Matching Items (12)
Filtering by

Clear all filters

134285-Thumbnail Image.png
Description
This experiment used hotwire anemometry to examine the von Kármán vortex street and how different surface conditions affect the wake profile of circular airfoils, or bluff bodies. Specifically, this experiment investigated how the various surface conditions affected the shedding frequency and Strouhal Number of the vortex street as Reynolds Number

This experiment used hotwire anemometry to examine the von Kármán vortex street and how different surface conditions affect the wake profile of circular airfoils, or bluff bodies. Specifically, this experiment investigated how the various surface conditions affected the shedding frequency and Strouhal Number of the vortex street as Reynolds Number is increased. The cylinders tested varied diameter, surface finish, and wire wrapping. Larger diameters corresponded with lower shedding frequencies, rougher surfaces decreased Strouhal Number, and the addition of thick wires to the surface of the cylinder completely disrupted the vortex shedding to the point where there was almost no dominant shedding frequency. For the smallest diameter cylinder tested, secondary dominant frequencies were observed, suggesting harmonics.
ContributorsCoote, Peter John (Author) / Takahashi, Timothy (Thesis director) / White, Daniel (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2017-05
137262-Thumbnail Image.png
Description
The thesis is an investigation on current regulations of commercial aircraft landing and take-off procedures and an analysis of potential weaknesses within the regulatory system for commercial aerospace. To determine such flaws, an area of worse-case scenarios with regard to the aforementioned flight operations was researched. The events selected to

The thesis is an investigation on current regulations of commercial aircraft landing and take-off procedures and an analysis of potential weaknesses within the regulatory system for commercial aerospace. To determine such flaws, an area of worse-case scenarios with regard to the aforementioned flight operations was researched. The events selected to best-depict these scenarios where incidents of aircraft overrunning the runway, referred to as runway excursions. A case-study conducted of 44 federal investigations of runway excursions produced data indicating four influential factors within these incidents: weather, pilot error, instrument malfunction, and runway condition. Upon examination, all but pilot error appeared to have federal enforcement to diminish the occurrence of future incidents. This is a direct result of the broad possibilities that make up this factor. The study then searched for a consistent fault within the incidents with the results indicating an indirect relationship of thrust reversers, a technique utilized by pilots to provide additional braking, to these excursions. In cases of thrust reverser failure, pilots' over-reliance on the system lead to time being lost from the confusion produced by the malfunction, ultimately resulting in several different runway excursions. The legal implication with the situation is that current regulations are ambiguous on the subject of thrust reversers and thus do not properly model the usage of the technique. Thus, to observe the scope of danger this ambiguity presents to the industry, the relationship of the technique to commercial aerospace needed to be determined. Interviews were set-up with former commercial pilots to gather data related to the flight crew perspective. This data indicated that thrust reversers were actively utilized by pilots within the industry for landing operations. The problem with the current regulations was revealed that the lack of details on thrust reverser reflected a failure of regulations to model current industry flight operations. To improve safety within the industry, new data related to thrust reverser deployment must be developed and enforced to determine appropriate windows to utilize the technique, thus decreasing time lost in confusion that results from thrust reversers malfunction. Future work would be based on producing simulations to determine said data as well as proposing the policy suggestions produced by this thesis.
ContributorsCreighton, Andrew John (Author) / Takahashi, Timothy (Thesis director) / Marchant, Gary (Committee member) / Kimberly, Jimmy (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor) / School of Mathematical and Statistical Sciences (Contributor) / School of Politics and Global Studies (Contributor)
Created2014-05
134673-Thumbnail Image.png
Description
This paper describes an aircraft design optimization tool for wave drag reduction. The tool synthesizes an aircraft wing and fuselage geometry using the Rhinoceros CAD program. It then implements an algorithm to perform area-ruling on the fuselage. The algorithm adjusts the cross-sectional area along the length of the fuselage, with

