Matching Items (53)
Filtering by
- All Subjects: Mechanical Engineering
- Creators: Huang, Huei-Ping
- Member of: Theses and Dissertations
Description
This study uses Computational Fluid Dynamics (CFD) modeling to analyze the
dependence of wind power potential and turbulence intensity on aerodynamic design of a
special type of building with a nuzzle-like gap at its rooftop. Numerical simulations using
ANSYS Fluent are carried out to quantify the above-mentioned dependency due to three
major geometric parameters of the building: (i) the height of the building, (ii) the depth of
the roof-top gap, and (iii) the width of the roof-top gap. The height of the building is varied
from 8 m to 24 m. Likewise, the gap depth is varied from 3 m to 5 m and the gap width
from 2 m to 4 m. The aim of this entire research is to relate these geometric parameters of
the building to the maximum value and the spatial pattern of wind power potential across
the roof-top gap. These outcomes help guide the design of the roof-top geometry for wind
power applications and determine the ideal position for mounting a micro wind turbine.
From these outcomes, it is suggested that the wind power potential is greatly affected by
the increasing gap width or gap depth. It, however, remains insensitive to the increasing
building height, unlike turbulence intensity which increases with increasing building
height. After performing a set of simulations with varying building geometry to quantify
the wind power potential before the installation of a turbine, another set of simulations is
conducted by installing a static turbine within the roof-top gap. The results from the latter
are used to further adjust the estimate of wind power potential. Recommendations are made
for future applications based on the findings from the numerical simulations.
dependence of wind power potential and turbulence intensity on aerodynamic design of a
special type of building with a nuzzle-like gap at its rooftop. Numerical simulations using
ANSYS Fluent are carried out to quantify the above-mentioned dependency due to three
major geometric parameters of the building: (i) the height of the building, (ii) the depth of
the roof-top gap, and (iii) the width of the roof-top gap. The height of the building is varied
from 8 m to 24 m. Likewise, the gap depth is varied from 3 m to 5 m and the gap width
from 2 m to 4 m. The aim of this entire research is to relate these geometric parameters of
the building to the maximum value and the spatial pattern of wind power potential across
the roof-top gap. These outcomes help guide the design of the roof-top geometry for wind
power applications and determine the ideal position for mounting a micro wind turbine.
From these outcomes, it is suggested that the wind power potential is greatly affected by
the increasing gap width or gap depth. It, however, remains insensitive to the increasing
building height, unlike turbulence intensity which increases with increasing building
height. After performing a set of simulations with varying building geometry to quantify
the wind power potential before the installation of a turbine, another set of simulations is
conducted by installing a static turbine within the roof-top gap. The results from the latter
are used to further adjust the estimate of wind power potential. Recommendations are made
for future applications based on the findings from the numerical simulations.
ContributorsKailkhura, Gargi (Author) / Huang, Huei-Ping (Thesis advisor) / Rajagopalan, Jagannathan (Committee member) / Forzani, Erica (Committee member) / Arizona State University (Publisher)
Created2017
Description
The formation and stability of a slowly evolving zonal jet in 2-D flow with beta effect is analyzed using the model developed by Manfroi and Young in which the final governing equation was derived by means of a perturbation analysis of a barotropic vorticity equation with sinusoidal meridional mean flow. However in the original study the term β0, that represents the effect of large-scale Rossby waves, was dropped and was proceeded on a path of finding solutions for a simplified 1-D flow. The idea of this study is to understand the effects of the dropped term on the overall dynamics of the zonal jet evolution. For this purpose the system that is entirely deterministic with no additional forcing is solved by means of a standard finite difference scheme. The Numerical solutions are found for varying β0 and μ values where μ represents the bottom drag. In addition to this the criteria for the formation of zonal jets developed originally for the 1-D system is verified for the 2-D system as well. The study reveals the similarity in some of the results of the 1-D and the 2-D system like the merging of jets in the absence of bottom drag, formation of steady jets in presence of a non-zero bottom drag and the adherence to the boundary criteria for the formation of zonal jets. But when it comes to the formation of steady jets, a finite β0 value is required above which the solution is similar to the 1-D system. Also the jets formed under the presence of non-zero bottom drag seem wavy in nature which is different from the steady horizontal jets produced in the 1-D system.
