Matching Items (16)
Filtering by
- All Subjects: Aerodynamics
- Creators: Mechanical and Aerospace Engineering Program
- Creators: Baker, Dylan Paul
Description
An understanding of aerodynamics is crucial for automobile performance and efficiency. There are many types of “add-on” aerodynamic devices for cars including wings, splitters, and vortex generators. While these have been studied extensively, rear spoilers have not, and their effects are not as widely known. A Computational Fluid Dynamics (CFD) and wind tunnel study was performed to study the effects of spoilers on vehicle aerodynamics and performance. Vehicle aerodynamics is geometry dependent, meaning what applies to one car may or may not apply on another. So, the Scion FRS was chosen as the test vehicle because it is has the “classic” sports car configuration with a long hood, short rear, and 2+2 passenger cabin while also being widely sold with a plethora of aftermarket aerodynamic modifications available. Due to computing and licensing restrictions, only a 2D CFD simulation was performed in ANSYS Fluent 19.1. A surface model of the centerline of the car was created in SolidWorks and imported into ANSYS, where the domain was created. A mesh convergence study was run to determine the optimum mesh size, and Realizable k-epsilon was the chosen physics model. The wind tunnel lacked equipment to record quantifiable data, so the wind tunnel was utilized for flow visualization on a 1/24 scale car model to compare with the CFD.
0° spoilers reduced the wake area behind the car, decreasing pressure drag but also decreasing underbody flow, causing a reduction in drag and downforce. Angled spoilers increased the wake area behind the car, increasing pressure drag but also increasing underbody flow, causing an increase in drag and downforce. Longer spoilers increased these effects compared to shorter spoilers, and short spoilers at different angles did not create significantly different effects. 0° spoilers would be best suited for cases that prioritize fuel economy or straight-line acceleration and speed due to the drag reduction, while angled spoilers would be best suited for cars requiring downforce. The angle and length of spoiler would depend on the downforce needed, which is dependent on the track.
0° spoilers reduced the wake area behind the car, decreasing pressure drag but also decreasing underbody flow, causing a reduction in drag and downforce. Angled spoilers increased the wake area behind the car, increasing pressure drag but also increasing underbody flow, causing an increase in drag and downforce. Longer spoilers increased these effects compared to shorter spoilers, and short spoilers at different angles did not create significantly different effects. 0° spoilers would be best suited for cases that prioritize fuel economy or straight-line acceleration and speed due to the drag reduction, while angled spoilers would be best suited for cars requiring downforce. The angle and length of spoiler would depend on the downforce needed, which is dependent on the track.
ContributorsNie, Alexander (Author) / Wells, Valana (Thesis director) / Huang, Huei-Ping (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2019-12
Description
The goal of this thesis project was to build an understanding of supersonic projectile dynamics through the creation of a trajectory model that incorporates several different aerodynamic concepts and builds a criteria for the stability of a projectile. This was done iteratively where the model was built from a foundation of kinematics with various aerodynamic principles being added incrementally. The primary aerodynamic principle that influenced the trajectory of the projectile was in the coefficient of drag. The drag coefficient was split into three primary components: the form drag, skin friction drag, and base pressure drag. These together made up the core of the model, additional complexity served to increase the accuracy of the model and generalize to different projectile profiles.
ContributorsBlair, Martin (Co-author) / Armenta, Francisco (Co-author) / Takahashi, Timothy (Thesis director) / Herrmann, Marcus (Committee member) / Mechanical and Aerospace Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2020-05
Description
This project aims to study the relationship between model input parameters and model output accuracy of the Tool for Automation of Computational Aerodynamics of Airfoils (TACAA). The input parameters of study are Mach number and Reynolds number, and inputs are tested through three flight speed regimes and from laminar to turbulent flow. Each of these input parameters are tested for the NACA 0012 and SC-1095 airfoils to ensure that the accuracy is similar regardless of geometric complexity. The TACAA program was used to run all simulation testing, and its overall functionality is discussed. The results gathered from the preliminary testing showed that the spread of variable input data points caused data gaps in the transonic regime results, which provided motivation to conduct further testing within the transonic region for both airfoils. After collecting all TACAA results, data from wind tunnel testing was compiled to compare. The comparison showed that (1) additional testing would be necessary to fully assess the accuracy of the results for the SC-1095 airfoil and (2) TACAA is generally accurate for compressible, turbulent flows.
ContributorsKuang, Joyce (Co-author) / Stickel, Hannah (Co-author) / Wells, Valana (Thesis director) / Duque, Earl (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2020-05
Description
This thesis will cover the basics of 2-dimensional motion of a parafoil system to determine and
design an altitude controller that will result in the parafoil starting at a location and landing within the
accepted bounds of a target location. It will go over the equations of motion, picking out the key
formulas that map out how a parafoil moves, and determine the key inputs in order to get the desired
outcome of a controlled trajectory. The physics found in the equations of motion will be turned into
state space representations that organize it into differential equations that coding software can make
use of to make trajectory calculations. MATLAB is the software used throughout the paper, and all code
used in the thesis paper will be written out for others to check and modify to their desires. Important
aspects of parafoil gliding motion will be discussed and tested with variables such as the natural glide
angle and velocity and the utilization of checkpoints in trajectory controller design. Lastly, the region of
attraction for the controller designed in this thesis paper will be discussed and plotted in order to show
the relationship between the four input variables, x position, y position, velocity, and theta.
