Matching Items (8)
Filtering by
- All Subjects: Materials Science
- All Subjects: Lithium
- Member of: Theses and Dissertations
Description
In this dissertation, combined photo-induced and thermionic electron emission from low work function diamond films is studied through low energy electron spectroscopy analysis and other associated techniques. Nitrogen-doped, hydrogen-terminated diamond films prepared by the microwave plasma chemical vapor deposition method have been the most focused material. The theme of this research is represented by four interrelated issues. (1) An in-depth study describes combined photo-induced and thermionic emission from nitrogen-doped diamond films on molybdenum substrates, which were illuminated with visible light photons, and the electron emission spectra were recorded as a function of temperature. The diamond films displayed significant emissivity with a low work function of ~ 1.5 eV. The results indicate that these diamond emitters can be applied in combined solar and thermal energy conversion. (2) The nitrogen-doped diamond was further investigated to understand the physical mechanism and material-related properties that enable the combined electron emission. Through analysis of the spectroscopy, optical absorbance and photoelectron microscopy results from sample sets prepared with different configurations, it was deduced that the photo-induced electron generation involves both the ultra-nanocrystalline diamond and the interface between the diamond film and metal substrate. (3) Based on results from the first two studies, possible photon-enhanced thermionic emission was examined from nitrogen-doped diamond films deposited on silicon substrates, which could provide the basis for a novel approach for concentrated solar energy conversion. A significant increase of emission intensity was observed at elevated temperatures, which was analyzed using computer-based modeling and a combination of different emission mechanisms. (4) In addition, the electronic structure of vanadium-oxide-terminated diamond surfaces was studied through in-situ photoemission spectroscopy. Thin layers of vanadium were deposited on oxygen-terminated diamond surfaces which led to oxide formation. After thermal annealing, a negative electron affinity was found on boron-doped diamond, while a positive electron affinity was found on nitrogen-doped diamond. A model based on the barrier at the diamond-oxide interface was employed to analyze the results. Based on results of this dissertation, applications of diamond-based energy conversion devices for combined solar- and thermal energy conversion are proposed.
ContributorsSun, Tianyin (Author) / Nemanich, Robert (Thesis advisor) / Ponce, Fernando (Committee member) / Peng, Xihong (Committee member) / Spence, John (Committee member) / Treacy, Michael (Committee member) / Arizona State University (Publisher)
Created2013
Description
Gas diffusion layers (GDLs) are a critical and essential part of proton exchange membrane fuel cells (PEMFCs). They carry out various important functions such as transportation of reactants to and from the reaction sites. The material properties and structural characteristics of the substrate and the microporous layer strongly influence fuel cell performance. The microporous layer of the GDLs was fabricated with the carbon slurry dispersed in water containing ammonium lauryl sulfate (ALS) using the wire rod coating method. GDLs were fabricated with different materials to compose the microporous layer and evaluated the effects on PEMFC power output performance. The consistency of the carbon slurry was achieved by adding 25 wt. % of PTFE, a binding agent with a 75:25 ratio of carbon (Pureblack and vapor grown carbon fiber). The GDLs were investigated in PEMFC under various relative humidity (RH) conditions using H2/O2 and H2/Air. GDLs were also fabricated with the carbon slurry dispersed in water containing sodium dodecyl sulfate (SDS) and multiwalled carbon nanotubes (MWCNTs) with isopropyl alcohol (IPA) based for fuel cell performance comparison. MWCNTs and SDS exhibits the highest performance at 60% and 70% RH with a peak power density of 1100 mW.cm-2 and 850 mW.cm-2 using air and oxygen as an oxidant. This means that the gas diffusion characteristics of these two samples were optimum at 60 and 70 % RH with high limiting current density range. It was also found that the composition of the carbon slurry, specifically ALS concentration has the highest peak power density of 1300 and 500mW.cm-2 for both H2/O2 and H2/Air at 100% RH. However, SDS and MWCNTs demonstrates the lowest power density using air and oxygen as an oxidants at 100% RH.
