Matching Items (6)
Filtering by
- All Subjects: Engineering design
- All Subjects: Coordinate measuring machines
- All Subjects: Feature Fitting
- Genre: Academic theses
- Creators: Shah, Jami J.
Description
Creative design lies at the intersection of novelty and technical feasibility. These objectives can be achieved through cycles of divergence (idea generation) and convergence (idea evaluation) in conceptual design. The focus of this thesis is on the latter aspect. The evaluation may involve any aspect of technical feasibility and may be desired at component, sub-system or full system level. Two issues that are considered in this work are: 1. Information about design ideas is incomplete, informal and sketchy 2. Designers often work at multiple levels; different aspects or subsystems may be at different levels of abstraction Thus, high fidelity analysis and simulation tools are not appropriate for this purpose. This thesis looks at the requirements for a simulation tool and how it could facilitate concept evaluation. The specific tasks reported in this thesis are: 1. The typical types of information available after an ideation session 2. The typical types of technical evaluations done in early stages 3. How to conduct low fidelity design evaluation given a well-defined feasibility question A computational tool for supporting idea evaluation was designed and implemented. It was assumed that the results of the ideation session are represented as a morphological chart and each entry is expressed as some combination of a sketch, text and references to physical effects and machine components. Approximately 110 physical effects were identified and represented in terms of algebraic equations, physical variables and a textual description. A common ontology of physical variables was created so that physical effects could be networked together when variables are shared. This allows users to synthesize complex behaviors from simple ones, without assuming any solution sequence. A library of 16 machine elements was also created and users were given instructions about incorporating them. To support quick analysis, differential equations are transformed to algebraic equations by replacing differential terms with steady state differences), only steady state behavior is considered and interval arithmetic was used for modeling. The tool implementation is done by MATLAB; and a number of case studies are also done to show how the tool works. textual description. A common ontology of physical variables was created so that physical effects could be networked together when variables are shared. This allows users to synthesize complex behaviors from simple ones, without assuming any solution sequence. A library of 15 machine elements was also created and users were given instructions about incorporating them. To support quick analysis, differential equations are transformed to algebraic equations by replacing differential terms with steady state differences), only steady state behavior is considered and interval arithmetic was used for modeling. The tool implementation is done by MATLAB; and a number of case studies are also done to show how the tool works.
ContributorsKhorshidi, Maryam (Author) / Shah, Jami J. (Thesis advisor) / Wu, Teresa (Committee member) / Gel, Esma (Committee member) / Arizona State University (Publisher)
Created2014
Description
Dimensional Metrology is the branch of science that determines length, angular, and geometric relationships within manufactured parts and compares them with required tolerances. The measurements can be made using either manual methods or sampled coordinate metrology (Coordinate measuring machines). Manual measurement methods have been in practice for a long time and are well accepted in the industry, but are slow for the present day manufacturing. On the other hand CMMs are relatively fast, but these methods are not well established yet. The major problem that needs to be addressed is the type of feature fitting algorithm used for evaluating tolerances. In a CMM the use of different feature fitting algorithms on a feature gives different values, and there is no standard that describes the type of feature fitting algorithm to be used for a specific tolerance. Our research is focused on identifying the feature fitting algorithm that is best used for each type of tolerance. Each algorithm is identified as the one to best represent the interpretation of geometric control as defined by the ASME Y14.5 standard and on the manual methods used for the measurement of a specific tolerance type. Using these algorithms normative procedures for CMMs are proposed for verifying tolerances. The proposed normative procedures are implemented as software. Then the procedures are verified by comparing the results from software with that of manual measurements.
To aid this research a library of feature fitting algorithms is developed in parallel. The library consists of least squares, Chebyshev and one sided fits applied on the features of line, plane, circle and cylinder. The proposed normative procedures are useful for evaluating tolerances in CMMs. The results evaluated will be in accordance to the standard. The ambiguity in choosing the algorithms is prevented. The software developed can be used in quality control for inspection purposes.
To aid this research a library of feature fitting algorithms is developed in parallel. The library consists of least squares, Chebyshev and one sided fits applied on the features of line, plane, circle and cylinder. The proposed normative procedures are useful for evaluating tolerances in CMMs. The results evaluated will be in accordance to the standard. The ambiguity in choosing the algorithms is prevented. The software developed can be used in quality control for inspection purposes.
ContributorsVemulapalli, Prabath (Author) / Shah, Jami J. (Thesis advisor) / Davidson, Joseph K. (Committee member) / Takahashi, Timothy (Committee member) / Arizona State University (Publisher)
Created2014
Description
Conceptual design stage plays a critical role in product development. However, few systematic methods and tools exist to support conceptual design. The long term aim of this project is to develop a tool for facilitating holistic ideation for conceptual design. This research is a continuation of past efforts in ASU Design Automation Lab. In past research, an interactive software test bed (Holistic Ideation Tool - version 1) was developed to explore logical ideation methods. Ideation states were identified and ideation strategies were developed to overcome common ideation blocks. The next version (version 2) of the holistic ideation tool added Cascading Evolutionary Morphological Charts (CEMC) framework and intuitive ideation strategies (reframing, restructuring, random connection, and forced connection).
