Matching Items (6)
Filtering by
- All Subjects: Civil Engineering
- All Subjects: Leaching
- Member of: Theses and Dissertations
Description
With the application of reverse osmosis (RO) membranes in the wastewater treatment and seawater desalination, the limitation of flux and fouling problems of RO have gained more attention from researchers. Because of the tunable structure and physicochemical properties of nanomaterials, it is a suitable material that can be used to incorporate with RO to change the membrane performances. Silver is biocidal, which has been used in a variety of consumer products. Recent studies showed that fabricating silver nanoparticles (AgNPs) on membrane surfaces can mitigate the biofouling problem on the membrane. Studies have shown that Ag released from the membrane in the form of either Ag ions or AgNP will accelerate the antimicrobial activity of the membrane. However, the silver release from the membrane will lower the silver loading on the membrane, which will eventually shorten the antimicrobial activity lifetime of the membrane. Therefore, the silver leaching amount is a crucial parameter that needs to be determined for every type of Ag composite membrane.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
This study is attempting to compare four different silver leaching test methods, to study the silver leaching potential of the silver impregnated membranes, conducting the advantages and disadvantages of the leaching methods. An In-situ reduction Ag loaded RO membrane was examined in this study. A custom waterjet test was established to create a high-velocity water flow to test the silver leaching from the nanocomposite membrane in a relative extreme environment. The batch leaching test was examined as the most common leaching test method for the silver composite membrane. The cross-flow filtration and dead-end test were also examined to compare the silver leaching amounts.
The silver coated membrane used in this experiment has an initial silver loading of 2.0± 0.51 ug/cm2. The mass balance was conducted for all of the leaching tests. For the batch test, water jet test, and dead-end filtration, the mass balances are all within 100±25%, which is acceptable in this experiment because of the variance of the initial silver loading on the membranes. A bad silver mass balance was observed at cross-flow filtration. Both of AgNP and Ag ions leached in the solution was examined in this experiment. The concentration of total silver leaching into solutions from the four leaching tests are all below the Secondary Drinking Water Standard for silver which is 100 ppb. The cross-flow test is the most aggressive leaching method, which has more than 80% of silver leached from the membrane after 50 hours of the test. The water jet (54 ± 6.9% of silver remaining) can cause higher silver leaching than batch test (85 ± 1.2% of silver remaining) in one-hour, and it can also cause both AgNP and Ag ions leaching from the membrane, which is closer to the leaching condition in the cross-flow test.
ContributorsHan, Bingru (Author) / Westerhoff, Paul (Thesis advisor) / Perreault, Francois (Committee member) / Sinha, Shahnawaz (Committee member) / Arizona State University (Publisher)
Created2017
Description
The volume of end-of-life photovoltaic (PV) modules is increasing as the global PV market increases, and the global PV waste streams are expected to reach 250,000 metric tons by the end of 2020. If the recycling processes are not in place, there would be 60 million tons of end-of-life PV modules lying in the landfills by 2050, that may not become a not-so-sustainable way of sourcing energy since all PV modules could contain certain amount of toxic substances. Currently in the United States, PV modules are categorized as general waste and can be disposed in landfills. However, potential leaching of toxic chemicals and materials, if any, from broken end-of-life modules may pose health or environmental risks. There is no standard procedure to remove samples from PV modules for chemical toxicity testing in the Toxicity Characteristic Leaching Procedure (TCLP) laboratories as per EPA 1311 standard. The main objective of this thesis is to develop an unbiased sampling approach for the TCLP testing of PV modules. The TCLP testing was concentrated only for the laminate part of the modules, as they are already existing recycling technologies for the frame and junction box components of PV modules. Four different sample removal methods have been applied to the laminates of five different module manufacturers: coring approach, cell-cut approach, strip-cut approach, and hybrid approach. These removed samples were sent to two different TCLP laboratories, and TCLP results were tested for repeatability within a lab and reproducibility between the labs. The pros and cons of each sample removal method have been explored and the influence of sample removal methods on the variability of TCLP results has been discussed. To reduce the variability of TCLP results to an acceptable level, additional improvements in the coring approach, the best of the four tested options, are still needed.
