Matching Items (3)
Filtering by
- All Subjects: Imaging
- All Subjects: Constant ON Time
- All Subjects: NASA JPL
- All Subjects: ROIC
- Creators: Long, Yu
Description
Readout Integrated Circuits(ROICs) are important components of infrared(IR) imag
ing systems. Performance of ROICs affect the quality of images obtained from IR
imaging systems. Contemporary infrared imaging applications demand ROICs that
can support large dynamic range, high frame rate, high output data rate, at low
cost, size and power. Some of these applications are military surveillance, remote
sensing in space and earth science missions and medical diagnosis. This work focuses
on developing a ROIC unit cell prototype for National Aeronautics and Space Ad
ministration(NASA), Jet Propulsion Laboratory’s(JPL’s) space applications. These
space applications also demand high sensitivity, longer integration times(large well
capacity), wide operating temperature range, wide input current range and immunity
to radiation events such as Single Event Latchup(SEL).
This work proposes a digital ROIC(DROIC) unit cell prototype of 30ux30u size,
to be used mainly with NASA JPL’s High Operating Temperature Barrier Infrared
Detectors(HOT BIRDs). Current state of the art DROICs achieve a dynamic range
of 16 bits using advanced 65-90nm CMOS processes which adds a lot of cost overhead.
The DROIC pixel proposed in this work uses a low cost 180nm CMOS process and
supports a dynamic range of 20 bits operating at a low frame rate of 100 frames per
second(fps), and a dynamic range of 12 bits operating at a high frame rate of 5kfps.
The total electron well capacity of this DROIC pixel is 1.27 billion electrons, enabling
integration times as long as 10ms, to achieve better dynamic range. The DROIC unit
cell uses an in-pixel 12-bit coarse ADC and an external 8-bit DAC based fine ADC.
The proposed DROIC uses layout techniques that make it immune to radiation up to
300krad(Si) of total ionizing dose(TID) and single event latch-up(SEL). It also has a
wide input current range from 10pA to 1uA and supports detectors operating from
Short-wave infrared (SWIR) to longwave infrared (LWIR) regions.
ing systems. Performance of ROICs affect the quality of images obtained from IR
imaging systems. Contemporary infrared imaging applications demand ROICs that
can support large dynamic range, high frame rate, high output data rate, at low
cost, size and power. Some of these applications are military surveillance, remote
sensing in space and earth science missions and medical diagnosis. This work focuses
on developing a ROIC unit cell prototype for National Aeronautics and Space Ad
ministration(NASA), Jet Propulsion Laboratory’s(JPL’s) space applications. These
space applications also demand high sensitivity, longer integration times(large well
capacity), wide operating temperature range, wide input current range and immunity
to radiation events such as Single Event Latchup(SEL).
This work proposes a digital ROIC(DROIC) unit cell prototype of 30ux30u size,
to be used mainly with NASA JPL’s High Operating Temperature Barrier Infrared
Detectors(HOT BIRDs). Current state of the art DROICs achieve a dynamic range
of 16 bits using advanced 65-90nm CMOS processes which adds a lot of cost overhead.
The DROIC pixel proposed in this work uses a low cost 180nm CMOS process and
supports a dynamic range of 20 bits operating at a low frame rate of 100 frames per
second(fps), and a dynamic range of 12 bits operating at a high frame rate of 5kfps.
The total electron well capacity of this DROIC pixel is 1.27 billion electrons, enabling
integration times as long as 10ms, to achieve better dynamic range. The DROIC unit
cell uses an in-pixel 12-bit coarse ADC and an external 8-bit DAC based fine ADC.
The proposed DROIC uses layout techniques that make it immune to radiation up to
300krad(Si) of total ionizing dose(TID) and single event latch-up(SEL). It also has a
wide input current range from 10pA to 1uA and supports detectors operating from
Short-wave infrared (SWIR) to longwave infrared (LWIR) regions.