Despite these remarkable contributions, there exist shortcomings in the previous versions (version 1 and version 2) of the holistic ideation tool. First, there is a need to add new ideation methods to the holistic ideation tool. Second, the organizational framework provided by previous versions needs to be improved, and a holistic approach needs to be devised, instead of separate logical or intuitive approaches. Therefore, the main objective of this thesis is to make the improvements and to resolve technical issues that are involved in their implementation.
Towards this objective, a new web based holistic ideation tool (version 3) has been created. The new tool adds and integrates Knowledge Bases of Mechanisms and Components Off-The-Shelf (COTS) into logical ideation methods. Additionally, an improved CEMC framework has been devised for organizing ideas efficiently. Furthermore, the usability of the tool has been improved by designing and implementing a new graphical user interface (GUI) which is more user friendly. It is hoped that these new features will lead to a platform for the designers to not only generate creative ideas but also effectively organize and store them in the conceptual design stage. By placing it on the web for public use, the Testbed has the potential to be used for research on the ideation process by effectively collecting large amounts of data from designers.
Despite these remarkable contributions, there exist shortcomings in the previous versions (version 1 and version 2) of the holistic ideation tool. First, there is a need to add new ideation methods to the holistic ideation tool. Second, the organizational framework provided by previous versions needs to be improved, and a holistic approach needs to be devised, instead of separate logical or intuitive approaches. Therefore, the main objective of this thesis is to make the improvements and to resolve technical issues that are involved in their implementation.
Towards this objective, a new web based holistic ideation tool (version 3) has been created. The new tool adds and integrates Knowledge Bases of Mechanisms and Components Off-The-Shelf (COTS) into logical ideation methods. Additionally, an improved CEMC framework has been devised for organizing ideas efficiently. Furthermore, the usability of the tool has been improved by designing and implementing a new graphical user interface (GUI) which is more user friendly. It is hoped that these new features will lead to a platform for the designers to not only generate creative ideas but also effectively organize and store them in the conceptual design stage. By placing it on the web for public use, the Testbed has the potential to be used for research on the ideation process by effectively collecting large amounts of data from designers.
ContributorsNarsale, Sumit Sunil (Author) / Shah, Jami J. (Thesis advisor) / Davidson, Joseph K. (Committee member) / Wu, Teresa (Committee member) / Arizona State University (Publisher)
Created2014
Description
Design problem formulation is believed to influence creativity, yet it has received only modest attention in the research community. Past studies of problem formulation are scarce and often have small sample sizes. The main objective of this research is to understand how problem formulation affects creative outcome. Three research areas are investigated: development of a model which facilitates capturing the differences among designers' problem formulation; representation and implication of those differences; the relation between problem formulation and creativity.
This dissertation proposes the Problem Map (P-maps) ontological framework. P-maps represent designers' problem formulation in terms of six groups of entities (requirement, use scenario, function, artifact, behavior, and issue). Entities have hierarchies within each group and links among groups. Variables extracted from P-maps characterize problem formulation.
Three experiments were conducted. The first experiment was to study the similarities and differences between novice and expert designers. Results show that experts use more abstraction than novices do and novices are more likely to add entities in a specific order. Experts also discover more issues.
The second experiment was to see how problem formulation relates to creativity. Ideation metrics were used to characterize creative outcome. Results include but are not limited to a positive correlation between adding more issues in an unorganized way with quantity and variety, more use scenarios and functions with novelty, more behaviors and conflicts identified with quality, and depth-first exploration with all ideation metrics. Fewer hierarchies in use scenarios lower novelty and fewer links to requirements and issues lower quality of ideas.
The third experiment was to see if problem formulation can predict creative outcome. Models based on one problem were used to predict the creativity of another. Predicted scores were compared to assessments of independent judges. Quality and novelty are predicted more accurately than variety, and quantity. Backward elimination improves model fit, though reduces prediction accuracy.
P-maps provide a theoretical framework for formalizing, tracing, and quantifying conceptual design strategies. Other potential applications are developing a test of problem formulation skill, tracking students' learning of formulation skills in a course, and reproducing other researchers’ observations about designer thinking.
This dissertation proposes the Problem Map (P-maps) ontological framework. P-maps represent designers' problem formulation in terms of six groups of entities (requirement, use scenario, function, artifact, behavior, and issue). Entities have hierarchies within each group and links among groups. Variables extracted from P-maps characterize problem formulation.
Three experiments were conducted. The first experiment was to study the similarities and differences between novice and expert designers. Results show that experts use more abstraction than novices do and novices are more likely to add entities in a specific order. Experts also discover more issues.
