Matching Items (4)
Filtering by
- All Subjects: Antennas (Electronics)
- All Subjects: Base station
- Creators: Aberle, James T
Description
This thesis is a study of Bandwidth limitation of basestation power amplifier and its Doherty application. Fundamentally, bandwidth of a power amplifier (PA) is limited by both its input and output prematch networks and its Doherty architecture, specifically the impedance inverter between the main and auxiliary amplifier. In this study, only the output prematch network and the Doherty architecture follows are being investigated. A new proposed impedance inverter in the Doherty architecture exhibits an extended bandwidth compared to traditional quarterwave line.
Base on the loadline analysis, output impedance of the power amplifier can be represented by a loadline resistor and an output shunt capacitor. Base on this simple model, the maximum allowed bandwidth of the output impedance of the power amplifier can be estimated using the Bode-Fano method. However, since power amplifier is in fact nonlinear, harmonic balance simulation is used to loadpull the device across a broad range of frequencies. Base on the simulated large signal impedance at maximum power, the prematch circuitry can be designed. On a system level, the prematch power amplifier is used in Doherty amplifier. Two different prematch circuitries, T- section and shunt L methods are investigated along with their comparison in the Doherty architecture at both back off power and peak power condition. The last section of the thesis will be incorporating the proposed impedance inverter structure between the main and auxiliary amplifiers.
The simulated results showed the shunt L prematch topology has the least impedance dispersion across frequency. Along with the new impedance inverter structure, the 65% efficiency bandwidth improves by 50% compared to the original impedance inverter structure at back off power level.
Base on the loadline analysis, output impedance of the power amplifier can be represented by a loadline resistor and an output shunt capacitor. Base on this simple model, the maximum allowed bandwidth of the output impedance of the power amplifier can be estimated using the Bode-Fano method. However, since power amplifier is in fact nonlinear, harmonic balance simulation is used to loadpull the device across a broad range of frequencies. Base on the simulated large signal impedance at maximum power, the prematch circuitry can be designed. On a system level, the prematch power amplifier is used in Doherty amplifier. Two different prematch circuitries, T- section and shunt L methods are investigated along with their comparison in the Doherty architecture at both back off power and peak power condition. The last section of the thesis will be incorporating the proposed impedance inverter structure between the main and auxiliary amplifiers.
The simulated results showed the shunt L prematch topology has the least impedance dispersion across frequency. Along with the new impedance inverter structure, the 65% efficiency bandwidth improves by 50% compared to the original impedance inverter structure at back off power level.
ContributorsYang, Nick (Author) / Pan, George (Committee member) / Aberle, James T (Committee member) / Yu, Hongyu (Committee member) / Arizona State University (Publisher)
Created2014
Description
In this dissertation a new wideband circular HIS is proposed. The circular periodicity made it possible to illuminate the surface with a cylindrical TEMz wave and; a novel technique is utilized to make it wideband. Two models are developed to analyze the
reflection characteristics of the proposed HIS.
The circularly symmetric high impedance surface is used as a ground plane for the design of a low-profile loop and spiral radiating elements. It is shown that a HIS with circular periodicity provides a wider operational bandwidth for curvilinear radiating elements such, such as loops and spirals, compared to canonical rectangular HISs.
It is also observed that, with the aid of a circular HIS ground plane the gain of a loop and a spiral increases compared to when a perfect magnetic conductor (PMC) or rectangular HIS is used as a ground plane. The circular HIS was fabricated and the loop and spiral elements were placed individually in close proximity to it.
Also, due to the growing demand for low-radar signature (RCS) antennas for advanced airborne vehicles, curved and flexible HIS ground planes, which meet both the aerodynamic and low RCS requirements, have recently become popular candidates within the antenna and microwave technology. This encouraged us, to propose a spherical HIS where a 2-D curvature is introduced to the previously designed flat HIS.
The major problem associated with spherical HIS is the impact of the curvature on its reflection properties. After characterization of the flat circular HIS, which is addressed in the first part of this dissertation, a spherical curvature is introduced to the flat circular HIS and its impact on the reflection properties was examined when it was illuminated with the same cylindrical TEMz wave. The same technique, as for the flat HIS ground plane, is utilized to make the spherical HIS wideband. A loop and spiral element were placed in the vicinity of the curved HIS and their performanceswere investigated. The HISs were also fabricated and measurements were conducted to verify the simulations. An excellent agreement was observed.
reflection characteristics of the proposed HIS.
The circularly symmetric high impedance surface is used as a ground plane for the design of a low-profile loop and spiral radiating elements. It is shown that a HIS with circular periodicity provides a wider operational bandwidth for curvilinear radiating elements such, such as loops and spirals, compared to canonical rectangular HISs.
It is also observed that, with the aid of a circular HIS ground plane the gain of a loop and a spiral increases compared to when a perfect magnetic conductor (PMC) or rectangular HIS is used as a ground plane. The circular HIS was fabricated and the loop and spiral elements were placed individually in close proximity to it.
Also, due to the growing demand for low-radar signature (RCS) antennas for advanced airborne vehicles, curved and flexible HIS ground planes, which meet both the aerodynamic and low RCS requirements, have recently become popular candidates within the antenna and microwave technology. This encouraged us, to propose a spherical HIS where a 2-D curvature is introduced to the previously designed flat HIS.
