Matching Items (4)
Filtering by
- All Subjects: Leaching
- All Subjects: nanotechnology
- Member of: ASU Electronic Theses and Dissertations
Description
With the application of reverse osmosis (RO) membranes in the wastewater treatment and seawater desalination, the limitation of flux and fouling problems of RO have gained more attention from researchers. Because of the tunable structure and physicochemical properties of nanomaterials, it is a suitable material that can be used to incorporate with RO to change the membrane performances. Silver is biocidal, which has been used in a variety of consumer products. Recent studies showed that fabricating silver nanoparticles (AgNPs) on membrane surfaces can mitigate the biofouling problem on the membrane. Studies have shown that Ag released from the membrane in the form of either Ag ions or AgNP will accelerate the antimicrobial activity of the membrane. However, the silver release from the membrane will lower the silver loading on the membrane, which will eventually shorten the antimicrobial activity lifetime of the membrane. Therefore, the silver leaching amount is a crucial parameter that needs to be determined for every type of Ag composite membrane.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
ContributorsHan, Bingru (Author) / Westerhoff, Paul (Thesis advisor) / Perreault, Francois (Committee member) / Sinha, Shahnawaz (Committee member) / Arizona State University (Publisher)
Created2017
Description
The volume of end-of-life photovoltaic (PV) modules is increasing as the global PV market increases, and the global PV waste streams are expected to reach 250,000 metric tons by the end of 2020. If the recycling processes are not in place, there would be 60 million tons of end-of-life PV modules lying in the landfills by 2050, that may not become a not-so-sustainable way of sourcing energy since all PV modules could contain certain amount of toxic substances. Currently in the United States, PV modules are categorized as general waste and can be disposed in landfills. However, potential leaching of toxic chemicals and materials, if any, from broken end-of-life modules may pose health or environmental risks. There is no standard procedure to remove samples from PV modules for chemical toxicity testing in the Toxicity Characteristic Leaching Procedure (TCLP) laboratories as per EPA 1311 standard. The main objective of this thesis is to develop an unbiased sampling approach for the TCLP testing of PV modules. The TCLP testing was concentrated only for the laminate part of the modules, as they are already existing recycling technologies for the frame and junction box components of PV modules. Four different sample removal methods have been applied to the laminates of five different module manufacturers: coring approach, cell-cut approach, strip-cut approach, and hybrid approach. These removed samples were sent to two different TCLP laboratories, and TCLP results were tested for repeatability within a lab and reproducibility between the labs. The pros and cons of each sample removal method have been explored and the influence of sample removal methods on the variability of TCLP results has been discussed. To reduce the variability of TCLP results to an acceptable level, additional improvements in the coring approach, the best of the four tested options, are still needed.
ContributorsLeslie, Joswin (Author) / Tamizhmani, Govindasamy (Thesis advisor) / Srinivasan, Devarajan (Committee member) / Kuitche, Joseph (Committee member) / Arizona State University (Publisher)
Created2018
Description
Engineered nanomaterials (ENMs) are added to numerous consumer products to enhance their effectiveness, whether it be for environmental remediation, mechanical properties, or as dietary supplements. Uses of ENMs include adding to enhance products, carbon for strength or dielectric properties, silver for antimicrobial properties, zinc oxide for UV sun-blocking properties, titanium dioxide for photocatalysis, or silica for desiccant properties. However, concerns arise from ENM functional properties that can impact the environment and a lack of regulation regarding ENMs leads to potential public exposure to ENMs and results in ill-informed public or manufacturer perceptions of ENMs. My dissertation evaluates the environmental, human health, and societal impacts of using ENMs, with a focus on ionic silver and nanosilver, in consumer and industrial products. Reproducible experiments served as functional assays to assess ENM distributions among various environmental matrices. Functional assay results were visualized using radar plots and aid in a framework to estimate likely ENM disposition in the environment. To assess beneficial uses of ENMs, bromide ion removal from drinking waters to limit disinfection by-product formation was studied. Silver-enabled graphene oxide materials were capable of removing bromide from water, and exhibited less competition from background solutes (e.g. natural organic matter) when compared against solely ionic silver addition to water for bromide removal. To assess complex interactions of ENMs with the microbiome, batch experiments were performed using fecal samples spiked with ionic silver or commercial dietary silver nanoparticles. Dietary nanosilver and ionic silver exposures to the fecal microbiome for 24 hours reduce short chain fatty acid (SCFA) production and changes the relative abundance of the microbiota. To understand the social perceptions of ENMS, statistically rigorous surveys were conducted to assess related perceptions related to the use of ENMs in drinking water treatment devices the general public and, separately, industrial manufacturers. These stakeholders are influenced by costs and efficiency of the technologies, consumer concerns of the safety of technologies, and environmental health and safety of the technologies. This dissertation represents novel research that took an interdisciplinary approach, spanning from wet-lab engineering bench scale testing to social science survey assessments to better understand the environmental, human health, and societal impacts of using ENMs such as nanosilver and ionic silver in industrial processes and consumer products.
ContributorsKidd, Justin (Author) / Westerhoff, Paul (Thesis advisor) / Krajmalnik-Brown, Rosa (Committee member) / Perreault, Francois (Committee member) / Maynard, Andrew (Committee member) / Arizona State University (Publisher)
Created2020
Description
This dissertation focuses on the structure-function relationships of nanomaterials (NMs) and some of their applications in environmental engineering. The aim is to investigate NMs of different surface chemistries and assess their interactions with biological models, evaluate the weathering impact and degradation parameters to improve polymer coatings, test their efficiency for contaminant removal and provide further understanding in the safe design of nanomaterials. Nanoecotoxicological risk assessment currently suffers from a lack of testing procedures adapted to nanomaterials. Graphene oxide (GO) is a carbon nanomaterial (CNM) that consists of a single layer of carbon atoms arranged in a hexagonal network. It is decorated with a high density of oxygen functional groups including epoxide and hydroxyl moieties on the basal planes and carboxylic and carbonyl groups at the edges. The changes in surface chemistry give GO unique properties that can be tailored for a function. Additionally, because of its simple synthesis and flexible chemistry, GO has been a popular building block of many composite CNMs. In environmental engineering, specifically, water treatment, GO has been studied by itself or as a composite for pollutant removal, biofouling reduction, and as an antimicrobial agent, just to name a few. Like GO, silver (Ag) is another NM widely used in water treatment for its biocidal properties. Despite the recent growth in this field, a fundamental understanding of the function-structure relationships in NMs is still progressing. Through a systematic set of experiments, the structure-properties-function and structure-properties-hazard relationships were investigated. These relationships can be used to establish guidelines to engineer “safe-by-design” functional nanomaterials, where materials are tailored to enhance their function while minimizing their inherent biological or environmental hazard.
ContributorsBarrios, Ana Cecilia (Author) / Perreault, Francois (Thesis advisor) / Abbaszadegan, Morteza (Committee member) / Conroy-Ben, Otakuye (Committee member) / Hua-Wang, Qing (Committee member) / Arizona State University (Publisher)
Created2021