Matching Items (7)
Filtering by
- All Subjects: Built-In Self-Test
- All Subjects: Radio--Transmitters and transmission.
- Creators: Ozev, Sule
Description
High speed current-steering DACs with high linearity are needed in today's applications such as wired and wireless communications, instrumentation, radar, and other direct digital synthesis (DDS) applications. However, a trade-off exists between the speed and resolution of Nyquist rate current-steering DACs. As the resolution increases, more transistor area is required to meet matching requirements for optimal linearity and thus, the overall speed of the DAC is limited.
In this thesis work, a 12-bit current-steering DAC was designed with current sources scaled below the required matching size to decrease the area and increase the overall speed of the DAC. By scaling the current sources, however, errors due to random mismatch between current sources will arise and additional calibration hardware is necessary to ensure 12-bit linearity. This work presents how to implement a self-calibration DAC that works to fix amplitude errors while maintaining a lower overall area. Additionally, the DAC designed in this thesis investigates the implementation feasibility of a data-interleaved architecture. Data interleaving can increase the total bandwidth of the DACs by 2 with an increase in SQNR by an additional 3 dB.
The final results show that the calibration method can effectively improve the linearity of the DAC. The DAC is able to run up to 400 MSPS frequencies with a 75 dB SFDR performance and above 87 dB SFDR performance at update rates of 200 MSPS.
In this thesis work, a 12-bit current-steering DAC was designed with current sources scaled below the required matching size to decrease the area and increase the overall speed of the DAC. By scaling the current sources, however, errors due to random mismatch between current sources will arise and additional calibration hardware is necessary to ensure 12-bit linearity. This work presents how to implement a self-calibration DAC that works to fix amplitude errors while maintaining a lower overall area. Additionally, the DAC designed in this thesis investigates the implementation feasibility of a data-interleaved architecture. Data interleaving can increase the total bandwidth of the DACs by 2 with an increase in SQNR by an additional 3 dB.
The final results show that the calibration method can effectively improve the linearity of the DAC. The DAC is able to run up to 400 MSPS frequencies with a 75 dB SFDR performance and above 87 dB SFDR performance at update rates of 200 MSPS.
ContributorsJankunas, Benjamin (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2014
Description
In this thesis, a Built-in Self Test (BiST) based testing solution is proposed to measure linear and non-linear impairments in the RF Transmitter path using analytical approach. Design issues and challenges with the impairments modeling and extraction in transmitter path are discussed. Transmitter is modeled for I/Q gain & phase mismatch, system non-linearity and DC offset using Matlab. BiST architecture includes a peak detector which includes a self mode mixer and 200 MHz filter. Self Mode mixing operation with filtering removes the high frequency signal contents and allows performing analysis on baseband frequency signals. Transmitter impairments were calculated using spectral analysis of output from the BiST circuitry using an analytical method. Matlab was used to simulate the system with known test impairments and impairment values from simulations were calculated based on system modeling in Mathematica. Simulated data is in good correlation with input test data along with very fast test time and high accuracy. The key contribution of the work is that, system impairments are extracted from transmitter response at baseband frequency using envelope detector hence eliminating the need of expensive high frequency ATE (Automated Test Equipments).
ContributorsGoyal, Nitin (Author) / Ozev, Sule (Thesis advisor) / Duman, Tolga (Committee member) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2011
Description
Built-in-Self-Test (BiST) for transmitters is a desirable choice since it eliminates the reliance on expensive instrumentation to do RF signal analysis. Existing on-chip resources, such as power or envelope detectors, or small additional circuitry can be used for BiST purposes. However, due to limited bandwidth, measurement of complex specifications, such as IQ imbalance, is challenging. In this work, a BiST technique to compute transmitter IQ imbalances using measurements out of a self-mixing envelope detector is proposed. Both the linear and non linear parameters of the RF transmitter path are extracted successfully. We first derive an analytical expression for the output signal. Using this expression, we devise test signals to isolate the effects of gain and phase imbalance, DC offsets, time skews and system nonlinearity from other parameters of the system. Once isolated, these parameters are calculated easily with a few mathematical operations. Simulations and hardware measurements show that the technique can provide accurate characterization of IQ imbalances. One of the glaring advantages of this method is that, the impairments are extracted from analyzing the response at baseband frequency and thereby eliminating the need of high frequency ATE (Automated Test Equipment).