This paper describes an aircraft design optimization tool for wave drag reduction. The tool synthesizes an aircraft wing and fuselage geometry using the Rhinoceros CAD program. It then implements an algorithm to perform area-ruling on the fuselage. The algorithm adjusts the cross-sectional area along the length of the fuselage, with the wing geometry fixed, to match a Sears-Haack distribution. Following the optimization of the area, the tool collects geometric data for analysis using legacy performance tools. This analysis revealed that performing the optimization yielded an average reduction in wave drag of 25% across a variety of Mach numbers on two different starting geometries. The goal of this project is to integrate this optimization tool into a larger trade study tool as it will allow for higher fidelity modeling as well as large improvements in transonic and supersonic drag performance.
ContributorsLeader, Robert William (Author) / Takahashi, Timothy (Thesis director) / Middleton, James (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-12
133322-Thumbnail Image.png
Description
Each year, the CanSat Competition organizers release aerospace based engineering mission objectives for collegiate teams to compete in. This year, the design is an aerodynamically stable probe that will descend from an altitude of 725 meters at a rate between 10-30 meters/sec until it reaches an altitude of 300 meters,

Each year, the CanSat Competition organizers release aerospace based engineering mission objectives for collegiate teams to compete in. This year, the design is an aerodynamically stable probe that will descend from an altitude of 725 meters at a rate between 10-30 meters/sec until it reaches an altitude of 300 meters, where it will then release a parachute as its aerobraking mechanism as it descends at 5 meters/sec until it reaches the ground. The focus of this paper is to investigate the design of the probe itself and how slender body theory and cross flow drag affect the lift and aerodynamic stability of this bluff body. A tool is developed inside of MATLAB which calculates the slender body lift as well as the lift from the cross flow drag. It then uses that information to calculate the total moment about the center of gravity for a range of angles of attack and free stream velocities. This tool is then used to optimize the geometry of the probe. These geometries are used to construct a prototype and that prototype is tested by a drop test from a 6-story building. The initial tests confirm the calculations that the probe, bluff body, is stable and self-correcting in its descent. Future work involves more high-altitude and ground-level tests that will further verify and improve on the current design.
ContributorsMcCourt, Anthony Michael (Author) / Takahashi, Timothy (Thesis director) / Herrmann, Marcus (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
133327-Thumbnail Image.png
Description
This paper outlines the development of a script which utilizes a series of user-defined input parameters to construct base-level CAD models of aircraft landing gear. With an increased focus on computation development of aircraft models to allow for a rapidprototyping design process, this program seeks to allow designers to check

This paper outlines the development of a script which utilizes a series of user-defined input parameters to construct base-level CAD models of aircraft landing gear. With an increased focus on computation development of aircraft models to allow for a rapidprototyping design process, this program seeks to allow designers to check for the validity of design integration before moving forward on systems testing. With this script, users are able to visually analyze the landing gear configurations on an aircraft in both the gear up and gear down configuration. The primary purpose this serves is to determine the validity of the gear's potential to fit within the limited real estate on an aircraft body. This, theoretically, can save time by weeding out infeasible designs before moving forward with subsystem performance testing. The script, developed in Python, constructs CAD models of dual and dual-tandem main landing gear configurations in the CAD program Rhino5. With an included design template consisting of 33 parameters, the script allows for a reasonable trade off between conciseness and flexibility of design.
ContributorsPatrick, Noah Edward (Author) / Takahashi, Timothy (Thesis director) / Middleton, James (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
135623-Thumbnail Image.png
Description
The aerodynamics of golf club heads effect the forces on the club head throughout the swing. The bluff body geometry and passive flow control elements make the aerodynamics of golf club heads far more complex. The theory behind the geometry of the bluff body aerodynamics relies on the