ContributorsLeslie, Joswin (Author) / Tamizhmani, Govindasamy (Thesis advisor) / Srinivasan, Devarajan (Committee member) / Kuitche, Joseph (Committee member) / Arizona State University (Publisher)
Created2018
Description
Electrospinning is a means of fabricating micron-scale diameter fiber networks with enmeshed nanomaterials. Polymeric nanocomposites for water treatment require the manipulation of fiber morphology to expose nanomaterial surface area while anchoring the nanomaterials and maintaining fiber integrity; that is the overarching goal of this dissertation. The first investigation studied the effect of metal oxide nanomaterial loadings on electrospinning process parameters such as critical voltage, viscosity, fiber diameter, and nanomaterial distribution. Increases in nanomaterial loading below 5% (w/v) were not found to affect critical voltage or fiber diameter. Nanomaterial dispersion was conserved throughout the process. Arsenic adsorption tests determined that the fibers were non-porous. Next, the morphologies of fibers made with carbonaceous materials and the effect of final fiber assembly on adsorption kinetics of a model organic contaminant (phenanthrene, PNT) was investigated. Superfine powdered activated carbon (SPAC), C60 fullerenes, multi-walled carbon nanotubes, and graphene platelets were added to PS and electrospun. SPAC maintained its internal pore structure and created porous fibers which had 30% greater PNT sorption than PS alone and a sevenfold increase in surface area. Carbon-based nanomaterial-PS fibers were thicker but less capacious than neat polystyrene electrospun fibers. The surface areas of the carbonaceous nanomaterial-polystyrene composites decreased compared to neat PS, and PNT adsorption experiments yielded decreased capacity for two out of three carbonaceous nanomaterials. Finally, the morphology and arsenic adsorption capacity of a porous TiO2-PS porous fiber was investigated. Porous fiber was made using polyvinylpyrrolidone (PVP) as a porogen. PVP, PS, and TiO2 were co-spun and the PVP was subsequently eliminated, leaving behind a porous fiber morphology which increased the surface area of the fiber sevenfold and exposed the nanoscale TiO2 enmeshed inside the PS. TiO2-PS fibers had comparable arsenic adsorption performance to non-embedded TiO2 despite containing less TiO2 mass. The use of a sacrificial polymer as a porogen facilitates the creation of a fiber morphology which provides access points between the target pollutant in an aqueous matrix and the sorptive nanomaterials enmeshed inside the fiber while anchoring the nanomaterials, thus preventing release.
ContributorsHoogesteijn von Reitzenstein, Natalia Virginia (Author) / Westerhoff, Paul (Thesis advisor) / Hristovski, Kiril (Committee member) / Perreault, Francois (Committee member) / Herckes, Pierre (Committee member) / Arizona State University (Publisher)
Created2018
Description
Glasses have many applications such as containers, substrates of displays, high strength fibers and portable electronic display panels. Their excellent mechanical properties such as high hardness, good forming ability and scratch resistance make glasses ideal for these applications. Many factors affect the selection of one glass over another for a given purpose such as cost, ingredients, scalability of manufacturing, etc. Typically, silicate based glasses are often selected because they satisfy most of the selection criteria. However, with the recent abundant use of these glasses in touch-based applications, understanding their abilities to dissipate energy due to surface contact loads has become increasingly desirable. The most common silicate glasses worldwide are glassy silica and soda lime. Calcium aluminosilicates are also gaining popularity due to their importance as substrates for display screens in electronic devices. The surface energy dissipation and strength of these glasses are based on several factors, but predominantly rely on ingredient composition and the so-called Indentation Size Effect (ISE), where the strength depends on the maximum surface force. Both the composition and ISE alter the strength and favored energy dissipation mechanisms of the glass. Unlocking the contribution of these mechanisms and elucidating their dependence on composition and force is the underlining goal of this thesis.Prior to cracking, silicate glasses can inelastically deform by shear and densification. However, the link between the mechanical properties, strength, glass structure and maximum force and the propensity by which either of these mechanisms are favored still remains unclear. In this study, the first aim is to elucidate the causes of the ISE and
i
explore the relationships between the ISE and the dissipation mechanisms, and identify what feature(s) of the glass can be used to infer their behavior. All glasses have shown a strong link between the ISE and shear flow and densification. Second, the link between composition and the dissipation mechanisms will be elucidated. This is accomplished by performing indentation tests coupled with an annealing method to independently quantify the amount of volume associated with each dissipation mechanism and elucidate relationships with ingredients and structure of the glasses. Some conclusions will then be presented that link all these behaviors together.