The controller utilized in this thesis paper was able to plot a successful flight trajectory from
10m in the air to a target location 50m away. This plot is found in figure 18. The parafoil undershot the
target location by about 9 centimeters (0.18% error). This is an acceptable amount of error and shows
that the controller was a success in controlling the system to reach its target destination. When
compared to the uncontrolled flight in figure 17, the target will only be reached when a controller is
applied to the system.
design an altitude controller that will result in the parafoil starting at a location and landing within the
accepted bounds of a target location. It will go over the equations of motion, picking out the key
formulas that map out how a parafoil moves, and determine the key inputs in order to get the desired
outcome of a controlled trajectory. The physics found in the equations of motion will be turned into
state space representations that organize it into differential equations that coding software can make
use of to make trajectory calculations. MATLAB is the software used throughout the paper, and all code
used in the thesis paper will be written out for others to check and modify to their desires. Important
aspects of parafoil gliding motion will be discussed and tested with variables such as the natural glide
angle and velocity and the utilization of checkpoints in trajectory controller design. Lastly, the region of
attraction for the controller designed in this thesis paper will be discussed and plotted in order to show
the relationship between the four input variables, x position, y position, velocity, and theta.
The controller utilized in this thesis paper was able to plot a successful flight trajectory from
10m in the air to a target location 50m away. This plot is found in figure 18. The parafoil undershot the
target location by about 9 centimeters (0.18% error). This is an acceptable amount of error and shows
that the controller was a success in controlling the system to reach its target destination. When
compared to the uncontrolled flight in figure 17, the target will only be reached when a controller is
applied to the system.
ContributorsTeoharevic, Filip (Author) / Grewal, Anoop (Thesis director) / Lee, Hyunglae (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2020-05
Description
This experiment investigated the effects of different vortex generator sizes and configurations on the induced drag of a 2006 Honda Accord, with comparisons to a control test. Tuft tests were carried out prior to any data collection. The tufts were placed along the roof and rear window of the vehicle for each of the five vortex generator types. Video was taken of the tufts for each set of vortex generators, allowing a visual comparison of the flow characteristics with comparison to the control. Out of the four vortex generators tested, the two that yielded the most substantial change in the flow characteristics were utilized. The data collection was conducted utilizing the two sets of vortex generators, one large and one small, placed in three different locations along the roof of the vehicle. Over a course of four trials of data collection, each vortex generator size and configuration was tested two times along a stretch of Interstate 60, with each data set consisting of five minutes heading east, followed by five minutes heading west. Several experimental parameters were collected using an OBD II Bluetooth Adaptor, which were logged using the software compatible with the adaptor. This data was parsed and analyzed in Microsoft Excel and MATLAB. Utilizing an Analysis of Variance (ANOVA) analytical scheme, the data was generalized to account for terrain changes, steady state speed fluctuations, and weather changes per night. Overall, upon analysis of the data, the vortex generators showed little-to-no benefit to either the fuel efficiency or engine load experienced by the vehicle during the duration of the experiment. This result, while unexpected, is substantial as it shows that the expenditure of purchasing these vortex generators for this make and model of vehicle, and potentially other similar vehicles, is unnecessary as it produces no meaningful benefit.
ContributorsMazza, Seth (Author) / Walther, Chase (Co-author) / Takahashi, Timothy (Thesis director) / Middleton, James (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor)
Created2022-05
Description
This experiment investigated the effects of different vortex generator sizes and configurations on the induced drag of a 2006 Honda Accord, with comparisons to a control test. Tuft tests were carried out prior to any data collection. The tufts were placed along the roof and rear window of the vehicle for each of the five vortex generator types. Video was taken of the tufts for each set of vortex generators, allowing a visual comparison of the flow characteristics with comparison to the control. Out of the four vortex generators tested, the two that yielded the most substantial change in the flow characteristics were utilized. The data collection was conducted utilizing the two sets of vortex generators, one large and one small, placed in three different locations along the roof of the vehicle. Over a course of four trials of data collection, each vortex generator size and configuration was tested two times along a stretch of Interstate 60, with each data set consisting of five minutes heading east, followed by five minutes heading west. Several experimental parameters were collected using an OBD II Bluetooth Adaptor, which were logged using the software compatible with the adaptor. This data was parsed and analyzed in Microsoft Excel and MATLAB. Utilizing an Analysis of Variance (ANOVA) analytical scheme, the data was generalized to account for terrain changes, steady state speed fluctuations, and weather changes per night. Overall, upon analysis of the data, the vortex generators showed little-to-no benefit to either the fuel efficiency or engine load experienced by the vehicle during the duration of the experiment. This result, while unexpected, is substantial as it shows that the expenditure of purchasing these vortex generators for this make and model of vehicle, and potentially other similar vehicles, is unnecessary as it produces no meaningful benefit.
ContributorsWalther, Chase (Author) / Mazza, Seth (Co-author) / Takahashi, Timothy (Thesis director) / Middleton, James (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor)
Created2022-05