ContributorsByregowda, Srinath (Author) / Ozev, Sule (Thesis advisor) / Cao, Yu (Committee member) / Yu, Hongbin (Committee member) / Arizona State University (Publisher)
Created2012
Description
RF transmitter manufacturers go to great extremes and expense to ensure that their product meets the RF output power requirements for which they are designed. Therefore, there is an urgent need for in-field monitoring of output power and gain to bring down the costs of RF transceiver testing and ensure product reliability. Built-in self-test (BIST) techniques can perform such monitoring without the requirement for expensive RF test equipment. In most BIST techniques, on-chip resources, such as peak detectors, power detectors, or envelope detectors are used along with frequency down conversion to analyze the output of the design under test (DUT). However, this conversion circuitry is subject to similar process, voltage, and temperature (PVT) variations as the DUT and affects the measurement accuracy. So, it is important to monitor BIST performance over time, voltage and temperature, such that accurate in-field measurements can be performed.
In this research, a multistep BIST solution using only baseband signals for test analysis is presented. An on-chip signal generation circuit, which is robust with respect to time, supply voltage, and temperature variations is used for self-calibration of the BIST system before the DUT measurement. Using mathematical modelling, an analytical expression for the output signal is derived first and then test signals are devised to extract the output power of the DUT. By utilizing a standard 180nm IBM7RF CMOS process, a 2.4GHz low power RF IC incorporated with the proposed BIST circuitry and on-chip test signal source is designed and fabricated. Experimental results are presented, which show this BIST method can monitor the DUT’s output power with +/- 0.35dB accuracy over a 20dB power dynamic range.
In this research, a multistep BIST solution using only baseband signals for test analysis is presented. An on-chip signal generation circuit, which is robust with respect to time, supply voltage, and temperature variations is used for self-calibration of the BIST system before the DUT measurement. Using mathematical modelling, an analytical expression for the output signal is derived first and then test signals are devised to extract the output power of the DUT. By utilizing a standard 180nm IBM7RF CMOS process, a 2.4GHz low power RF IC incorporated with the proposed BIST circuitry and on-chip test signal source is designed and fabricated. Experimental results are presented, which show this BIST method can monitor the DUT’s output power with +/- 0.35dB accuracy over a 20dB power dynamic range.
ContributorsGangula, Sudheer Kumar Reddy (Author) / Kitchen, Jennifer (Thesis advisor) / Ozev, Sule (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
Description
Due to high level of integration in RF System on Chip (SOC), the test access points are limited to the baseband and RF inputs/outputs of the system. This limited access poses a big challenge particularly for advanced RF architectures where calibration of internal parameters is necessary and ensure proper operation. Therefore low-overhead built-in Self-Test (BIST) solution for advanced RF transceiver is proposed. In this dissertation. Firstly, comprehensive BIST solution for RF polar transceivers using on-chip resources is presented. In the receiver, phase and gain mismatches degrade sensitivity and error vector magnitude (EVM). In the transmitter, delay skew between the envelope and phase signals and the finite envelope bandwidth can create intermodulation distortion (IMD) that leads to violation of spectral mask requirements. Characterization and calibration of these parameters with analytical model would reduce the test time and cost considerably. Hence, a technique to measure and calibrate impairments of the polar transceiver in the loop-back mode is proposed.
Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced.
Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method.
Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed.
Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.
Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced.
Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method.
Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed.
Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.