ContributorsRaghunathan, Girish Nigamanth (Author) / Huang, Huei-Ping (Thesis advisor) / Herrmann, Marcus (Committee member) / Chen, Kangping (Committee member) / Arizona State University (Publisher)
Created2017
Description
The aerospike nozzle belongs to the class of altitude compensating nozzles making it a strong candidate for Space Shuttle Main Engines. Owing to their higher efficiency compared to conventional bell nozzles, the aerospike nozzles are being studied extensively and are being used for many Single State to Orbit (SSTO) designs. A rocket engine nozzle with altitude compensation, such as the aerospike, consumes less fuel than a rocket engine with a bell nozzle. Aerospike nozzles are huge and are often difficult to construct and have to be truncated in order to make them feasible for application in a rocket propulsion system. Consequently, truncation of the aerospike leads to pressure loss under the base, which in-turn decreases the overall thrust produced by the rocket nozzle. To overcome this loss, a technique called base bleed is implemented in which a secondary jet is made to flow through the base of the truncated portion. This thesis uses dynamic pressure contour plots to find out the ideal base bleed mass flow rate to avoid base recirculation in 10 %, 20 % and 30 % truncated aerospike nozzles.
ContributorsNagarajan, Venkatraman (Author) / White, Daniel B (Thesis advisor) / Dahm, Werner (Thesis advisor) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2017
Description
The effect of reduced frequency on dynamic stall behavior of a pitching NACA0012 airfoil in a turbulent wake using Direct Numerical Simulations is presented in the current study. Upstream turbulence with dynamically oscillating blades and airfoils is associated with ambient flow unsteadiness and is encountered in many operating conditions. Wake turbulence, a more realistic scenario for airfoils in operation, is generated using a small solid cylinder placed upstream, the vortices shed from which interact with the pitching airfoil affecting dynamic stall behavior.
A recently developed moving overlapping grid approach is used using a high-order Spectral Element Method (SEM) for spatial discretization combined with a dynamic time-stepping procedure allowing for up to third order temporal discretization. Two cases of reduced frequency (k = 0:16 and 0:25) for airfoil oscillation are investigated and the change in dynamic stall behavior with change in reduced frequency is studied and documented using flow-fields and aerodynamic coefficients (Drag, Lift and Pitching Moment) with a focus on understanding vortex system dynamics (including formation of secondary vortices) for different reduced frequencies and it’s affect on airfoil aerodynamic characteristics and fatigue life. Transition of the flow over the surface of an airfoil for both undisturbed and disturbed flow cases will also be discussed using Pressure coefficient and Skin Friction coefficient data for a given cycle combined with a wavelet analysis using Morse wavelets in MATLAB.
A recently developed moving overlapping grid approach is used using a high-order Spectral Element Method (SEM) for spatial discretization combined with a dynamic time-stepping procedure allowing for up to third order temporal discretization. Two cases of reduced frequency (k = 0:16 and 0:25) for airfoil oscillation are investigated and the change in dynamic stall behavior with change in reduced frequency is studied and documented using flow-fields and aerodynamic coefficients (Drag, Lift and Pitching Moment) with a focus on understanding vortex system dynamics (including formation of secondary vortices) for different reduced frequencies and it’s affect on airfoil aerodynamic characteristics and fatigue life. Transition of the flow over the surface of an airfoil for both undisturbed and disturbed flow cases will also be discussed using Pressure coefficient and Skin Friction coefficient data for a given cycle combined with a wavelet analysis using Morse wavelets in MATLAB.
ContributorsGandhi, Anurag (Author) / Peet, Yulia (Thesis advisor) / Huang, Huei-Ping (Committee member) / Herrmann, Marcus (Committee member) / Arizona State University (Publisher)
Created2017
Description
Space systems such as communication satellites, earth observation satellites and telescope require accurate pointing to observe fixed targets over prolonged time. These systems typically use reaction wheels to slew the spacecraft and gimballing systems containing motors to achieve precise pointing. Motor based actuators have limited life as they contain moving parts that require lubrication in space. Alternate methods have utilized piezoelectric actuators. This paper presents Shape memory alloys (SMA) actuators for control of a deployable antenna placed on a satellite. The SMAs are operated as a series of distributed linear actuators. These distributed linear actuators are not prone to single point failures and although each individual actuator is imprecise due to hysteresis and temperature variation, the system as a whole achieves reliable results. The SMAs can be programmed to perform a series of periodic motion and operate as a mechanical guidance system that is not prone to damage from radiation or space weather. Efforts are focused on developing a system that can achieve 1 degree pointing accuracy at first, with an ultimate goal of achieving a few arc seconds accuracy. Bench top model of the actuator system has been developed and working towards testing the system under vacuum. A demonstration flight of the technology is planned aboard a CubeSat.