ContributorsKazembeyki, Maryam (Author) / Hoover, Christian G (Thesis advisor) / Rajan, Subramaniam (Committee member) / Neithalath, Narayanan (Committee member) / Chawla, Nikhilesh (Committee member) / Perreault, Francois (Committee member) / Arizona State University (Publisher)
Created2021
Description
This dissertation investigates the mechanisms that lead to fouling, as well as how an understanding of how these mechanisms can be leveraged to mitigate fouling.
To limit fouling on feed spacers, various coatings were applied. The results showed silver-coated biocidal spacers outperformed other spacers by all measures. The control polypropylene spacers performed in-line with, or better than, the other coatings. Polypropylene’s relative anti-adhesiveness is due to its surface free energy (SFE; 30.0 +/- 2.8 mN/m), which, according to previously generated models, is near the ideal SFE for resisting adhesion of bacteria and organics (~25 mN/m).
Previous research has indicated that electrochemical surfaces can be used to remove biofilms. To better elucidate the conditions and kinetics of biofilm removal, optical coherence tomography microscopy was used to visualize the biofouling and subsequent cleaning of the surface. The 50.0 mA cm-2 and 87.5 mA cm-2 current densities proved most effective in removing the biofilm. The 50.0 mA cm-2 condition offers the best balance between performance and energy use for anodic operation.
To test the potential to incorporate electrochemical coatings into infrastructure, membranes were coated with carbon nanotubes (CNTs), rendering the membranes electrochemically active. These membranes were biofouled and subsequently cleaned via electrochemical reactions. P. aeruginosa was given 72h to develop a biofilm on the CNT-coated membranes in a synthetic medium simulating desalination brines. Cathodic reactions, which generate H2 gas, produce vigorous bubbling at a current density of 12.5 mA cm-2 and higher, leading to a rapid and complete displacement of the biofilm from the CNT-functionalized membrane surface. In comparison, anodic reactions were unable to disperse the biofilms from the surface at similar current densities.
The scaling behavior of a nanophotonics-enabled solar membrane distillation (NESMD) system was investigated. The results showed the NESMD system to be resistant to scaling. The system operated without any decline in flux up to concentrations 6x higher than the initial salt concentration (8,439 mg/L), whereas in traditional membrane distillation (MD), flux essentially stopped at a salt concentration factor of 2x. Microscope and analytical analyses showed more fouling on the membranes from the MD system.
To limit fouling on feed spacers, various coatings were applied. The results showed silver-coated biocidal spacers outperformed other spacers by all measures. The control polypropylene spacers performed in-line with, or better than, the other coatings. Polypropylene’s relative anti-adhesiveness is due to its surface free energy (SFE; 30.0 +/- 2.8 mN/m), which, according to previously generated models, is near the ideal SFE for resisting adhesion of bacteria and organics (~25 mN/m).