ContributorsJeong, Jae Woong (Author) / Ozev, Sule (Thesis advisor) / Kitchen, Jennifer (Committee member) / Cao, Yu (Committee member) / Ogras, Umit Y. (Committee member) / Arizona State University (Publisher)
Created2015
Description
As integrated technologies are scaling down, there is an increasing trend in the
process,voltage and temperature (PVT) variations of highly integrated RF systems.
Accounting for these variations during the design phase requires tremendous amount
of time for prediction of RF performance and optimizing it accordingly. Thus, there
is an increasing gap between the need to relax the RF performance requirements at
the design phase for rapid development and the need to provide high performance
and low cost RF circuits that function with PVT variations. No matter how care-
fully designed, RF integrated circuits (ICs) manufactured with advanced technology
nodes necessitate lengthy post-production calibration and test cycles with expensive
RF test instruments. Hence design-for-test (DFT) is proposed for low-cost and fast
measurement of performance parameters during both post-production and in-eld op-
eration. For example, built-in self-test (BIST) is a DFT solution for low-cost on-chip
measurement of RF performance parameters. In this dissertation, three aspects of
automated test and calibration, including DFT mathematical model, BIST hardware
and built-in calibration are covered for RF front-end blocks.
First, the theoretical foundation of a post-production test of RF integrated phased
array antennas is proposed by developing the mathematical model to measure gain
and phase mismatches between antenna elements without any electrical contact. The
proposed technique is fast, cost-efficient and uses near-field measurement of radiated
power from antennas hence, it requires single test setup, it has easy implementation
and it is short in time which makes it viable for industrialized high volume integrated
IC production test.
Second, a BIST model intended for the characterization of I/Q offset, gain and
phase mismatch of IQ transmitters without relying on external equipment is intro-
duced. The proposed BIST method is based on on-chip amplitude measurement as
in prior works however,here the variations in the BIST circuit do not affect the target
parameter estimation accuracy since measurements are designed to be relative. The
BIST circuit is implemented in 130nm technology and can be used for post-production
and in-field calibration.
Third, a programmable low noise amplifier (LNA) is proposed which is adaptable
to different application scenarios depending on the specification requirements. Its
performance is optimized with regards to required specifications e.g. distance, power
consumption, BER, data rate, etc.The statistical modeling is used to capture the
correlations among measured performance parameters and calibration modes for fast
adaptation. Machine learning technique is used to capture these non-linear correlations and build the probability distribution of a target parameter based on measurement results of the correlated parameters. The proposed concept is demonstrated by
embedding built-in tuning knobs in LNA design in 130nm technology. The tuning
knobs are carefully designed to provide independent combinations of important per-
formance parameters such as gain and linearity. Minimum number of switches are
used to provide the desired tuning range without a need for an external analog input.
process,voltage and temperature (PVT) variations of highly integrated RF systems.
Accounting for these variations during the design phase requires tremendous amount
of time for prediction of RF performance and optimizing it accordingly. Thus, there
is an increasing gap between the need to relax the RF performance requirements at
the design phase for rapid development and the need to provide high performance
and low cost RF circuits that function with PVT variations. No matter how care-
fully designed, RF integrated circuits (ICs) manufactured with advanced technology
nodes necessitate lengthy post-production calibration and test cycles with expensive
RF test instruments. Hence design-for-test (DFT) is proposed for low-cost and fast
measurement of performance parameters during both post-production and in-eld op-
eration. For example, built-in self-test (BIST) is a DFT solution for low-cost on-chip
measurement of RF performance parameters. In this dissertation, three aspects of
automated test and calibration, including DFT mathematical model, BIST hardware
and built-in calibration are covered for RF front-end blocks.
First, the theoretical foundation of a post-production test of RF integrated phased
array antennas is proposed by developing the mathematical model to measure gain
and phase mismatches between antenna elements without any electrical contact. The
proposed technique is fast, cost-efficient and uses near-field measurement of radiated
power from antennas hence, it requires single test setup, it has easy implementation
and it is short in time which makes it viable for industrialized high volume integrated
IC production test.