ContributorsSonawane, Nikhil (Author) / Thangavelautham, Jekanthan (Thesis advisor) / Huang, Huei-Ping (Thesis advisor) / Solanki, Kiran (Committee member) / Arizona State University (Publisher)
Created2016
Description
Passive flow control achieved by surface dimpling can be an effective strategy for reducing drag around bluff bodies - an example of substantial popular interest being the flow around a golf ball. While the general effect of dimples causing a delay of boundary layer separation is well known, the mechanisms contributing to this phenomena are subtle and not thoroughly understood. Numerical models offer a powerful approach for studying drag reduction, however simulation strategies are challenged by complex geometries, and in applications the introduction of ad hoc turbulence models which introduce additional uncertainty. These and other factors provide much of the motivation for the current study, which focused on the numerical simulations of the flow over a simplified configuration consisting of a dimpled flat plate. The principal goals of the work are to understand the performance of the numerical methodology, and gain insight into the underlying physics of the flow. Direct numerical simulation of the incompressible Navier-Stokes equations using a fractional step method was employed, with the dimpled flat plate represented using an immersed boundary method. The dimple geometry utilizes a fixed dimple aspect ratio, with dimples arranged in a single spanwise row. The grid sizes considered ranged from approximately 3 to 99 million grid points. Reynolds numbers of 3000 and 4000 based on the inlet laminar boundary layer thickness were simulated. A turbulent boundary layer was induced downstream of the dimples for Reynolds numbers which did not transition for the flow over an undimpled flat plate. First and second order statistics of the boundary layer that develops agree reasonably well with those for turbulent channel flow and flat plate boundary layers in the sublayer and buffer layers, but differ in the outer layer. Inspection of flow visualizations suggest that early transition is promoted by thinning of the boundary layer, initiation of shear layer instabilities over the dimples, flow separation and reattachment, and tripping of the boundary layer at the trailing edge of the dimples.
ContributorsMode, Jeffrey Michael (Author) / Squires, Kyle (Thesis advisor) / Herrmann, Marcus (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2010
Description
Stiffness and flexibility are essential in many fields, including robotics, aerospace, bioengineering, etc. In recent years, origami-based mechanical metamaterials were designed for better mechanical properties including tunable stiffness and tunable collapsibility. However, in existing studies, the tunable stiffness is only with limited range and limited controllability. To overcome these challenges, two objectives were proposed and achieved in this dissertation: first, to design mechanical metamaterials with metamaterials with selective stiffness and collapsibility; second, to design mechanical metamaterials with in-situ tunable stiffness among positive, zero, and negative.In the first part, triangulated cylinder origami was employed to build deployable mechanical metamaterials through folding and unfolding along the crease lines. These deployable structures are flexible in the deploy direction so that it can be easily collapsed along the same way as it was deployed. An origami-inspired mechanical metamaterial was designed for on-demand deployability and selective collapsibility: autonomous deployability from the collapsed state and selective collapsibility along two different paths, with low stiffness for one path and substantially high stiffness for another path. The created mechanical metamaterial yields unprecedented load bearing capability in the deploy direction while possessing great deployability and collapsibility. The principle in this prospectus can be utilized to design and create versatile origami-inspired mechanical metamaterials that can find many applications.
In the second part, curved origami patterns were designed to accomplish in situ stiffness manipulation covering positive, zero, and negative stiffness by activating predefined creases on one curved origami pattern. This elegant design enables in situ stiffness switching in lightweight and space-saving applications, as demonstrated through three robotic-related components. Under a uniform load, the curved origami can provide universal gripping, controlled force transmissibility, and multistage stiffness response. This work illustrates an unexplored and unprecedented capability of curved origami, which opens new applications in robotics for this particular family of origami patterns.
ContributorsZhai, Zirui (Author) / Nian, Qiong (Thesis advisor) / Zhuang, Houlong (Committee member) / Huang, Huei-Ping (Committee member) / Zhang, Wenlong (Committee member) / Liu, Yongming (Committee member) / Arizona State University (Publisher)
Created2021
Description
Intelligent engineering designs require an accurate understanding of material behavior, since any uncertainties or gaps in knowledge must be counterbalanced with heightened factors of safety, leading to overdesign. Therefore, building better structures and pushing the performance of new components requires an improved understanding of the thermomechanical response of advanced materials under service conditions. This dissertation provides fundamental investigations of several advanced materials: thermoset polymers, a common matrix material for fiber-reinforced composites and nanocomposites; aluminum alloy 7075-T6 (AA7075-T6), a high-performance aerospace material; and ceramic matrix composites (CMCs), an advanced composite for extreme-temperature applications. To understand matrix interactions with various interfaces and nanoinclusions at their fundamental scale, the properties of thermoset polymers are studied at the atomistic scale. An improved proximity-based molecular dynamics (MD) technique for modeling the crosslinking of thermoset polymers is carefully established, enabling realistic curing simulations through its ability to dynamically and probabilistically perform complex topology transformations. The proximity-based MD curing methodology is then used to explore damage initiation and the local anisotropic evolution of mechanical properties in thermoset polymers under uniaxial tension with an emphasis on changes in stiffness through a series of tensile loading, unloading, and reloading experiments. Aluminum alloys in aerospace applications often require a fatigue life of over 109 cycles, which is well over the number of cycles that can be practically tested using conventional fatigue testing equipment. In order to study these high-life regimes, a detailed ultrasonic cycle fatigue study is presented for AA7075-T6 under fully reversed tension-compression loading. The geometric sensitivity, frequency effects, size effects, surface roughness effects, and the corresponding failure mechanisms for ultrasonic fatigue across different fatigue regimes are investigated. Finally, because CMCs are utilized in extreme environments, oxidation plays an important role in their degradation. A multiphysics modeling methodology is thus developed to address the complex coupling between oxidation, mechanical stress, and oxygen diffusion in heterogeneous carbon fiber-reinforced CMC microstructures.
