Matching Items (8)
Filtering by

Clear all filters

133605-Thumbnail Image.png
Description
Carbon capture is an essential way to reduce greenhouse gas emissions. One way to decrease the emissions is through the use of adsorbents such as zeolites. Dr. Dong-Kyun Seo’s group (School of Molecular Sciences, Arizona State University) synthesized the nanostructured faujasite (NaX). The zeolite was characterized using Scanning Electron Microscopy

Carbon capture is an essential way to reduce greenhouse gas emissions. One way to decrease the emissions is through the use of adsorbents such as zeolites. Dr. Dong-Kyun Seo’s group (School of Molecular Sciences, Arizona State University) synthesized the nanostructured faujasite (NaX). The zeolite was characterized using Scanning Electron Microscopy (SEM) and the physisorption properties were determined using ASAP 2020. ASAP 2020 tests of the nano-zeolite pellets at 77K in a liquid N2 bath determined the BET surface area of 547.1 m2/mol, T-plot micropore volume of 0.2257 cm3/g, and an adsorption average pore width of 5.9 Å. The adsorption isotherm (equilibrium) of CH4, N2, and CO2 were measured at 25ºC. Adsorption isotherm experiments concluded that the linear isotherm was the best fit for N2, and CH4 and the Sips isotherm was a better fit than the Langmuir and Freundlich isotherm for CO2. At 25ºC and 1 atm the zeolite capacity for CO2 is 4.3339 mmol/g, 0.1948 mmol/g for CH4, and 0.3534 mmol/g for N2. The zeolite has a higher CO2 capacity than the conventional NaX zeolite. Breakthrough experiments were performed in a fixed bed 22in, 0.5 in packing height and width at 1 atm and 298 K with nano-zeolite pellets. The gas chromatographer tested and recorded the data every two minutes with a flow rate of 10 cm3/min for N2 and 10 cm3/min CO2. Breakthrough simulations of the zeolite in a fixed bed adsorber column were conducted on MATLAB utilizing varying pressures, flow rates, and fed ratios of various CO2, N2 and CH4. Simulations using ideal adsorbed solution theory (IAST) calculations determined that the selectivity of CO2 in flue gas (15% CO2 + 85% N2) is 571.79 at 1 MPa, significantly higher than commercial zeolites and literature. The nanostructured faujasite zeolite appears to be a very promising adsorbent for CO2/N2 capture from flue gas and the separation of CO2/N2.
ContributorsClark, Krysta D. (Author) / Deng, Shuguang (Thesis director) / Green, Matthew (Committee member) / Chemical Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2018-05
137240-Thumbnail Image.png
Description
The goals of the styrene oxide adsorption experiments were to develop reliable isotherms of styrene oxide onto Dowex Optipore L-493 resin and onto mesoporous carbon adsorbents, in addition to determining the ideal conditions for styrene oxide production from E. coli. Adsorption is an effective means of separation used in industry

The goals of the styrene oxide adsorption experiments were to develop reliable isotherms of styrene oxide onto Dowex Optipore L-493 resin and onto mesoporous carbon adsorbents, in addition to determining the ideal conditions for styrene oxide production from E. coli. Adsorption is an effective means of separation used in industry to separate compounds, often organics from air and water. Styrene oxide adsorption runs without E. coli were conducted at concentrations ranging from 0.15 to 3.00 g/L with resin masses ranging from 0.1 to 0.5 g of Dowex Optipore L-493 and 0.5 to 0.75 g of mesoporous carbon adsorbent. Runs were conducted on a shake plate operating at 80 rpm for 24 hours at ambient temperature. Isotherms were developed from the results and then adsorption experiments with E. coli and L-493 were performed. Runs were conducted at glucose concentrations ranging from 20-40 g/L and resin masses of 0.100 g to 0.800 g. Samples were incubated for 72 hours and styrene oxide production was measured using an HPLC device. Specific loading values reached up to 0.356 g/g for runs without E. coli and nearly 0.003 g of styrene oxide was adsorbed by L-493 during runs with E. coli. Styrene oxide production was most effective at low resin masses and medium glucose concentrations when produced by E. coli.
ContributorsHsu, Joshua (Co-author) / Oremland, Zachary (Co-author) / Nielsen, David (Thesis director) / Staggs, Kyle (Committee member) / Barrett, The Honors College (Contributor) / Chemical Engineering Program (Contributor) / School of Sustainability (Contributor)
Created2014-05
Description
Styrene, a component of many rubber products, is currently synthesized from petroleum in a highly energy-intensive process. The Nielsen Laboratory at Arizona State has demonstrated a biochemical pathway by which E. coli can be engineered to produce styrene from the amino acid phenylalanine, which E. coli naturally synthesizes from glucose.

