) transceiver in Simulink/Matlab. The goal of this work is to create a model for the electronic system level framework that simulates the entire system with non-idealities. This model includes a Top Down Design methodology to understand the requirements of the individual modules’ performance and thus derive the specifications for implementing the real chip. Back annotation of the actual electrical modules’ performance to the model closes the design process loop. Using Simulink’s toolboxes, a passband and equivalent baseband model of the system is built for the transceiver with non-idealities of the components built in along with signal processing routines in Matlab. This model provides a platform for system evaluation and simulation for various system scenarios and use-cases of sensing using the environment around a moving car.
ContributorsKalyan, Prassana (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Thesis advisor) / Garrity, Douglas (Committee member) / Arizona State University (Publisher)
Created2019
Description
The efficiency of spacecraft’s solar cells reduces over the course of their operation. Traditionally, they are configured to extract maximum power at the end of their life and not have a system which dynamically extracts the maximum power over their entire life. This work demonstrates the benefit of dynamic re-configuration of spacecraft’s solar arrays to access the full power available from the solar panels throughout their lifetime. This dynamic re-configuration is achieved using enhancement mode GaN devices as the switches due to their low Ron and small footprint.
This work discusses hardware Implementation challenges and a prototype board is designed using components-off-the-shelf (COTS) to study the behavior of photovoltaic (PV) panels with different configurations of switches between 5 PV cells. The measurement results from the board proves the feasibility of the idea, showing the power improvements of having the switch structure. The measurement results are used to simulate a 1kW satellite system and understand practical trade-offs of this idea in actual satellite power systems.
Additionally, this work also presents the implementation of CMOS controller integrated circuit (IC) in 0.18um technology. The CMOS controller IC includes switched-capacitor converters in open loop to provide the floating voltages required to drive the GaN switches. Each CMOS controller IC can drive 10 switches in series and parallel combination. Furthermore, the designed controller IC is expected to operate under 300MRad of total dose radiation, thus enabling the controller modules to be placed on the solar cell wings of the satellites.
This work discusses hardware Implementation challenges and a prototype board is designed using components-off-the-shelf (COTS) to study the behavior of photovoltaic (PV) panels with different configurations of switches between 5 PV cells. The measurement results from the board proves the feasibility of the idea, showing the power improvements of having the switch structure. The measurement results are used to simulate a 1kW satellite system and understand practical trade-offs of this idea in actual satellite power systems.
Additionally, this work also presents the implementation of CMOS controller integrated circuit (IC) in 0.18um technology. The CMOS controller IC includes switched-capacitor converters in open loop to provide the floating voltages required to drive the GaN switches. Each CMOS controller IC can drive 10 switches in series and parallel combination. Furthermore, the designed controller IC is expected to operate under 300MRad of total dose radiation, thus enabling the controller modules to be placed on the solar cell wings of the satellites.
ContributorsHeblikar, Anand N (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2019
Description
Point of Load (POL) DC-DC converters are increasingly used in space applications, data centres, electric vehicles, portable computers and devices and medical electronics. Heavy computing and processing capabilities of the modern devices have ushered the use of higher battery supply voltage to increase power storage. The need to address this consumer experience driven requirement has propelled the evolution of the next generation of small form-factor power converters which can operate with higher step down ratios while supplying heavy continuous load currents without sacrificing efficiency. Constant On-Time (COT) converter topology is capable of achieving stable operation at high conversion ratio with minimum off-chip components and small silicon area. This work proposes a Constant On-Time buck dc-dc converter for a wide dynamic input range and load currents from 100mA to 10A. Accuracy of this ripple based converter is improved by a unique voltage positioning technique which modulates the reference voltage to lower the average ripple profile close to the nominal output. Adaptive On-time block features a transient enhancement scheme to assist in faster voltage droop recovery when the output voltage dips below a defined threshold. UtilizingGallium Nitride (GaN) power switches enable the proposed converter to achieve very high efficiency while using smaller size inductor-capacitor (LC) power-stage. Use of novel Superjunction devices with higher drain-source blocking voltage simplifies the complex driver design and enables faster frequency of operation. It allows 1.8VComplementary Metal-Oxide Semiconductor (CMOS) devices to effectively drive GaNpower FETs which require 5V gate signal swing. The presented controller circuit uses internal ripple generation which reduces reliance on output cap equivalent series resistance (ESR) for loop stability and facilitates ripples reduction at the output. The ripple generation network is designed to provide ai
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
ContributorsJoshi, Omkar (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Long, Yu (Committee member) / Arizona State University (Publisher)
Created2019
Description
This work analyzes and develops a point-of-load (PoL) synchronous buck converter using enhancement-mode Gallium Nitride (e-GaN), with emphasis on optimizing reverse conduction loss by using a well-known technique of placing an anti-parallel Schottky diode across the synchronous power device. This work develops an improved analytical switching model for the GaN-based converter with the Schottky diode using piecewise linear approximations.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
ContributorsKoli, Gauri (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2020
Description
ABSTRACT As the technology length shrinks down, achieving higher gain is becoming very difficult in deep sub-micron technologies. As the supply voltages drop, cascodes are very difficult to implement and cascade amplifiers are needed to achieve sufficient gain with required output swing. This sets the fundamental limit on the SNR and hence the maximum resolution that can be achieved by ADC. With the RSD algorithm and the range overlap, the sub ADC can tolerate large comparator offsets leaving the linearity and accuracy requirement for the DAC and residue gain stage. Typically, the multiplying DAC requires high gain wide bandwidth op-amp and the design of this high gain op-amp becomes challenging in the deep submicron technologies. This work presents `A 12 bit 25MSPS 1.2V pipelined ADC using split CLS technique' in IBM 130nm 8HP process using only CMOS devices for the application of Large Hadron Collider (LHC). CLS technique relaxes the gain requirement of op-amp and improves the signal-to-noise ratio without increase in power or input sampling capacitor with rail-to-rail swing. An op-amp sharing technique has been incorporated with split CLS technique which decreases the number of op-amps and hence the power further. Entire pipelined converter has been implemented as six 2.5 bit RSD stages and hence decreases the latency associated with the pipelined architecture - one of the main requirements for LHC along with the power requirement. Two different OTAs have been designed to use in the split-CLS technique. Bootstrap switches and pass gate switches are used in the circuit along with a low power dynamic kick-back compensated comparator.
ContributorsSwaminathan, Visu Vaithiyanathan (Author) / Barnaby, Hugh (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Christen, Jennifer Blain (Committee member) / Arizona State University (Publisher)
Created2012
Description
This work presents two balanced power amplifier (PA) architectures, one at X-band and the other at K-band. The presented balanced PAs are designed for use in small satellite and cube satellite applications.The presented X-band PA employs wideband hybrid couplers to split input power to two commercial off-the-shelf (COTS) Gallium Nitride (GaN) monolithic microwave integrated circuit (MMIC) PAs and combine their output powers. The presented X-band balanced PA manufactured on a Rogers 4003C substrate yields increased small signal gain and saturated output power under continuous wave (CW) operation compared to the single MMIC PA used in the design under pulsed operation. The presented PA operates from 7.5 GHz to 11.5 GHz, has a maximum small signal gain of 36.3 dB, a maximum saturated power out of 40.0 dBm, and a maximum power added efficiency (PAE) of 38%.
Both a Wilkinson and a Gysel splitter and combiner are designed for use at K-band and their performance is compared. The presented K-band balanced PA uses Gysel power dividers and combiners with a GaN MMIC PA that is soon to be released in production.
ContributorsPearson, Katherine Elizabeth (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2023