The aerodynamics of golf club heads effect the forces on the club head throughout the swing. The bluff body geometry and passive flow control elements make the aerodynamics of golf club heads far more complex. The theory behind the geometry of the bluff body aerodynamics relies on the state of the boundary layer and its interaction with the golf club head. Laminar and turbulent boundary layer flow result in drag, but in varying degrees. Separation, or attachment, of the boundary layer in these laminar and turbulent boundary layer flows is part of the cause of the induced drag. Skin friction and pressure drag are the two forms of surface forces which vary according to the state of the boundary layer. To review the state of the boundary layer flow and provide validation data for the corresponding, the golf club head was tested in a wind tunnel. Drag readings from the experiment showed the lowest drag occurred while the club face was perpendicular to the flow from the range of 50 miles per hour to 90 miles per hour. Additionally, the decrease in drag varied greatly depending on the orientation of golf club head. The decrease in the coefficient for the club perpendicular to the flow was approximately 3.99*〖10〗^(-6) C_d/Re while the decrease for the club at 110° was 1.07*〖10〗^(-6) C_d/Re. The general trend of the slopes indicated the pressure drag resulted in major variations while the drag due to skin friction remained relatively constant.
For the testing of the golf club head, two probes were developed to measure the turbulent intensity in the flow. The probes, based on Rossow’s (1993) three probe system, compared the dynamic pressure of the flow with the stream-wise dynamic pressure in the flow. The resultant measurements could then produce the ratio of the cross-stream fluctuations in velocity to the time-averaged velocity. The turbulence intensity calculations would provide insight on the turbulence in the boundary layer flow and wake.
ContributorsBrausch, Matthew James (Author) / Takahashi, Timothy (Thesis director) / Ghods, Sina (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-05
Description

The following analysis was conducted at the Arizona State University open loop wind tunnel. Two 1/24-th scale NASCAR models were placed in a wind tunnel test section and were adjusted to study drafting that commonly occurs at superspeedway racetracks. The purpose of the experiment was to determine how drafting affects

The following analysis was conducted at the Arizona State University open loop wind tunnel. Two 1/24-th scale NASCAR models were placed in a wind tunnel test section and were adjusted to study drafting that commonly occurs at superspeedway racetracks. The purpose of the experiment was to determine how drafting affects a leading and trailing car through changes in distance. A wind tunnel model was developed consisting of two 2019 NASCAR Chevy Camaro race car models, two bar-style load cells, and a programmed Arduino UNO. Two trials were run at each drafting distance, 0, 0.5, 1, 1.5, and 2 car lengths apart. Each trial was run at a wind tunnel velocity of 78 mph (35 m/s) and force data was collected to represent the drag effects at each drafting location. Based on previously published experimentation, this analysis provided important data that related drafting effects in scale model race cars to full-scale vehicles. The experiment showed that scale model testing can be accurately completed when the wind tunnel Reynolds number is of the same magnitude as a full-scale NASCAR. However, the wind tunnel data collected was proven to be fully laminar flow and did not compare to the flow characteristics of typically turbulent flow seen in superspeedway races. Overall, the analytical drag analysis of drafting NASCAR models proved that wind tunnel testing is only accurate when many parameters are met and should only be used as a method of validation to full-scale testing.

ContributorsOlszak, Parker T (Author) / Takahashi, Timothy (Thesis director) / Kasbaoui, Mohamed (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2021-05
131986-Thumbnail Image.png
Description
An experimental investigation was conducted to calculate the aerodynamic drag on a cyclist wearing different types of clothing. The different outfits worn for this experiment were a professional skinsuit, a professional cycling kit, a t-shirt and shorts, and a long-sleeved flannel and jeans. The aerodynamic drag was ultimately found using