Styrene, a component of many rubber products, is currently synthesized from petroleum in a highly energy-intensive process. The Nielsen Laboratory at Arizona State has demonstrated a biochemical pathway by which E. coli can be engineered to produce styrene from the amino acid phenylalanine, which E. coli naturally synthesizes from glucose. However, styrene becomes toxic to E. coli above concentrations of 300 mg/L, severely limiting the large-scale applicability of the pathway. Thus, styrene must somehow be continuously removed from the system to facilitate higher yields and for the purposes of scale-up. The separation methods of pervaporation and solvent extraction were investigated to this end. Furthermore, the styrene pathway was extended by one step to produce styrene oxide, which is less volatile than styrene and theoretically simpler to recover. Adsorption of styrene oxide using the hydrophobic resin L-493 was attempted in order to improve the yield of styrene oxide and to provide additional proof of concept that the flux through the styrene pathway can be increased. The maximum styrene titer achieved was 1.2 g/L using the method of solvent extraction, but this yield was only possible when additional phenylalanine was supplemented to the system.
ContributorsMcDaniel, Matthew Cary (Author) / Nielsen, David (Thesis director) / Lind, Mary Laura (Committee member) / McKenna, Rebekah (Committee member) / Barrett, The Honors College (Contributor) / Department of Chemistry and Biochemistry (Contributor) / Chemical Engineering Program (Contributor)
Created2013-05
148174-Thumbnail Image.png
Description

Much of Nepal lacks access to clean drinking water, and many water sources are contaminated with arsenic at concentrations above both World Health Organization and local Nepalese guidelines. While many water treatment technologies exist, it is necessary to identify those that are easily implementable in developing areas. One simple treatment

Much of Nepal lacks access to clean drinking water, and many water sources are contaminated with arsenic at concentrations above both World Health Organization and local Nepalese guidelines. While many water treatment technologies exist, it is necessary to identify those that are easily implementable in developing areas. One simple treatment that has gained popularity is biochar—a porous, carbon-based substance produced through pyrolysis of biomass in an oxygen-free environment. Arizona State University’s Engineering Projects in Community Service (EPICS) has partnered with communities in Nepal in an attempt to increase biochar production in the area, as it has several valuable applications including water treatment. Biochar’s arsenic adsorption capability will be investigated in this project with the goal of using the biochar that Nepalese communities produce to remove water contaminants. It has been found in scientific literature that biochar is effective in removing heavy metal contaminants from water with the addition of iron through surface activation. Thus, the specific goal of this research was to compare the arsenic adsorption disparity between raw biochar and iron-impregnated biochar. It was hypothesized that after numerous bed volumes pass through a water treatment column, iron from the source water will accumulate on the surface of raw biochar, mimicking the intentionally iron-impregnated biochar and further increasing contaminant uptake. It is thus an additional goal of this project to compare biochar loaded with iron through an iron-spiked water column and biochar impregnated with iron through surface oxidation. For this investigation, the biochar was crushed and sieved to a size between 90 and 100 micrometers. Two samples were prepared: raw biochar and oxidized biochar. The oxidized biochar was impregnated with iron through surface oxidation with potassium permanganate and iron loading. Then, X-ray fluorescence was used to compare the composition of the oxidized biochar with its raw counterpart, indicating approximately 0.5% iron in the raw and 1% iron in the oxidized biochar. The biochar samples were then added to batches of arsenic-spiked water at iron to arsenic concentration ratios of 20 mg/L:1 mg/L and 50 mg/L:1 mg/L to determine adsorption efficiency. Inductively coupled plasma mass spectrometry (ICP-MS) analysis indicated an 86% removal of arsenic using a 50:1 ratio of iron to arsenic (1.25 g biochar required in 40 mL solution), and 75% removal with a 20:1 ratio (0.5 g biochar required in 40 mL solution). Additional samples were then inserted into a column process apparatus for further adsorption analysis. Again, ICP-MS analysis was performed and the results showed that while both raw and treated biochars were capable of adsorbing arsenic, they were exhausted after less than 70 bed volumes (234 mL), with raw biochar lasting 60 bed volumes (201 mL) and oxidized about 70 bed volumes (234 mL). Further research should be conducted to investigate more affordable and less laboratory-intensive processes to prepare biochar for water treatment.

