Matching Items (149)
Filtering by
- All Subjects: Civil Engineering
- Genre: Doctoral Dissertation
- Member of: Theses and Dissertations
Description
This study presents the results of one of the first attempts to characterize the pore water pressure response of soils subjected to traffic loading under saturated and unsaturated conditions. It is widely known that pore water pressure develops within the soil pores as a response to external stimulus. Also, it has been recognized that the development of pores water pressure contributes to the degradation of the resilient modulus of unbound materials. In the last decades several efforts have been directed to model the effect of air and water pore pressures upon resilient modulus. However, none of them consider dynamic variations in pressures but rather are based on equilibrium values corresponding to initial conditions. The measurement of this response is challenging especially in soils under unsaturated conditions. Models are needed not only to overcome testing limitations but also to understand the dynamic behavior of internal pore pressures that under critical conditions may even lead to failure. A testing program was conducted to characterize the pore water pressure response of a low plasticity fine clayey sand subjected to dynamic loading. The bulk stress, initial matric suction and dwelling time parameters were controlled and their effects were analyzed. The results were used to attempt models capable of predicting the accumulated excess pore pressure at any given time during the traffic loading and unloading phases. Important findings regarding the influence of the controlled variables challenge common beliefs. The accumulated excess pore water pressure was found to be higher for unsaturated soil specimens than for saturated soil specimens. The maximum pore water pressure always increased when the high bulk stress level was applied. Higher dwelling time was found to decelerate the accumulation of pore water pressure. In addition, it was found that the higher the dwelling time, the lower the maximum pore water pressure. It was concluded that upon further research, the proposed models may become a powerful tool not only to overcome testing limitations but also to enhance current design practices and to prevent soil failure due to excessive development of pore water pressure.
ContributorsCary, Carlos (Author) / Zapata, Claudia E (Thesis advisor) / Wiczak, Matthew W (Thesis advisor) / Kaloush, Kamil (Committee member) / Sandra, Houston (Committee member) / Arizona State University (Publisher)
Created2011
Description
It is estimated that wind induced soil transports more than 500 x 106 metric tons of fugitive dust annually. Soil erosion has negative effects on human health, the productivity of farms, and the quality of surface waters. A variety of different polymer stabilizers are available on the market for fugitive dust control. Most of these polymer stabilizers are expensive synthetic polymer products. Their adverse effects and expense usually limits their use. Biopolymers provide a potential alternative to synthetic polymers. They can provide dust abatement by encapsulating soil particles and creating a binding network throughout the treated area. This research into the effectiveness of biopolymers for fugitive dust control involved three phases. Phase I included proof of concept tests. Phase II included carrying out the tests in a wind tunnel. Phase III consisted of conducting the experiments in the field. Proof of concept tests showed that biopolymers have the potential to reduce soil erosion and fugitive dust transport. Wind tunnel tests on two candidate biopolymers, xanthan and chitosan, showed that there is a proportional relationship between biopolymer application rates and threshold wind velocities. The wind tunnel tests also showed that xanthan gum is more successful in the field than chitosan. The field tests showed that xanthan gum was effective at controlling soil erosion. However, the chitosan field data was inconsistent with the xanthan data and field data on bare soil.
ContributorsAlsanad, Abdullah (Author) / Kavazanjian, Edward (Thesis advisor) / Edwards, David (Committee member) / Zapata, Claudia (Committee member) / Arizona State University (Publisher)
Created2011
Description
Nowadays there is a pronounced interest in the need for sustainable and reliable infrastructure systems to address the challenges of the future infrastructure development. This dissertation presents the research associated with understanding various sustainable and reliable design alternatives for water distribution systems. Although design of water distribution networks (WDN) is a thoroughly studied area, most researchers seem to focus on developing algorithms to solve the non-linear hard kind of optimization problems associated with WDN design. Cost has been the objective in most of the previous studies with few models considering reliability as a constraint, and even fewer models accounting for the environmental impact of WDN. The research presented in this dissertation combines all these important objectives into a multi-objective optimization framework. The model used in this research is an integration of a genetic algorithm optimization tool with a water network solver, EPANET. The objectives considered for the optimization are Life Cycle Costs (LCC) and Life Cycle Carbon Dioxide (CO2) Emissions (LCE) whereby the system reliability is made a constraint. Three popularly used resilience metrics were investigated in this research for their efficiency in aiding the design of WDNs that are able to handle external natural and man-made shocks. The best performing resilience metric is incorporated into the optimization model as an additional objective. Various scenarios were developed for the design analysis in order to understand the trade-offs between different critical parameters considered in this research. An approach is proposed and illustrated to identify the most sustainable and resilient design alternatives from the solution set obtained by the model employed in this research. The model is demonstrated by using various benchmark networks that were studied previously. The size of the networks ranges from a simple 8-pipe system to a relatively large 2467-pipe one. The results from this research indicate that LCE can be reduced at a reasonable cost when a better design is chosen. Similarly, resilience could also be improved at an additional cost. The model used in this research is more suitable for water distribution networks. However, the methodology could be adapted to other infrastructure systems as well.
