Matching Items (134)
Filtering by
- All Subjects: Electrical Engineering
- Creators: Bakkaloglu, Bertan
- Resource Type: Text
- Status: Published
Description
Power management integrated circuit (PMIC) design is a key module in almost all electronics around us such as Phones, Tablets, Computers, Laptop, Electric vehicles, etc. The on-chip loads such as microprocessors cores, memories, Analog/RF, etc. requires multiple supply voltage domains. Providing these supply voltages from off-chip voltage regulators will increase the overall system cost and limits the performance due to the board and package parasitics. Therefore, an on-chip fully integrated voltage regulator (FIVR) is required.
The dissertation presents a topology for a fully integrated power stage in a DC-DC buck converter achieving a high-power density and a time-domain hysteresis based highly integrated buck converter. A multi-phase time-domain comparator is proposed in this work for implementing the hysteresis control, thereby achieving a process scaling friendly highly digital design. A higher-order LC notch filter along with a flying capacitor which couples the input and output voltage ripple is implemented. The power stage operates at 500 MHz and can deliver a maximum power of 1.0 W and load current of 1.67 A, while occupying 1.21 mm2 active die area. Thus achieving a power density of 0.867 W/mm2 and current density of 1.377 A/mm2. The peak efficiency obtained is 71% at 780 mA of load current. The power stage with the additional off-chip LC is utilized to design a highly integrated current mode hysteretic buck converter operating at 180 MHz. It achieves 20 ns of settling and 2-5 ns of rise/fall time for reference tracking.
The second part of the dissertation discusses an integrated low voltage switched-capacitor based power sensor, to measure the output power of a DC-DC boost converter. This approach results in a lower complexity, area, power consumption, and a lower component count for the overall PV MPPT system. Designed in a 180 nm CMOS process, the circuit can operate with a supply voltage of 1.8 V. It achieves a power sense accuracy of 7.6%, occupies a die area of 0.0519 mm2, and consumes 0.748 mW of power.
The dissertation presents a topology for a fully integrated power stage in a DC-DC buck converter achieving a high-power density and a time-domain hysteresis based highly integrated buck converter. A multi-phase time-domain comparator is proposed in this work for implementing the hysteresis control, thereby achieving a process scaling friendly highly digital design. A higher-order LC notch filter along with a flying capacitor which couples the input and output voltage ripple is implemented. The power stage operates at 500 MHz and can deliver a maximum power of 1.0 W and load current of 1.67 A, while occupying 1.21 mm2 active die area. Thus achieving a power density of 0.867 W/mm2 and current density of 1.377 A/mm2. The peak efficiency obtained is 71% at 780 mA of load current. The power stage with the additional off-chip LC is utilized to design a highly integrated current mode hysteretic buck converter operating at 180 MHz. It achieves 20 ns of settling and 2-5 ns of rise/fall time for reference tracking.
The second part of the dissertation discusses an integrated low voltage switched-capacitor based power sensor, to measure the output power of a DC-DC boost converter. This approach results in a lower complexity, area, power consumption, and a lower component count for the overall PV MPPT system. Designed in a 180 nm CMOS process, the circuit can operate with a supply voltage of 1.8 V. It achieves a power sense accuracy of 7.6%, occupies a die area of 0.0519 mm2, and consumes 0.748 mW of power.
ContributorsSingh, Shrikant (Author) / Kiaei, Sayfe (Thesis advisor) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Song, Hongjiang (Committee member) / Arizona State University (Publisher)
Created2019
Description
State-of-the-art automotive radars use multi-chip Frequency Modulated Continuous Wave (FMCW) radars to sense the environment around the car. FMCW radars are prone to interference as they operate over a narrow baseband bandwidth and use similar radio frequency (RF) chirps among them. Phase Modulated Continuous Wave radars (PMCW) are robust and insensitive to interference as they transmit signals over a wider bandwidth using spread spectrum technique. As more and more cars are equipped with FMCW radars illuminate the same environment, interference would soon become a serious issue. PMCW radars can be an effective solution to interference in the noisy FMCW radar environment. PMCW radars can be implemented in silicon as System-on-a-chip (SoC), suitable for Multiple-Input-Multiple-Output (MIMO) implementation and is highly programmable. PMCW radars do not require highly linear high frequency chirping oscillators thus reducing the size of the final solution.