ContributorsVillacorta, Rashida (Author) / Madakannan, Arunachalanadar (Thesis advisor) / Peng, Xihong (Committee member) / Tamizhmani, Govindasamy (Committee member) / Arizona State University (Publisher)
Created2012
Description
Nanoscale semiconductors with their unique properties and potential applications have been a focus of extensive research in recent years. There are many ways in which semiconductors change the world with computers, cell phones, and solar panels, and nanoscale semiconductors having a promising potential to expand the efficiency, reduce the cost, and improve the flexibility and durability of their design. In this study, theoretical quantum mechanical simulations were performed on several different nanoscale semiconductor materials, including graphene/phosphorene nanoribbons and group III-V nanowires. First principles density functional theory (DFT) was used to study the electronic and structural properties of these nanomaterials in their fully relaxed and strained states. The electronic band gap, effective masses of charge carriers, electronic orbitals, and density of states were most commonly examined with strain, both from intrinsic and external sources. For example, armchair graphene nanoribbons (AGNR) were found to have unprecedented band gap-strain dependence. Phosphorene nanoribbons (PNRs) demonstrate a different behavior, including a chemical scissors effect, and studies revealed a strong relationship between passivation species and band gap tunability. Unlike the super mechanical flexibility of AGNRs and PNRs which can sustain incredible strain, modest yet large strain was applied to group III-V nanowires such as GaAs/InAs. The calculations showed that a direct and indirect band gap transition occurs at some critical strains and the origination of these gap transitions were explored in detail. In addition to the pure nanowires, GaAs/InAs core/shell heterostructure nanowires were also studied. Due to the lattice mismatch between GaAs and InAs, the intrinsic strain in the core/shell nanowires demonstrates an interesting behavior on tuning the electronic properties. This interesting behavior suggests a mechanical way to exert compressive strain on nanowires experimentally, and can create a finite quantum confinement effect on the core.
ContributorsCopple, Andrew (Author) / Peng, Xihong (Thesis advisor) / Chan, Candace (Committee member) / Chizmeshya, Andrew (Committee member) / Ponce, Fernando (Committee member) / Arizona State University (Publisher)
Created2016
Description
Lithium ion batteries are quintessential components of modern life. They are used to power smart devices — phones, tablets, laptops, and are rapidly becoming major elements in the automotive industry. Demand projections for lithium are skyrocketing with production struggling to keep up pace. This drive is due mostly to the rapid adoption of electric vehicles; sales of electric vehicles in 2020 are more than double what they were only a year prior. With such staggering growth it is important to understand how lithium is sourced and what that means for the environment. Will production even be capable of meeting the demand as more industries make use of this valuable element? How will the environmental impact of lithium affect growth? This thesis attempts to answer these questions as the world looks to a decade of rapid growth for lithium ion batteries.
ContributorsMelton, John (Author) / Brian, Jennifer (Thesis director) / Karwat, Darshawn (Committee member) / Chemical Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2021-05
Description
The project goal is aimed to research the most pressing issues facing the lithium supply chain today. It then is tasked with charting a path into the future through strategic recommendations that will help reduce risk, and make a greener, cleaner, and more ethical supply chain.
ContributorsLeeson, Van (Author) / Kelman, Jonathan (Thesis director) / Wiedmer, Robert (Committee member) / Barrett, The Honors College (Contributor) / School of Sustainability (Contributor) / Department of Supply Chain Management (Contributor)
Created2022-05
Description
The fuel cell is a promising device that converts the chemical energy directly into the electrical energy without combustion process. However, the slow reaction rate of the oxygen reduction reaction (ORR) necessitates the development of cathode catalysts for low-temperature fuel cells. After a thorough literature review in Chapter 1, the thesis is divided into three parts as given below in Chapters 2-4.
Chapter 2 describes the study on the Pt and Pt-Me (Me: Co, Ni) alloy nanoparticles supported on the pyrolyzed zeolitic imidazolate framework (ZIF) towards ORR. The Co-ZIF and NiCo-ZIF were synthesized by the solvothermal method and then mixed with Pt precursor. After pyrolysis and acid leaching, the PtCo/NC and PtNiCo/NC were evaluated in proton exchange membrane fuel cells (PEMFC). The peak power density exhibited > 10% and 15% for PtCo/NC and PtNiCo/NC, respectively, compared to that with commercial Pt/C catalyst under identical test conditions.