ContributorsPiratla, Kalyan Ram (Author) / Ariaratnam, Samuel T (Thesis advisor) / Chasey, Allan (Committee member) / Lueke, Jason (Committee member) / Arizona State University (Publisher)
Created2012
Description
One of the main requirements of designing perpetual pavements is to determine the endurance limit of Hot Mix Asphalt (HMA). The purpose of this study was to validate the endurance limit for HMA using laboratory beam fatigue tests. A mathematical procedure was developed to determine the endurance limit of HMA due to healing that occurs during the rest periods between loading cycles. Relating healing to endurance limit makes this procedure unique compared to previous research projects that investigated these concepts separately. An extensive laboratory testing program, including 468 beam tests, was conducted according to AASHTO T321-03 test procedure. Six factors that affect the fatigue response of HMA were evaluated: binder type, binder content, air voids, test temperature, rest period and applied strain. The endurance limit was determined when no accumulated damage occurred indicating complete healing. Based on the test results, a first generation predictive model was developed to relate stiffness ratio to material properties. A second generation stiffness ratio model was also developed by replacing four factors (binder type, binder content, air voids, and temperature) with the initial stiffness of the mixture, which is a basic material property. The model also accounts for the nonlinear effects of the rest period and the applied strain on the healing and endurance limit. A third generation model was then developed by incorporation the number of loading cycles at different locations along the fatigue degradation curve for each test in order to account for the nonlinearity between stiffness ratio and loading cycles. In addition to predicting endurance limit, the model has the ability to predict the number of cycles to failure at any rest period and stiffness combination. The model was used to predict fatigue relationship curves for tests with rest period and determining the K1, K2, and K3 fatigue cracking coefficients. The three generation models predicted close endurance limit values ranging from 22 to 204 micro strains. After developing the third generation stiffness ratio model, the predicted endurance limit values were integrated in the strain-Nf fatigue relationships as a step toward incorporating the endurance limit in the MEPDG software. The results of this study can be used to design perpetual pavements that can sustain a large number of loads if traffic volumes and vehicle weights are controlled.
ContributorsSouliman, Mena (Author) / Mamlouk, Michael S. (Thesis advisor) / Witczak, Matthew W. (Thesis advisor) / Kaloush, Kamil (Committee member) / Arizona State University (Publisher)
Created2012
Description
The wood-framing trade has not sufficiently been investigated to understand the work task sequencing and coordination among crew members. A new mental framework for a performing crew was developed and tested through four case studies. This framework ensured similar team performance as the one provided by task micro-scheduling in planning software. It also allowed evaluation of the effect of individual coordination within the crew on the crew's productivity. Using design information, a list of micro-activities/tasks and their predecessors was automatically generated for each piece of lumber in the four wood frames. The task precedence was generated by applying elementary geometrical and technological reasoning to each frame. Then, the duration of each task was determined based on observations from videotaped activities. Primavera's (P6) resource leveling rules were used to calculate the sequencing of tasks and the minimum duration of the whole activity for various crew sizes. The results showed quick convergence towards the minimum production time and allowed to use information from Building Information Models (BIM) to automatically establish the optimal crew sizes for frames. Late Start (LS) leveling priority rule gave the shortest duration in every case. However, the logic of LS tasks rule is too complex to be conveyed to the framing crew. Therefore, the new mental framework of a well performing framer was developed and tested to ensure high coordination. This mental framework, based on five simple rules, can be easily taught to the crew and ensures a crew productivity congruent with the one provided by the LS logic. The case studies indicate that once the worst framer in the crew surpasses the limit of 11% deviation from applying the said five rules, every additional percent of deviation reduces the productivity of the whole crew by about 4%.