This thesis aims to present a behavior model for this promising Digitally modulated radar (DMR) transceiver in Simulink/Matlab. The goal of this work is to create a model for the electronic system level framework that simulates the entire system with non-idealities. This model includes a Top Down Design methodology to understand the requirements of the individual modules’ performance and thus derive the specifications for implementing the real chip. Back annotation of the actual electrical modules’ performance to the model closes the design process loop. Using Simulink’s toolboxes, a passband and equivalent baseband model of the system is built for the transceiver with non-idealities of the components built in along with signal processing routines in Matlab. This model provides a platform for system evaluation and simulation for various system scenarios and use-cases of sensing using the environment around a moving car.
This thesis aims to present a behavior model for this promising Digitally modulated radar (DMR) transceiver in Simulink/Matlab. The goal of this work is to create a model for the electronic system level framework that simulates the entire system with non-idealities. This model includes a Top Down Design methodology to understand the requirements of the individual modules’ performance and thus derive the specifications for implementing the real chip. Back annotation of the actual electrical modules’ performance to the model closes the design process loop. Using Simulink’s toolboxes, a passband and equivalent baseband model of the system is built for the transceiver with non-idealities of the components built in along with signal processing routines in Matlab. This model provides a platform for system evaluation and simulation for various system scenarios and use-cases of sensing using the environment around a moving car.
ContributorsKalyan, Prassana (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Thesis advisor) / Garrity, Douglas (Committee member) / Arizona State University (Publisher)
Created2019
Description
This dissertation focuses on three different efficiency enhancement methods that are applicable to handset applications. These proposed designs are based on three critical requirements for handset application: 1) Small form factor, 2) CMOS compatibility and 3) high power handling. The three presented methodologies are listed below:
1) A transformer-based power combiner architecture for out-phasing transmitters
2) A current steering DAC-based average power tracking circuit for on-chip power amplifiers (PA)
3) A CMOS-based driver stage for GaN-based switched-mode power amplifiers applicable to fully digital transmitters
This thesis highlights the trends in wireless handsets, the motivates the need for fully-integrated CMOS power amplifier solutions and presents the three novel techniques for reconfigurable and digital CMOS-based PAs. Chapter 3, presents the transformer-based power combiner for out-phasing transmitters. The simulation results reveal that this technique is able to shrink the power combiner area, which is one of the largest parts of the transmitter, by about 50% and as a result, enhances the output power density by 3dB.
The average power tracking technique (APT) integrated with an on-chip CMOS-based power amplifier is explained in Chapter 4. This system is able to achieve up to 32dBm saturated output power with a linear power gain of 20dB in a 45nm CMOS SOI process. The maximum efficiency improvement is about ∆η=15% compared to the same PA without APT. Measurement results show that the proposed method is able to amplify an enhanced-EDGE modulated input signal with a data rate of 70.83kb/sec and generate more than 27dBm of average output power with EVM<5%.
Although small form factor, high battery lifetime, and high volume integration motivate the need for fully digital CMOS transmitters, the output power generated by this type of transmitter is not high enough to satisfy the communication standards. As a result, compound materials such as GaN or GaAs are usually being used in handset applications to increase the output power. Chapter 5 focuses on the analysis and design of two CMOS based driver architectures (cascode and house of cards) for driving a GaN power amplifier. The presented results show that the drivers are able to generate ∆Vout=5V, which is required by the compound transistor, and operate up to 2GHz. Since the CMOS driver is expected to drive an off-chip capacitive load, the interface components, such as bond wires, and decoupling and pad capacitors, play a critical role in the output transient response. Therefore, extensive analysis and simulation results have been done on the interface circuits to investigate their effects on RF transmitter performance. The presented results show that the maximum operating frequency when the driver is connected to a 4pF capacitive load is about 2GHz, which is perfectly matched with the reported values in prior literature.