Second, a BIST model intended for the characterization of I/Q offset, gain and
phase mismatch of IQ transmitters without relying on external equipment is intro-
duced. The proposed BIST method is based on on-chip amplitude measurement as
in prior works however,here the variations in the BIST circuit do not affect the target
parameter estimation accuracy since measurements are designed to be relative. The
BIST circuit is implemented in 130nm technology and can be used for post-production
and in-field calibration.
Third, a programmable low noise amplifier (LNA) is proposed which is adaptable
to different application scenarios depending on the specification requirements. Its
performance is optimized with regards to required specifications e.g. distance, power
consumption, BER, data rate, etc.The statistical modeling is used to capture the
correlations among measured performance parameters and calibration modes for fast
adaptation. Machine learning technique is used to capture these non-linear correlations and build the probability distribution of a target parameter based on measurement results of the correlated parameters. The proposed concept is demonstrated by
embedding built-in tuning knobs in LNA design in 130nm technology. The tuning
knobs are carefully designed to provide independent combinations of important per-
formance parameters such as gain and linearity. Minimum number of switches are
used to provide the desired tuning range without a need for an external analog input.
ContributorsShafiee, Maryam (Author) / Ozev, Sule (Thesis advisor) / Diaz, Rodolfo (Committee member) / Ogras, Umit Y. (Committee member) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2018
Description
Recent advancements in communication standards, such as 5G demand transmitter hardware to support high data rates with high energy efficiency. With the revolution of communication standards, modulation schemes have become more complex and require high peak-to-average (PAPR) signals. In wireless transceiver hardware, the power amplifier (PA) consumes most of the transceiver’s DC power and is typically the bottleneck for transmitter linearity. Therefore, the transmitter’s performance directly depends on the PA. To support high PAPR signals, the PA must operate efficiently at its saturated and backoff output power. Maintaining high efficiency at both peak and backoff output power is challenging. One effective technique for addressing this problem is load modulation. Some of the prominent load-modulated PA architectures are outphasing PAs, load-modulated balanced amplifiers (LMBA), envelope elimination and restoration (EER), envelope tracking (ET), Doherty power amplifiers (DPA), and polar transmitters. Amongst them, the DPA is the most popular for infrastructure applications due to its simpler architecture compared to other techniques and linearizability with digital pre-distortion (DPD). Another crucial characteristic of progressing communication standards is wide signal bandwidths. High-efficiency power amplifiers like class J/F/F-1 and load-modulated PAs like the DPA exhibit narrowband performance because the amplifiers require precise output impedance terminations. Therefore, it is equally essential to develop adaptable PA solutions to process radio frequency (RF) signals with wide bandwidths. To support modern and future cellular infrastructure, RF PAs need to be innovated to increase the backoff power efficiency by two times or more and support ten times or more wider bandwidths than current state-of-the-art PAs. This work presents five RF PA analyses and implementations to support future wireless communications transmitter hardware. Chapter 2 presents an optimized output-matching network analysis and design to achieve extended output power backoff of the DPA. Chapters 3 and 4 unveil two bandwidth enhancement techniques for the DPA while maintaining extended output power backoff. Chapter 5 exhibits a dual-band hybrid mode PA design targeted for wideband applications. Chapter 6 presents a built-in self-test circuit integrated into a PA for output impedance monitoring. This can alleviate the PA performance degradation due to the variation in the PA's output load over frequency, process, and aging. All RF PAs in this dissertation are implemented using Gallium Nitride (GaN)-based high electron mobility transistors (HEMT), and the realized designs validate the proposed PAs' theories/architectures.
ContributorsRoychowdhury, Debatrayee (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Aberle, James (Committee member) / Arizona State University (Publisher)
Created2024