ContributorsMaghiar, Marcel M (Author) / Wiezel, Avi (Thesis advisor) / Mitropoulos, Panagiotis (Committee member) / Cooke, Nancy J. (Committee member) / Arizona State University (Publisher)
Created2011
Description
The primary objective of this study is to understand the effect of soil cracking on foundation performance for expansive soil profiles. Two major effects of cracks were studied to assess the effect of cracks on foundation performance. First, the effect of cracks on soil volume change response was studied. Second, the effect of cracks on unsaturated flow properties and extent and degree of wetting were evaluated. Multiple oedometer-type pressure plate tests were conducted to evaluate the effect of cracks on soil properties commonly used in volume change (heave) analyses, such as swell pressure, soil water characteristic curve (SWCC), and swell potential. Additionally, the effect of cracks on saturated and unsaturated hydraulic conductivity was studied experimentally to assess the impact of cracks on properties critical to evaluation of extent and degree of wetting. Laboratory experiments were performed on both intact and cracked specimen so that the effect of cracks on behavior could be benchmarked against intact soil response. Based on laboratory observations, the SWCC of a cracked soil is bimodal. However, this bimodal behavior is only observed in the very low suction ranges. Because the bimodal nature of the SWCC of cracked clays is only distinguishable at extremely low suctions, the bimodal behavior is unlikely to have engineering significance when soils remain unsaturated. A "lumped mass" parameter approach has been studied as a practical approach for modeling of cracked soils for both fluid flow and volume change determination. Laboratory unsaturated flow experiments were simulated using a saturated-unsaturated flow finite element code, SVFlux, to back-analyze unsaturated hydraulic conductivity functions for the subject soils. These back-analyzed results were compared to the results from traditionally-applied analyses of the laboratory instantaneous profile tests on intact and cracked specimens. Based on this comparison, empirical adjustments were suggested for modeling "lumped mass" cracked soil behavior in numerical codes for fluid flow through cracked soils. Using the empirically adjusted flow parameters for unsaturated flow modeling, example analyses were performed for slab-on-grade problems to demonstrate the impact of cracks on degree and extent of wetting under unsaturated and saturated flow conditions for different surface flux boundary conditions.
ContributorsAbbaszadeh, Mohammad (Author) / Houston, Sandra L. (Thesis advisor) / Zapata, Claudia E (Thesis advisor) / Welfert, Bruno D (Committee member) / Houston, William N (Committee member) / Arizona State University (Publisher)
Created2011
Description
The development of microsimulation approaches to urban systems modeling has occurred largely in three parallel streams of research, namely, land use, travel demand and traffic assignment. However, there are important dependencies and inter-relationships between the model systems which need to be accounted to accurately and comprehensively model the urban system. Location choices affect household activity-travel behavior, household activity-travel behavior affects network level of service (performance), and network level of service, in turn, affects land use and activity-travel behavior. The development of conceptual designs and operational frameworks that represent such complex inter-relationships in a consistent fashion across behavioral units, geographical entities, and temporal scales has proven to be a formidable challenge. In this research, an integrated microsimulation modeling framework called SimTRAVEL (Simulator of Transport, Routes, Activities, Vehicles, Emissions, and Land) that integrates the component model systems in a behaviorally consistent fashion, is presented. The model system is designed such that the activity-travel behavior model and the dynamic traffic assignment model are able to communicate with one another along continuous time with a view to simulate emergent activity-travel patterns in response to dynamically changing network conditions. The dissertation describes the operational framework, presents the modeling methodologies, and offers an extensive discussion on the advantages that such a framework may provide for analyzing the impacts of severe network disruptions on activity-travel choices. A prototype of the model system is developed and implemented for a portion of the Greater Phoenix metropolitan area in Arizona to demonstrate the capabilities of the model system.
ContributorsKonduri, Karthik Charan (Author) / Pendyala, Ram M. (Thesis advisor) / Ahn, Soyoung (Committee member) / Kuby, Michael (Committee member) / Kaloush, Kamil (Committee member) / Arizona State University (Publisher)
Created2012
Description
This dissertation presents a portable methodology for holistic planning and optimization of right of way infrastructure rehabilitation that was designed to generate monetary savings when compared to planning that only considers single infrastructure components. Holistic right of way infrastructure planning requires simultaneous consideration of the three right of way infrastructure components that are typically owned and operated under the same municipal umbrella: roads, sewer, and water. The traditional paradigm for the planning of right way asset management involves operating in silos where there is little collaboration amongst different utility departments in the planning of maintenance, rehabilitation, and renewal projects. By collaborating across utilities during the planning phase, savings can be achieved when collocated rehabilitation projects from different right of way infrastructure components are synchronized to occur at the same time. These savings are in the form of shared overhead and mobilization costs, and roadway projects providing open space for subsurface utilities. Individual component models and a holistic model that utilize evolutionary algorithms to optimize five year maintenance, rehabilitation, and renewal plans for the road, sewer, and water components were created and compared. The models were designed to be portable so that they could be used with any infrastructure condition rating, deterioration modeling, and criticality assessment systems that might already be in place with a municipality. The models attempt to minimize the overall component score, which is a function of the criticality and condition of the segments within each network, by prescribing asset management activities to different segments within a component network while subject to a constraining budget. The individual models were designed to represent the traditional decision making paradigm and were compared to the holistic model. In testing at three different budget levels, the holistic model outperformed the individual models in the ability to generate five year plans that optimized prescribed maintenance, rehabilitation and renewal for various segments in order to achieve the goal of improving the component score. The methodology also achieved the goal of being portable, in that it is compatible with any condition rating, deterioration, and criticality system.
