Filtering by
- All Subjects: Battery
- All Subjects: simulation of microinverter
- Creators: Qin, Jiangchao
- Member of: Theses and Dissertations
- Status: Published
The main aspect of this report studies the viability of Li-ion battery application in Battery Energy Storage System (BESS) in Modular multilevel converter (MMC). MMC-based BESS is a promising solution for grid-level battery energy storage to accelerate utilization and integration of intermittent renewable energy resources, i.e., solar and wind energy. When the battery units are directly integrated in submodules (SMs) without dc-dc interfaced converters, this configuration provides highest system efficiency and lowest cost. However, the lifetime of battery will be affected by the low-frequency components contained in arm currents, which has not been thoroughly investigated. This paper investigates impact of various low-frequency arm-current ripples on lifetime of Li-ion battery cells and evaluate performance of battery charging and discharging in an MMC-BESS without dc-dc interfaced converters.
important to increase the eciency and reliability of this emerging clean energy technologies.
This thesis focuses on modeling and reliability of solar micro inverters. In
order to make photovoltaics (PV) cost competitive with traditional energy sources,
the economies of scale have been guiding inverter design in two directions: large,
centralized, utility-scale (500 kW) inverters vs. small, modular, module level (300
W) power electronics (MLPE). MLPE, such as microinverters and DC power optimizers,
oer advantages in safety, system operations and maintenance, energy yield,
and component lifetime due to their smaller size, lower power handling requirements,
and module-level power point tracking and monitoring capability [1]. However, they
suer from two main disadvantages: rst, depending on array topology (especially
the proximity to the PV module), they can be subjected to more extreme environments
(i.e. temperature cycling) during the day, resulting in a negative impact to
reliability; second, since solar installations can have tens of thousands to millions of
modules (and as many MLPE units), it may be dicult or impossible to track and
repair units as they go out of service. Therefore identifying the weak links in this
system is of critical importance to develop more reliable micro inverters.
While an overwhelming majority of time and research has focused on PV module
eciency and reliability, these issues have been largely ignored for the balance
of system components. As a relatively nascent industry, the PV power electronics
industry does not have the extensive, standardized reliability design and testing procedures
that exist in the module industry or other more mature power electronics
industries (e.g. automotive). To do so, the critical components which are at risk and
their impact on the system performance has to be studied. This thesis identies and
addresses some of the issues related to reliability of solar micro inverters.
This thesis presents detailed discussions on various components of solar micro inverter
and their design. A micro inverter with very similar electrical specications in
comparison with commercial micro inverter is modeled in detail and veried. Components
in various stages of micro inverter are listed and their typical failure mechanisms
are reviewed. A detailed FMEA is conducted for a typical micro inverter to identify
the weak links of the system. Based on the S, O and D metrics, risk priority number
(RPN) is calculated to list the critical at-risk components. Degradation of DC bus
capacitor is identied as one the failure mechanism and the degradation model is built
to study its eect on the system performance. The system is tested for surge immunity
using standard ring and combinational surge waveforms as per IEEE 62.41 and
IEC 61000-4-5 standards. All the simulation presented in this thesis is performed
using PLECS simulation software.
A battery system is a promising technology that can improve monthly bill savings since a battery can store the solar energy and the off-peak grid energy and release it later during the on-peak hours. Sponsored by Salt River Project (SRP), a smart home model consists 1.35 kW PV panels, a 7.76 kWh lithium-ion battery and an adjustable resistive load bank was built on the roof of Engineering Research Center (ERC) building. For analysis, data was scaled up by 6/1.35 times to simulate a real residential PV setup. The testing data had been continuously recorded for more than one year (Aug.2014 - Oct.2015) and a battery charging strategy was developed based on those data. The work of this thesis deals with the idea of this charging strategy and the economic benefits this charging strategy can bring to the PV customers. Part of this research work has been wrote into a conference paper which is accepted by IEEE PES General Meeting 2016. A new and larger system has been installed on the roof with 6 kW PV modules and 6 kW output integrated electronics. This project will go on and the method come up by this thesis will be tested.
Lithium ion batteries are quintessential components of modern life. They are used to power smart devices — phones, tablets, laptops, and are rapidly becoming major elements in the automotive industry. Demand projections for lithium are skyrocketing with production struggling to keep up pace. This drive is due mostly to the rapid adoption of electric vehicles; sales of electric vehicles in 2020 are more than double what they were only a year prior. With such staggering growth it is important to understand how lithium is sourced and what that means for the environment. Will production even be capable of meeting the demand as more industries make use of this valuable element? How will the environmental impact of lithium affect growth? This thesis attempts to answer these questions as the world looks to a decade of rapid growth for lithium ion batteries.