The second experiment was to see how problem formulation relates to creativity. Ideation metrics were used to characterize creative outcome. Results include but are not limited to a positive correlation between adding more issues in an unorganized way with quantity and variety, more use scenarios and functions with novelty, more behaviors and conflicts identified with quality, and depth-first exploration with all ideation metrics. Fewer hierarchies in use scenarios lower novelty and fewer links to requirements and issues lower quality of ideas.
The third experiment was to see if problem formulation can predict creative outcome. Models based on one problem were used to predict the creativity of another. Predicted scores were compared to assessments of independent judges. Quality and novelty are predicted more accurately than variety, and quantity. Backward elimination improves model fit, though reduces prediction accuracy.
P-maps provide a theoretical framework for formalizing, tracing, and quantifying conceptual design strategies. Other potential applications are developing a test of problem formulation skill, tracking students' learning of formulation skills in a course, and reproducing other researchers’ observations about designer thinking.
ContributorsDinar, Mahmoud (Author) / Shah, Jami J. (Thesis advisor) / Langley, Pat (Committee member) / Davidson, Joseph K. (Committee member) / Lande, Micah (Committee member) / Ren, Yi (Committee member) / Arizona State University (Publisher)
Created2015
Description
Metal castings are selectively machined-based on dimensional control requirements. To ensure that all the finished surfaces are fully machined, each as-cast part needs to be measured and then adjusted optimally in its fixture. The topics of this thesis address two parts of this process: data translations and feature-fitting clouds of points measured on each cast part. For the first, a CAD model of the finished part is required to be communicated to the machine shop for performing various machining operations on the metal casting. The data flow must include GD&T specifications along with other special notes that may be required to communicate to the machinist. Current data exchange, among various digital applications, is limited to translation of only CAD geometry via STEP AP203. Therefore, an algorithm is developed in order to read, store and translate the data from a CAD file (for example SolidWorks, CREO) to a standard and machine readable format (ACIS format - *.sat). Second, the geometry of cast parts varies from piece to piece and hence fixture set-up parameters for each part must be adjusted individually. To predictively determine these adjustments, the datum surfaces, and to-be-machined surfaces are scanned individually and the point clouds reduced to feature fits. The scanned data are stored as separate point cloud files. The labels associated with the datum and to-be-machined (TBM) features are extracted from the *.sat file. These labels are further matched with the file name of the point cloud data to identify data for the respective features. The point cloud data and the CAD model are then used to fit the appropriate features (features at maximum material condition (MMC) for datums and features at least material condition (LMC) for TBM features) using the existing normative feature fitting (nFF) algorithm. Once the feature fitting is complete, a global datum reference frame (GDRF) is constructed based on the locating method that will be used to machine the part. The locating method is extracted from a fixture library that specifies the type of fixturing used to machine the part. All entities are transformed from its local coordinate system into the GDRF. The nominal geometry, fitted features, and the GD&T information are then stored in a neutral file format called the Constraint Tolerance Feature (CTF) Graph. The final outputs are then used to identify the locations of the critical features on each part and these are used to establish the adjustments for its setup prior to machining, in another module, not part of this thesis.
ContributorsRamnath, Satchit (Author) / Shah, Jami J. (Thesis advisor) / Davidson, Joseph (Committee member) / Hansford, Dianne (Committee member) / Arizona State University (Publisher)
Created2016
Description
The essence of this research is the reconciliation and standardization of feature fitting algorithms used in Coordinate Measuring Machine (CMM) software and the development of Inspection Maps (i-Maps) for representing geometric tolerances in the inspection stage based on these standardized algorithms. The i-Map is a hypothetical point-space that represents the substitute feature evaluated for an actual part in the inspection stage. The first step in this research is to investigate the algorithms used for evaluating substitute features in current CMM software. For this, a survey of feature fitting algorithms available in the literature was performed and then a case study was done to reverse engineer the feature fitting algorithms used in commercial CMM software. The experiments proved that algorithms based on least squares technique are mostly used for GD&T; inspection and this wrong choice of fitting algorithm results in errors and deficiency in the inspection process. Based on the results, a standardization of fitting algorithms is proposed in light of the definition provided in the ASME Y14.5 standard and an interpretation of manual inspection practices. Standardized algorithms for evaluating substitute features from CMM data, consistent with the ASME Y14.5 standard and manual inspection practices for each tolerance type applicable to planar features are developed. Second, these standardized algorithms developed for substitute feature fitting are then used to develop i-Maps for size, orientation and flatness tolerances that apply to their respective feature types. Third, a methodology for Statistical Process Control (SPC) using the I-Maps is proposed by direct fitting of i-Maps into the parent T-Maps. Different methods of computing i-Maps, namely, finding mean, computing the convex hull and principal component analysis are explored. The control limits for the process are derived from inspection samples and a framework for statistical control of the process is developed. This also includes computation of basic SPC and process capability metrics.
ContributorsMani, Neelakantan (Author) / Shah, Jami J. (Thesis advisor) / Davidson, Joseph K. (Committee member) / Farin, Gerald (Committee member) / Arizona State University (Publisher)
Created2011