ContributorsCarey, Brad David (Author) / Lueke, Jason S (Thesis advisor) / Ariaratnam, Samuel (Committee member) / Bashford, Howard (Committee member) / Arizona State University (Publisher)
Created2012
Description
The focus of this study is statistical characterization of the significant duration of strong ground motion time histories. The significant duration is defined as the time needed to build up between five and seventy five (SD575) and ninety five percent (SD595) of the energy of a strong motion record. Energy is measured as the integral of the square of the acceleration time history and can be used to capture the potential destructiveness of an earthquake. Correlations of the geometric means of the two significant duration measures (SD575 and SD595) with source, path, and near surface site parameters have been investigated using the geometric mean of 2,690 pairs of recorded horizontal strong ground motion data from 129 earthquakes in active plate margins. These time histories correspond to moment magnitudes between 4.8 and 7.9, site to source distances up to 200 km, and near surface shear wave velocity ranging from 120 to 2250 m/s. Empirical relationships have been developed based upon the simple functional forms, and observed correlations. The coefficients of the independent variables in these empirical relationships have been determined through nonlinear regression analysis using a random effects model. It is found that significant duration measures correlate well with magnitude, site to source distance, and near surface shear wave velocity. The influence of the depth to top of rupture, depth to the shear wave velocity of 1000 m/s and the style of faulting were not found to be statistically significant. Comparison of the empirical relationship developed in this study with existing empirical relationships for the significant duration shows good agreement at intermediate magnitudes (M 6.5). However, at larger and smaller magnitude, the differences between the correlations developed in this study and those from previous studies are significant.
ContributorsGhanat, Simon T (Author) / Kavazanjian, Jr., Edward (Thesis advisor) / Houston, Sandra (Committee member) / Arrowsmith, Ramon (Committee member) / Arizona State University (Publisher)
Created2011
Description
Increased priority on the minimization of environmental impacts of conventional construction materials in recent years has motivated increased use of waste materials or bi-products such as fly ash, blast furnace slag with a view to reduce or eliminate the manufacturing/consumption of ordinary portland cement (OPC) which accounts for approximately 5-7% of global carbon dioxide emission. The current study explores, for the first time, the possibility of carbonating waste metallic iron powder to develop carbon-negative sustainable binder systems for concrete. The fundamental premise of this work is that metallic iron will react with aqueous CO2 under controlled conditions to form complex iron carbonates which have binding capabilities. The compressive and flexural strengths of the chosen iron-based binder systems increase with carbonation duration and the specimens carbonated for 4 days exhibit mechanical properties that are comparable to those of companion ordinary portland cement systems. The optimal mixture proportion and carbonation regime for this non-conventional sustainable binder is established based on the study of carbonation efficiency of a series of mixtures using thermogravimetric analysis. The pore- and micro-structural features of this novel binding material are also evaluated. The fracture response of this novel binder is evaluated using strain energy release rate and measurement of fracture process zone using digital image correlation (DIC). The iron-based binder system exhibits significantly higher strain energy release rates when compared to those of the OPC systems in both the unreinforced and glass fiber reinforced states. The iron-based binder also exhibits higher amount of area of fracture process zone due to its ability to undergo inelastic deformation facilitated by unreacted metallic iron particle inclusions in the microstructure that helps crack bridging /deflection. The intrinsic nano-mechanical properties of carbonate reaction product are explored using statistical nanoindentation technique coupled with a stochastic deconvolution algorithm. Effect of exposure to high temperature (up to 800°C) is also studied. Iron-based binder shows significantly higher residual flexural strength after exposure to high temperatures. Results of this comprehensive study establish the viability of this binder type for concrete as an environment-friendly and economical alternative to OPC.
ContributorsDas, Sumanta (Author) / Neithalath, Narayanan (Thesis advisor) / Rajan, S.D. (Committee member) / Mobasher, Barzin (Committee member) / Marzke, Robert (Committee member) / Chawla, Nikhilesh (Committee member) / Stone, David (Committee member) / Arizona State University (Publisher)
Created2015