Chapter 3 is the investigation of the oxygen vacancy (OV) effect in a-MnO2 as a cathode catalyst for alkaline membrane fuel cells (AMFC). The a-MnO2 nanorods were synthesized by hydrothermal method and heated at 300, 400 and 500 ℃ in the air to introduce the OV. The 400 ℃ treated material showed the best ORR performance among all other samples due to more OV in pure a-MnO2 phase. The optimized AMFC electrode showed ~ 45 mW.cm-2, which was slightly lower than that with commercial Pt/C (~60 mW.cm-2).
Chapter 4 is the density functional theory (DFT) study of the protonation effect and active sites towards ORR on a-MnO2 (211) plane. The theoretically optimized oxygen adsorption and hydroxyl ion desorption energies were ~ 1.55-1.95 eV and ~ 0.98-1.45 eV, respectively, by Nørskov et al.’s calculations. All the configurations showed oxygen adsorption and hydroxyl ion desorption energies were ranging from 0.27 to 1.76 eV and 1.59 to 15.0 eV, respectively. The site which was close to two Mn ions showed the best oxygen adsorption and hydroxyl ion desorption energies improvement with the surface protonation.
Based on the results given in Chapters 1-4, the major findings are summarized in Chapter 5.
Chapter 2 describes the study on the Pt and Pt-Me (Me: Co, Ni) alloy nanoparticles supported on the pyrolyzed zeolitic imidazolate framework (ZIF) towards ORR. The Co-ZIF and NiCo-ZIF were synthesized by the solvothermal method and then mixed with Pt precursor. After pyrolysis and acid leaching, the PtCo/NC and PtNiCo/NC were evaluated in proton exchange membrane fuel cells (PEMFC). The peak power density exhibited > 10% and 15% for PtCo/NC and PtNiCo/NC, respectively, compared to that with commercial Pt/C catalyst under identical test conditions.
Chapter 3 is the investigation of the oxygen vacancy (OV) effect in a-MnO2 as a cathode catalyst for alkaline membrane fuel cells (AMFC). The a-MnO2 nanorods were synthesized by hydrothermal method and heated at 300, 400 and 500 ℃ in the air to introduce the OV. The 400 ℃ treated material showed the best ORR performance among all other samples due to more OV in pure a-MnO2 phase. The optimized AMFC electrode showed ~ 45 mW.cm-2, which was slightly lower than that with commercial Pt/C (~60 mW.cm-2).
Chapter 4 is the density functional theory (DFT) study of the protonation effect and active sites towards ORR on a-MnO2 (211) plane. The theoretically optimized oxygen adsorption and hydroxyl ion desorption energies were ~ 1.55-1.95 eV and ~ 0.98-1.45 eV, respectively, by Nørskov et al.’s calculations. All the configurations showed oxygen adsorption and hydroxyl ion desorption energies were ranging from 0.27 to 1.76 eV and 1.59 to 15.0 eV, respectively. The site which was close to two Mn ions showed the best oxygen adsorption and hydroxyl ion desorption energies improvement with the surface protonation.
Based on the results given in Chapters 1-4, the major findings are summarized in Chapter 5.
ContributorsShi, Xuan, Ph.D (Author) / Kannan, Arunachalanadar Mada (Thesis advisor) / Liu, Jingyue (Committee member) / Nam, Changho (Committee member) / Peng, Xihong (Committee member) / Arizona State University (Publisher)
Created2019
Description
Current Li-ion battery technologies are limited by the low capacities of theelectrode materials and require developments to meet stringent performance demands for
future energy storage devices. Electrode materials that alloy with Li, such as Si, are one
of the most promising alternatives for Li-ion battery anodes due to their high capacities.
