Matching Items (4)
Filtering by
- All Subjects: Audio amplifiers--Design and construction.
- All Subjects: MOSFET
- Genre: Masters Thesis
- Creators: Barnaby, Hugh
- Creators: Chakraborty, Bijeta
- Creators: Peterson, Cory
- Member of: ASU Electronic Theses and Dissertations
- Resource Type: Text
Description
Efficiency of components is an ever increasing area of importance to portable applications, where a finite battery means finite operating time. Higher efficiency devices need to be designed that don't compromise on the performance that the consumer has come to expect. Class D amplifiers deliver on the goal of increased efficiency, but at the cost of distortion. Class AB amplifiers have low efficiency, but high linearity. By modulating the supply voltage of a Class AB amplifier to make a Class H amplifier, the efficiency can increase while still maintaining the Class AB level of linearity. A 92dB Power Supply Rejection Ratio (PSRR) Class AB amplifier and a Class H amplifier were designed in a 0.24um process for portable audio applications. Using a multiphase buck converter increased the efficiency of the Class H amplifier while still maintaining a fast response time to respond to audio frequencies. The Class H amplifier had an efficiency above the Class AB amplifier by 5-7% from 5-30mW of output power without affecting the total harmonic distortion (THD) at the design specifications. The Class H amplifier design met all design specifications and showed performance comparable to the designed Class AB amplifier across 1kHz-20kHz and 0.01mW-30mW. The Class H design was able to output 30mW into 16Ohms without any increase in THD. This design shows that Class H amplifiers merit more research into their potential for increasing efficiency of audio amplifiers and that even simple designs can give significant increases in efficiency without compromising linearity.
ContributorsPeterson, Cory (Author) / Bakkaloglu, Bertan (Thesis advisor) / Barnaby, Hugh (Committee member) / Kiaei, Sayfe (Committee member) / Arizona State University (Publisher)
Created2013
Description
Class D Amplifiers are widely used in portable systems such as mobile phones to achieve high efficiency. The demands of portable electronics for low power consumption to extend battery life and reduce heat dissipation mandate efficient, high-performance audio amplifiers. The high efficiency of Class D amplifiers (CDAs) makes them particularly attractive for portable applications. The Digital class D amplifier is an interesting solution to increase the efficiency of embedded systems. However, this solution is not good enough in terms of PWM stage linearity and power supply rejection. An efficient control is needed to correct the error sources in order to get a high fidelity sound quality in the whole audio range of frequencies. A fundamental analysis on various error sources due to non idealities in the power stage have been discussed here with key focus on Power supply perturbations driving the Power stage of a Class D Audio Amplifier. Two types of closed loop Digital Class D architecture for PSRR improvement have been proposed and modeled. Double sided uniform sampling modulation has been used. One of the architecture uses feedback around the power stage and the second architecture uses feedback into digital domain. Simulation & experimental results confirm that the closed loop PSRR & PS-IMD improve by around 30-40 dB and 25 dB respectively.
ContributorsChakraborty, Bijeta (Author) / Bakkaloglu, Bertan (Thesis advisor) / Garrity, Douglas (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2012
Description
The scaling of transistors has numerous advantages such as increased memory density, less power consumption and better performance; but on the other hand, they also give rise to many reliability issues. One of the major reliability issue is the hot carrier injection and the effect it has on device degradation over time which causes serious circuit malfunctions.
Hot carrier injection has been studied from early 1980's and a lot of research has been done on the various hot carrier injection mechanisms and how the devices get damaged due to this effect. However, most of the existing hot carrier degradation models do not consider the physics involved in the degradation process and they just calculate the change in threshold voltage for different stress voltages and time. Based on this, an analytical expression is formulated that predicts the device lifetime.
This thesis starts by discussing various hot carrier injection mechanisms and the effects it has on the device. Studies have shown charges getting trapped in gate oxide and interface trap generation are two mechanisms for device degradation. How various device parameters get affected due to these traps is discussed here. The physics based models such as lucky hot electron model and substrate current model are presented and gives an idea how the gate current and substrate current can be related to hot carrier injection and density of traps created.
Devices are stressed under various voltages and from the experimental data obtained, the density of trapped charges and interface traps are calculated using mid-gap technique. In this thesis, a simple analytical model based on substrate current is used to calculate the density of trapped charges in oxide and interface traps generated and it is a function of stress voltage and stress time. The model is verified against the data and the TCAD simulations. Finally, the analytical model is incorporated in a Verilog-A model and based on the surface potential method, the threshold voltage shift due to hot carrier stress is calculated.
Hot carrier injection has been studied from early 1980's and a lot of research has been done on the various hot carrier injection mechanisms and how the devices get damaged due to this effect. However, most of the existing hot carrier degradation models do not consider the physics involved in the degradation process and they just calculate the change in threshold voltage for different stress voltages and time. Based on this, an analytical expression is formulated that predicts the device lifetime.
This thesis starts by discussing various hot carrier injection mechanisms and the effects it has on the device. Studies have shown charges getting trapped in gate oxide and interface trap generation are two mechanisms for device degradation. How various device parameters get affected due to these traps is discussed here. The physics based models such as lucky hot electron model and substrate current model are presented and gives an idea how the gate current and substrate current can be related to hot carrier injection and density of traps created.
Devices are stressed under various voltages and from the experimental data obtained, the density of trapped charges and interface traps are calculated using mid-gap technique. In this thesis, a simple analytical model based on substrate current is used to calculate the density of trapped charges in oxide and interface traps generated and it is a function of stress voltage and stress time. The model is verified against the data and the TCAD simulations. Finally, the analytical model is incorporated in a Verilog-A model and based on the surface potential method, the threshold voltage shift due to hot carrier stress is calculated.
ContributorsMuthuseenu, Kiraneswar (Author) / Barnaby, Hugh (Thesis advisor) / Kozicki, Michael (Committee member) / Velo, Yago Gonzalez (Committee member) / Arizona State University (Publisher)
Created2017
Description
The existing compact models can reproduce the characteristics of MOSFETs in the temperature range of -40oC to 125oC. Some applications require circuits to operate over a wide temperature range consisting of temperatures below the specified range of existing compact models, requiring wide temperature range compact models for the design of such circuits. In order to develop wide temperature range compact models, fourteen different geometries of n-channel and p-channel MOSFETs manufactured in a 0.18μm mixed-signal process were electrically characterized over a temperature range of 40 K to 298 K. Electrical characterization included ID-VG and ID-VD under different drain, body and gate biases respectively. The effects of low-temperature operation on the performance of 0.18μm MOSFETs have been studied and discussed in terms of sub-threshold characteristics, threshold voltage, the effect of the body bias and linearity of the device. As it is well understood, the subthreshold slope, the threshold voltage, drive currents of the MOSFETs increase when the temperature of the MOSFETs is lowered, which makes it advantageous to operate the MOSFETs at low-temperatures. However the internal linearity gm1/gm3 of the MOSFETs degrades as the temperature of the MOSFETs is lowered, and the performance of the MOSFETs can be affected by the interface traps that exist in higher density close to conduction band and valence band energy levels, as the Fermi-level moves closer to bandgap edges when MOSFETs are operated at cryogenic temperatures.
ContributorsKathuria, Achal (Author) / Barnaby, Hugh (Thesis advisor) / Schroder, Dieter K. (Committee member) / Vermeire, Bert (Committee member) / Arizona State University (Publisher)
Created2010