Previous research has indicated that electrochemical surfaces can be used to remove biofilms. To better elucidate the conditions and kinetics of biofilm removal, optical coherence tomography microscopy was used to visualize the biofouling and subsequent cleaning of the surface. The 50.0 mA cm-2 and 87.5 mA cm-2 current densities proved most effective in removing the biofilm. The 50.0 mA cm-2 condition offers the best balance between performance and energy use for anodic operation.
To test the potential to incorporate electrochemical coatings into infrastructure, membranes were coated with carbon nanotubes (CNTs), rendering the membranes electrochemically active. These membranes were biofouled and subsequently cleaned via electrochemical reactions. P. aeruginosa was given 72h to develop a biofilm on the CNT-coated membranes in a synthetic medium simulating desalination brines. Cathodic reactions, which generate H2 gas, produce vigorous bubbling at a current density of 12.5 mA cm-2 and higher, leading to a rapid and complete displacement of the biofilm from the CNT-functionalized membrane surface. In comparison, anodic reactions were unable to disperse the biofilms from the surface at similar current densities.
The scaling behavior of a nanophotonics-enabled solar membrane distillation (NESMD) system was investigated. The results showed the NESMD system to be resistant to scaling. The system operated without any decline in flux up to concentrations 6x higher than the initial salt concentration (8,439 mg/L), whereas in traditional membrane distillation (MD), flux essentially stopped at a salt concentration factor of 2x. Microscope and analytical analyses showed more fouling on the membranes from the MD system.
ContributorsRice, Douglas, Ph.D (Author) / Perreault, Francois (Thesis advisor) / Abbaszadegan, Morteza (Committee member) / Fox, Peter (Committee member) / Lind-Thomas, Mary Laura (Committee member) / Arizona State University (Publisher)
Created2019
Description
Iodine and silver ions (Ag+), added as silver fluoride (AgF) or silver nitrate (AgNO3), are currently being used as a biocide to control the spread of bacteria in the water storage tanks of the International Space Station (ISS). Due to the complications of the iodine system, NASA is interested to completely replace iodine with silver and apply it as an antibacterial surface coating on stainless steel (SS) surfaces for biofouling control in extended space missions. However, Ag+ is highly soluble and rapidly dissolves in water, as a result, the coated surface loses its antibacterial properties. The dissolution of NPs into Ag+ and subsequent solubilization reduces its effectivity or extended period application. This study focuses on the in-situ nucleation of silver nanoparticles (AgNP) on stainless steel followed by their partial passivation by the formation of a low solubility silver sulfide (Ag2S), silver bromide (AgBr), and silver iodide (AgI) shell with various concentrations for an increased long-term biofouling performance and a slower silver release over time. Antibacterial activity was evaluated using Pseudomonas aeruginosa. The highest bacterial inactivation (up to 75%) occurred with sulfidized AgNPs as opposed to bromidized (up to 50%) and iodized NPs (up to 60%). Surface analysis by scanning electron microscopy (SEM) showed considerably fewer particles on AgBr and AgI compared to Ag2S-coated samples. Silver iodide was not tested in additional experiments due to its drawbacks and its poor antibacterial performance compared to sulfidized samples. Compared to pristine AgNPs, Ag release from both sulfidized and bromidized NPs was significantly low (16% vs 6% or less) depending on the extent of sulfidation or bromidation. Experiments were also carried out to investigate the effect of passivation on biofilm formation. Biofilm growth was smaller on surfaces treated with 10-3 M Na2S and 10-3 M NaBr compared to the surface of pristine AgNPs. Overall, sulfidation appears to be the most effective option to control biofilm formation on stainless steel. However, future research is needed to verify the effectiveness of sulfidized AgNPs on other metals including Inconel 718 and Titanium 6Al-4V used in the spacecraft potable water systems.
ContributorsRanjbari, Kiarash (Author) / Perreault, Francois (Thesis advisor) / Abbaszadegan, Morteza (Committee member) / Islam, Mohammed R (Committee member) / Arizona State University (Publisher)
Created2021