Tetrel (Si, Ge, Sn) clathrates are a class of host-guest crystalline structures in which
Tetrel elements form a cage framework and encapsulate metal guest atoms. These
structures can form with defects such as framework/guest atom substitutions and
vacancies which result in a wide design space for tuning materials properties. The goal of
this work is to establish structure property relationships within the context of Li-ion
battery anode applications. The type I Ba 8 Al y Ge 46-y clathrates are investigated for their
electrochemical reactions with Li and show high capacities indicative of alloying
reactions. DFT calculations show that Li insertion into the framework vacancies is
favorable, but the migration barriers are too high for room temperature diffusion. Then,
guest free type I clathrates are investigated for their Li and Na migration barriers. The
results show that Li migration in the clathrate frameworks have low energy barriers (0.1-
0.4 eV) which suggest the possibility for room temperature diffusion. Then, the guest
free, type II Si clathrate (Na 1 Si 136 ) is synthesized and reversible Li insertion into the type
II Si clathrate structure is demonstrated. Based on the reasonable capacity (230 mAh/g),
low reaction voltage (0.30 V) and low volume expansion (0.21 %), the Si clathrate could
be a promising insertion anode for Li-ion batteries. Next, synchrotron X-ray
measurements and pair distribution function (PDF) analysis are used to investigate the
lithiation pathways of Ba 8 Ge 43 , Ba 8 Al 16 Ge 30 , Ba 8 Ga 15 Sn 31 and Na 0.3 Si 136 . The results
show that the Ba-clathrates undergo amorphous phase transformations which is distinct
from their elemental analogues (Ge, Sn) which feature crystalline lithiation pathways.
Based on the high capacities and solid-solution reaction mechanism, guest-filled
clathrates could be promising precursors to form alloying anodes with novel
electrochemical properties. Finally, several high temperature (300-550 °C)
electrochemical synthesis methods for Na-Si and Na-Ge clathrates are demonstrated in a
cell using a Na β’’-alumina solid electrolyte.
ContributorsDopilka, Andrew (Author) / Chan, Candace K (Thesis advisor) / Zhuang, Houlong (Committee member) / Peng, Xihong (Committee member) / Sieradzki, Karl (Committee member) / Arizona State University (Publisher)
Created2021
Description
In the present study, primarily, gas diffusion layer samples containing microporous layers (MPLs), are fabricated using carbon paper substrate, PUREBLACK® carbon powder and polyethylene glycol (PEG) as pore forming agent. The GDLs are studied in single cell fuel cell, to evaluate the effect of porosity of the micro-porous layer on the performance at different operating relative humidity conditions and compared with commercial GDLs. Scanning electron microscopy (SEM) and contact angle measurements indicate crack-free surface morphology and hydrophobic characteristics of the PUREBLACK® based GDLs, respectively. By varying the wt. % of PEG, fuel cell performance is evaluated under relative humidity conditions of 60 and 100 % using H2/O2 and H2/Air at 70 oC and the durability is also evaluated for the samples without, with 30% PEG and commercial. The fuel cell performance of the GDL with 30 % PEG (with pore volume 1.72 cc.g-1) exhibited higher performance (444 and 432 mW.cm-2 at 60 and 100 % RH conditions, respectively using H2 and air) compared to that without pore forming agent (436 and 397 mW.cm-2).Subsequently, the best performing configuration underwent two different ex-situ methods of accelerated stress testing (AST), in water and hydrogen peroxide (30%), for 1000 and 24 h, respectively. The samples were evaluated via contact angle, SEM, and fuel cell performance, before and after the ASTs, and compared to similar configuration, using carbon powder VULCAN® (XC-72R), and aged in the exact same conditions. Contact angle and SEM demonstrated greater degradation of VULCAN® carbon, especially in hydrogen peroxide, where carbon corrosion caused surface cracks and change in hydrophobicity. The fuel cell performance and durability, evaluated at 60 and 100% RH at 70 oC, using O2 and air as oxidants, confirmed that VULCAN® carbon is more prone to carbon corrosion, with significant performance loss (12-19%) in contrast to PUREBLACK® that demonstrated higher carbon corrosion resistance due to its graphitized surface.
ContributorsAthanasaki, Grigoria (Author) / Kannan, Arunachala Mada A. M. (Thesis advisor) / Nam, Changho (Committee member) / Peng, Xihong (Committee member) / Arizona State University (Publisher)
Created2021