The major problem associated with spherical HIS is the impact of the curvature on its reflection properties. After characterization of the flat circular HIS, which is addressed in the first part of this dissertation, a spherical curvature is introduced to the flat circular HIS and its impact on the reflection properties was examined when it was illuminated with the same cylindrical TEMz wave. The same technique, as for the flat HIS ground plane, is utilized to make the spherical HIS wideband. A loop and spiral element were placed in the vicinity of the curved HIS and their performanceswere investigated. The HISs were also fabricated and measurements were conducted to verify the simulations. An excellent agreement was observed.
ContributorsAmiri, Mikal Askarian (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T (Committee member) / Bakkaloglu, Bertan (Committee member) / Trichopoulos, Georgios C (Committee member) / Arizona State University (Publisher)
Created2018
Description
To detect and resolve sub-wavelength features at optical frequencies, beyond the diffraction limit, requires sensors that interact with the electromagnetic near-field of those features. Most instruments operating in this modality scan a single detector element across the surface under inspection because the scattered signals from a multiplicity of such elements would end up interfering with each other. However, an alternative massively parallelized configuration, consisting of a remotely interrogating array of dipoles, capable of interrogating multiple adjacent areas of the surface at the same time, was proposed in 2002.
In the present work a remotely interrogating slot antenna inside a 60nm silver slab is designed which increases the signal to noise ratio of the original system. The antenna is tuned to resonance at 600nm range by taking advantage of the plasmon resonance properties of the metal’s negative permittivity and judicious shaping of the slot element. Full-physics simulations show the capability of detecting an 8nm particle using red light illumination. The sensitivity to the λ/78 particle is attained by detecting the change induced on the antenna’s far field signature by the proximate particle, a change that is 15dB greater than the scattering signature of the particle by itself.
To verify the capabilities of this technology in a readily accessible experimental environment, a radiofrequency scale model is designed using a meta-material to mimic the optical properties of silver in the 2GHz to 5GHz range. Various approaches to the replication of the metal’s behavior are explored in a trade-off between fidelity to the metal’s natural plasmon response, desired bandwidth of the demonstration, and
ii
manufacturability of the meta-material. The simulation and experimental results successfully verify the capability of the proposed near-field sensor in sub-wavelength detection and imaging not only as a proof of concept for optical frequencies but also as a potential imaging device for radio frequencies.
In the present work a remotely interrogating slot antenna inside a 60nm silver slab is designed which increases the signal to noise ratio of the original system. The antenna is tuned to resonance at 600nm range by taking advantage of the plasmon resonance properties of the metal’s negative permittivity and judicious shaping of the slot element. Full-physics simulations show the capability of detecting an 8nm particle using red light illumination. The sensitivity to the λ/78 particle is attained by detecting the change induced on the antenna’s far field signature by the proximate particle, a change that is 15dB greater than the scattering signature of the particle by itself.
To verify the capabilities of this technology in a readily accessible experimental environment, a radiofrequency scale model is designed using a meta-material to mimic the optical properties of silver in the 2GHz to 5GHz range. Various approaches to the replication of the metal’s behavior are explored in a trade-off between fidelity to the metal’s natural plasmon response, desired bandwidth of the demonstration, and
ii
manufacturability of the meta-material. The simulation and experimental results successfully verify the capability of the proposed near-field sensor in sub-wavelength detection and imaging not only as a proof of concept for optical frequencies but also as a potential imaging device for radio frequencies.
ContributorsMostafavi, Mahkamehossadat (Author) / Diaz, Rodolfo E (Thesis advisor) / Pan, George W (Committee member) / Aberle, James T (Committee member) / Ning, Cun-Zheng (Committee member) / Arizona State University (Publisher)
Created2016
Description
High Impedance Surfaces (HISs), which have been investigated extensively, have proven to be very efficient ground planes for low profile antenna applications due to their unique reflection phase characteristics. Another emerging research field among the microwave and antenna technologies is the design of flexible antennas and microwave circuits to be utilized in conformal applications. The combination of those two research topics gives birth to a third one, namely the design of Conformal or Flexible HISs (FHISs), which is the main subject of this dissertation. The problems associated with the FHISs are twofold: characterization and physical realization. The characterization involves the analysis of scattering properties of FHISs in the presence of plane wave and localized sources. For this purpose, an approximate analytical method is developed to characterize the reflection properties of a cylindrically curved FHIS. The effects of curvature on the reflection phase of the curved FHISs are examined. Furthermore, the effects of different types of currents, specifically the ones inherent to finite sized periodic structures, on the reflection phase characteristics are observed. After the reflection phase characterization of curved HISs, the performance of dipole antennas located in close proximity to a curved HIS are investigated, and the results are compared with the flat case. Different types of resonances that may occur for such a low-profile antenna application are discussed. The effects of curvature on the radiation performance of antennas are examined. Commercially available flexible materials are relatively thin which degrades the bandwidth of HISs. Another practical aspect, which is related to the substrate thickness, is the compactness of the surface. Because of the design limitations of conventional HISs, it is not possible to miniaturize the HIS and increase the bandwidth, simultaneously. To overcome this drawback, a novel HIS is proposed with a periodically perforated ground plane. Copper plated through holes are extremely vulnerable to bending and should be avoided at the bending parts of flexible circuits. Fortunately, if designed properly, the perforations on the ground plane may result in suppression of surface waves. Hence, metallic posts can be eliminated without hindering the surface wave suppression properties of HISs.
ContributorsDurgun, Ahmet Cemal (Author) / Balanis, Constantine A (Thesis advisor) / Aberle, James T (Committee member) / Yu, Hongyu (Committee member) / Bakkaloglu, Bertan (Committee member) / Arizona State University (Publisher)
Created2013