ContributorsSchichtel, Jacob (Author) / Chattopadhyay, Aditi (Thesis advisor) / Dai, Lenore (Committee member) / Ghoshal, Anindya (Committee member) / Huang, Huei-Ping (Committee member) / Jiao, Yang (Committee member) / Oswald, Jay (Committee member) / Arizona State University (Publisher)
Created2022
Description
Computing the fluid phase interfaces in multiphase flow is a challenging area of research in fluids. The Volume of Fluid andLevel Set methods are a few algorithms that have been developed for reconstructing the multiphase fluid flow interfaces.
The thesis work focuses on exploring the ability of neural networks to reconstruct the multiphase fluid flow interfaces using
a data-driven approach.
The neural network model has liquid volume fraction stencils as an input, and it predicts the radius of the circle as an
output of the network which represents a phase interface separating two immiscible fluids inside a fluid domain. The liquid
volume fraction stencils are generated for randomly varying circle radii within a 1x1 domain using an open-source VOFI
library. These datasets are used to train the neural network. Once the model is trained, the predicted circular phase
interface from the neural network output is used to generate back the predicted liquid volume fraction stencils.
Error norms values are calculated to assess the error in the neural network model’s predicted liquid volume fraction
stencils with the actual liquid volume fraction stencils from the VOFI library. The neural network parameters are optimized
by testing them for different hyper-parameters to reduce the error norms. So as to minimize the difference between the
predicted and the actual liquid volume fraction stencils and errors in reconstructing the fluid phase interface geometry.
ContributorsPawar, Pranav Rajesh (Author) / Herrmann, Marcus (Thesis advisor) / Zhuang, Houlong (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2023
Description
The conversion of H2S enables the recycling of a waste gas into a potential source of hydrogen at a lower thermodynamic energy cost as compared to water splitting. However, studies on the photocatalytic decomposition of H2S focus on traditional deployment of catalyst materials to facilitate this conversion, and operation only when a light source is available. In this study, the efficacy of Direct Ink Written (DIW) luminous structures for H2S conversion has been investigated, with the primary objective of sustaining H2S conversion when a light source has been terminated. Additionally, as a secondary objective, improving light distribution within monoliths for photocatalytic applications is desired. The intrinsic illumination of the 3D printed monoliths developed in this work could serve as an alternative to monolith systems that employ light transmitting fiber optic cables that have been previously proposed to improve light distribution in photocatalytic systems. The results that were obtained demonstrate that H2S favorable adsorbents, a wavelength compatible long afterglow phosphor, and a photocatalyst can form viscoelastic inks that are printable into DIW luminous monolithic contactors. Additionally, rheological, optical and porosity analyses conducted, provide design guidelines for future studies seeking to develop DIW luminous monoliths from compatible catalyst-phosphor pairs. The monoliths that were developed demonstrate not only improved conversion when exposed to light, but more significantly, extended H2S conversion from the afterglow of the monoliths when an external light source was removed. Lastly, considering growing interests in attaining a global circular economy, the techno-economic feasibility of a H2S-CO2 co-utilization plant leveraging hydrogen from H2S photocatalysis as a feed source for a downstream CO2 methanation plant has been assessed. The work provides preliminary information to guide future chemical kinetic design characteristics that are important to strive for if using H2S as a source of hydrogen in a CO2 methanation facility.
ContributorsAbdullahi, Adnan (Author) / Andino, Jean (Thesis advisor) / Phelan, Patrick (Thesis advisor) / Bhate, Dhruv (Committee member) / Wang, Robert (Committee member) / Huang, Huei-Ping (Committee member) / Arizona State University (Publisher)
Created2023