An experimental investigation was conducted to calculate the aerodynamic drag on a cyclist wearing different types of clothing. The different outfits worn for this experiment were a professional skinsuit, a professional cycling kit, a t-shirt and shorts, and a long-sleeved flannel and jeans. The aerodynamic drag was ultimately found using the coast down method, a process in which a cyclist increases their speed to a chosen maximum threshold, and upon reaching this speed, ceases the pedal stroke and maintains the aero position until the bicycle comes to a stop. The data was gathered using an AeroPod, speed sensor, and GPS unit. The data gathered was imported into Excel for data analysis. The average CdA values at race speed (26-30 ft/s) for the skinsuit, cycling kit, t-shirt and shorts, and flannel were calculated to be 4.180 ft2, 3.668 ft2, 4.884 ft2, and 4.223 ft2, respectively. These race speed averages were found using data from three separate Ironman Triathlons. The cycling kit was found to be the most aerodynamic at the race speed. The results of this study reveal that cycling apparel can only be optimized for a small range of speeds and cycling outside of this optimal range delays the initiation of the reduction of boundary layer separation, thus resulting in more critical time spent in the flow transition region. The skinsuit’s performance was more aerodynamically efficient than the cycling kit at speeds greater than 36.8 mph. The cycling kit is more aerodynamic for speeds slower than 36.8 mph. The slickness of the skinsuit was found to be detrimental to the cyclist’s aerodynamic drag, as the lack of roughness on the skinsuit prevented the initiation of turbulent flow, which results in a decrease in drag. Overall, the experiment confirmed the hypothesis that a cyclist is more aerodynamic when wearing cycling apparel as opposed to casual, loose-fitting clothing.
ContributorsGlynn, Julia Daniel (Co-author) / Duffy, Kyle (Co-author) / Takahashi, Timothy (Thesis director) / Bergmann, Ande (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Department of Information Systems (Contributor) / Barrett, The Honors College (Contributor)
Created2019-12
131763-Thumbnail Image.png
Description
The goal of this thesis project was to build an understanding of supersonic projectile dynamics through the creation of a trajectory model that incorporates several different aerodynamic concepts and builds a criteria for the stability of a projectile. This was done iteratively where the model was built from a foundation

The goal of this thesis project was to build an understanding of supersonic projectile dynamics through the creation of a trajectory model that incorporates several different aerodynamic concepts and builds a criteria for the stability of a projectile. This was done iteratively where the model was built from a foundation of kinematics with various aerodynamic principles being added incrementally. The primary aerodynamic principle that influenced the trajectory of the projectile was in the coefficient of drag. The drag coefficient was split into three primary components: the form drag, skin friction drag, and base pressure drag. These together made up the core of the model, additional complexity served to increase the accuracy of the model and generalize to different projectile profiles.
ContributorsBlair, Martin (Co-author) / Armenta, Francisco (Co-author) / Takahashi, Timothy (Thesis director) / Herrmann, Marcus (Committee member) / Mechanical and Aerospace Engineering Program (Contributor, Contributor) / Barrett, The Honors College (Contributor)
Created2020-05
166193-Thumbnail Image.png
Description
This experiment investigated the effects of different vortex generator sizes and configurations on the induced drag of a 2006 Honda Accord, with comparisons to a control test. Tuft tests were carried out prior to any data collection. The tufts were placed along the roof and rear window of the vehicle

This experiment investigated the effects of different vortex generator sizes and configurations on the induced drag of a 2006 Honda Accord, with comparisons to a control test. Tuft tests were carried out prior to any data collection. The tufts were placed along the roof and rear window of the vehicle for each of the five vortex generator types. Video was taken of the tufts for each set of vortex generators, allowing a visual comparison of the flow characteristics with comparison to the control. Out of the four vortex generators tested, the two that yielded the most substantial change in the flow characteristics were utilized. The data collection was conducted utilizing the two sets of vortex generators, one large and one small, placed in three different locations along the roof of the vehicle. Over a course of four trials of data collection, each vortex generator size and configuration was tested two times along a stretch of Interstate 60, with each data set consisting of five minutes heading east, followed by five minutes heading west. Several experimental parameters were collected using an OBD II Bluetooth Adaptor, which were logged using the software compatible with the adaptor. This data was parsed and analyzed in Microsoft Excel and MATLAB. Utilizing an Analysis of Variance (ANOVA) analytical scheme, the data was generalized to account for terrain changes, steady state speed fluctuations, and weather changes per night. Overall, upon analysis of the data, the vortex generators showed little-to-no benefit to either the fuel efficiency or engine load experienced by the vehicle during the duration of the experiment. This result, while unexpected, is substantial as it shows that the expenditure of purchasing these vortex generators for this make and model of vehicle, and potentially other similar vehicles, is unnecessary as it produces no meaningful benefit.
ContributorsMazza, Seth (Author) / Walther, Chase (Co-author) / Takahashi, Timothy (Thesis director) / Middleton, James (Committee member) / Barrett, The Honors College (Contributor) / Mechanical and Aerospace Engineering Program (Contributor)
Created2022-05