ContributorsLaird, Ashlyn (Author) / Schoepf, Jared (Thesis director) / Westerhoff, Paul (Committee member) / Chemical Engineering Program (Contributor) / School of International Letters and Cultures (Contributor) / Barrett, The Honors College (Contributor)
Created2021-05
Description
Ather Arop is bilingual. He is also fluent in Spanish and speaks some French. “Lost Boys Found” is an ongoing, interdisciplinary project that is collecting, recording and archiving the oral histories of the Lost Boys/Girls of Sudan. The collection is a work-in-progress, seeking to record the oral history of as

Ather Arop is bilingual. He is also fluent in Spanish and speaks some French. “Lost Boys Found” is an ongoing, interdisciplinary project that is collecting, recording and archiving the oral histories of the Lost Boys/Girls of Sudan. The collection is a work-in-progress, seeking to record the oral history of as many Lost Boys/Girls as are willing, and will be used in a future book.
ContributorsArop, Ather (Interviewee) / Amparano, Julie (Director) / Garcia, James (Interviewer) / MacNeill, MacNeill (Editor)
Created2017-10-14
Description

Using DFT calculations and GAMESS computational software, porphine and its derivatives were analyzed for unique sites to accept the adsorbates As(III), As(V) and P(V) in order to compare resulting adsorption energies and determine if any of these molecules prefer arsenic oxyanions over phosphate. Pure porphine preferred As(III) over P(V) with

Using DFT calculations and GAMESS computational software, porphine and its derivatives were analyzed for unique sites to accept the adsorbates As(III), As(V) and P(V) in order to compare resulting adsorption energies and determine if any of these molecules prefer arsenic oxyanions over phosphate. Pure porphine preferred As(III) over P(V) with a resulting adsorption energy of -0.7974 eV. Of the functionalized porphyrins tested, carboxyl porphyrin preferred As(V) over P(V) with a total adsorption energy of -0.7345 eV. Ethyl, methyl, chlorine and amino porphyrin all preferred As(III), with energies of -0.7934, -0.8239, -0.7602, and -0.8508 eV, respectively. Of the metalated porphyrins tested, copper and vanadium porphyrin preferred As(V) over P(V) with adsorption energies of -0.7645 and -2.0915 eV. Chromium, iron and magnesium porphyrin all preferred As(III) over P(V) with energies of -0.5993, -1.4539, and - 1.0790 eV, respectively.

ContributorsKusbel, Ashley (Author) / Muhich, Christopher (Thesis director) / Jin, Kailong (Committee member) / Barrett, The Honors College (Contributor) / Chemical Engineering Program (Contributor)
Created2023-05
164187-Thumbnail Image.png
Description

Utilizing DFT calculations, various substitutions on the AlPO-5 zeolite were screened for adsorption of common air molecules. Furthermore, free energy analyses using the Helmholtz free energy equation were performed to determine candidates for selective adsorption of one specific air molecule, and their operating temperature range. Through this study, it was

Utilizing DFT calculations, various substitutions on the AlPO-5 zeolite were screened for adsorption of common air molecules. Furthermore, free energy analyses using the Helmholtz free energy equation were performed to determine candidates for selective adsorption of one specific air molecule, and their operating temperature range. Through this study, it was found that Cerium- (92-542 K), Germanium- (69-370 K), Chromium- (35-293 K), and Praseodymium- (0-420 K) substituted AlPO-5 selectively adsorbs to O2 molecules for the given temperature ranges. In addition, Palladium-substituted AlPO-5 selectively adsorbs to CO within 430-755 K.

ContributorsIrudaya Pious Suresh, Enosh (Author) / Muhich, Christopher (Thesis director) / Emady, Heather (Committee member) / Barrett, The Honors College (Contributor) / Chemical Engineering Program (Contributor)
Created2022-05
165546-Thumbnail Image.png
Description

The outlying cities of Phoenix's West Metropolitan experienced rapid growth in the past ten years. This trend is only going to continue with an average expected growth of 449-891% between 2000 and 2035 (ADOT, 2012). Phoenix is not new to growth and has consistently seen swaths of people added to

The outlying cities of Phoenix's West Metropolitan experienced rapid growth in the past ten years. This trend is only going to continue with an average expected growth of 449-891% between 2000 and 2035 (ADOT, 2012). Phoenix is not new to growth and has consistently seen swaths of people added to its population. This raises the question of what happened to the people who lived in Phoenix's West Valley during this period of rapid change and growth in their communities? What are their stories and what do their stories reveal about the broader public history of change in Phoenix's West Valley? In consideration of these questions, the community oral histories of eight residents from the West Valley were collected to add historical nuance to the limited archival records available in the area. From this collection, the previous notion of "post-war boomtowns” describing Phoenix’s West Valley was revealed to be highly inaccurate and dismissive of the residents' experiences who lived and formed their lives there.

ContributorsGeiser, Samantha (Author) / Campanile, Isabella (Co-author) / Martinez Orozco, Rafael (Thesis director) / O'Flaherty, Katherine (Committee member) / Barrett, The Honors College (Contributor) / Chemical Engineering Program (Contributor) / School of Mathematical and Statistical Sciences (Contributor)
Created2022-05