ContributorsPraveen, Subramanya Chilukuri (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Long, Yu (Committee member) / Arizona State University (Publisher)
Created2019
Description
Point of Load (POL) DC-DC converters are increasingly used in space applications, data centres, electric vehicles, portable computers and devices and medical electronics. Heavy computing and processing capabilities of the modern devices have ushered the use of higher battery supply voltage to increase power storage. The need to address this consumer experience driven requirement has propelled the evolution of the next generation of small form-factor power converters which can operate with higher step down ratios while supplying heavy continuous load currents without sacrificing efficiency. Constant On-Time (COT) converter topology is capable of achieving stable operation at high conversion ratio with minimum off-chip components and small silicon area. This work proposes a Constant On-Time buck dc-dc converter for a wide dynamic input range and load currents from 100mA to 10A. Accuracy of this ripple based converter is improved by a unique voltage positioning technique which modulates the reference voltage to lower the average ripple profile close to the nominal output. Adaptive On-time block features a transient enhancement scheme to assist in faster voltage droop recovery when the output voltage dips below a defined threshold. UtilizingGallium Nitride (GaN) power switches enable the proposed converter to achieve very high efficiency while using smaller size inductor-capacitor (LC) power-stage. Use of novel Superjunction devices with higher drain-source blocking voltage simplifies the complex driver design and enables faster frequency of operation. It allows 1.8VComplementary Metal-Oxide Semiconductor (CMOS) devices to effectively drive GaNpower FETs which require 5V gate signal swing. The presented controller circuit uses internal ripple generation which reduces reliance on output cap equivalent series resistance (ESR) for loop stability and facilitates ripples reduction at the output. The ripple generation network is designed to provide ai
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
ContributorsJoshi, Omkar (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Long, Yu (Committee member) / Arizona State University (Publisher)
Created2019
Description
This work focuses on the analysis and design of large-scale millimeter-wave andterahertz (mmWave/THz) beamforming apertures (e.g., reconfigurable reflective surfaces–
RRSs). As such, the small wavelengths and ample bandwidths of these frequencies enable
the development of high-spatial-resolution imaging and high-throughput wireless
communication systems that leverage electrically large apertures to form high-gain
steerable beams.
For the rigorous evaluation of these systems’ performance in realistic application
scenarios, full-wave simulations are needed to capture all the exhibited electromagnetic
phenomena. However, the small wavelengths of mmWave/THz bands lead to enormous
meshes in conventional full-wave simulators. Thus, a novel numerical decomposition
technique is presented, which decomposes the full-wave models in smaller domains with
less meshed elements, enabling their computationally efficient analysis. Thereafter, this
method is leveraged to study a novel radar configuration that employs a rotating linear
antenna with beam steering capabilities to form 3D images. This imaging process requires
fewer elements to carry out high-spatial-resolution imaging compared to traditional 2D
phased arrays, constituting a perfect candidate in low-profile, low-cost applications.
Afterward, a high-yield nanofabrication technique for mmWave/THz graphene
switches is presented. The measured graphene sheet impedances are incorporated into
equivalent circuit models of coplanar switches to identify the optimum mmWave/THz
switch topology that would enable the development of large-scale RRSs.ii
Thereon, the process of integrating the optimized graphene switches into largescale mmWave/THz RRSs is detailed. The resulting RRSs enable dynamic beam steering
achieving 4-bits of phase quantization –for the first time in the known literature–
eliminating the parasitic lobes and increasing the aperture efficiency. Furthermore, the
devised multi-bit configurations use a single switch-per-bit topology retaining low system
complexity and RF losses. Finally, single-bit RRSs are modified to offer single-lobe
patterns by employing a surface randomization technique. This approach allows for the use
of low-complexity single-bit configurations to suppress the undesired quantization lobes
without residing to the use of sophisticated multi-bit topologies.
The presented concepts pave the road toward the implementation and proliferation
of large-scale reconfigurable beamforming apertures that can serve both as mmWave/THz
imagers and as relays or base stations in future wireless communication applications.
ContributorsTheofanopoulos, Panagiotis (Author) / Trichopoulos, Georgios (Thesis advisor) / Balanis, Constantine (Committee member) / Aberle, James (Committee member) / Bliss, Dan (Committee member) / Groppi, Christopher (Committee member) / Arizona State University (Publisher)
Created2021