1) A transformer-based power combiner architecture for out-phasing transmitters
2) A current steering DAC-based average power tracking circuit for on-chip power amplifiers (PA)
3) A CMOS-based driver stage for GaN-based switched-mode power amplifiers applicable to fully digital transmitters
This thesis highlights the trends in wireless handsets, the motivates the need for fully-integrated CMOS power amplifier solutions and presents the three novel techniques for reconfigurable and digital CMOS-based PAs. Chapter 3, presents the transformer-based power combiner for out-phasing transmitters. The simulation results reveal that this technique is able to shrink the power combiner area, which is one of the largest parts of the transmitter, by about 50% and as a result, enhances the output power density by 3dB.
The average power tracking technique (APT) integrated with an on-chip CMOS-based power amplifier is explained in Chapter 4. This system is able to achieve up to 32dBm saturated output power with a linear power gain of 20dB in a 45nm CMOS SOI process. The maximum efficiency improvement is about ∆η=15% compared to the same PA without APT. Measurement results show that the proposed method is able to amplify an enhanced-EDGE modulated input signal with a data rate of 70.83kb/sec and generate more than 27dBm of average output power with EVM<5%.
Although small form factor, high battery lifetime, and high volume integration motivate the need for fully digital CMOS transmitters, the output power generated by this type of transmitter is not high enough to satisfy the communication standards. As a result, compound materials such as GaN or GaAs are usually being used in handset applications to increase the output power. Chapter 5 focuses on the analysis and design of two CMOS based driver architectures (cascode and house of cards) for driving a GaN power amplifier. The presented results show that the drivers are able to generate ∆Vout=5V, which is required by the compound transistor, and operate up to 2GHz. Since the CMOS driver is expected to drive an off-chip capacitive load, the interface components, such as bond wires, and decoupling and pad capacitors, play a critical role in the output transient response. Therefore, extensive analysis and simulation results have been done on the interface circuits to investigate their effects on RF transmitter performance. The presented results show that the maximum operating frequency when the driver is connected to a 4pF capacitive load is about 2GHz, which is perfectly matched with the reported values in prior literature.
ContributorsMoallemi, Soroush (Author) / Kitchen, Jennifer (Thesis advisor) / Kiaei, Sayfe (Committee member) / Bakkaloglu, Bertan (Committee member) / Thornton, Trevor (Committee member) / Arizona State University (Publisher)
Created2019
Description
The efficiency of spacecraft’s solar cells reduces over the course of their operation. Traditionally, they are configured to extract maximum power at the end of their life and not have a system which dynamically extracts the maximum power over their entire life. This work demonstrates the benefit of dynamic re-configuration of spacecraft’s solar arrays to access the full power available from the solar panels throughout their lifetime. This dynamic re-configuration is achieved using enhancement mode GaN devices as the switches due to their low Ron and small footprint.
This work discusses hardware Implementation challenges and a prototype board is designed using components-off-the-shelf (COTS) to study the behavior of photovoltaic (PV) panels with different configurations of switches between 5 PV cells. The measurement results from the board proves the feasibility of the idea, showing the power improvements of having the switch structure. The measurement results are used to simulate a 1kW satellite system and understand practical trade-offs of this idea in actual satellite power systems.
Additionally, this work also presents the implementation of CMOS controller integrated circuit (IC) in 0.18um technology. The CMOS controller IC includes switched-capacitor converters in open loop to provide the floating voltages required to drive the GaN switches. Each CMOS controller IC can drive 10 switches in series and parallel combination. Furthermore, the designed controller IC is expected to operate under 300MRad of total dose radiation, thus enabling the controller modules to be placed on the solar cell wings of the satellites.
This work discusses hardware Implementation challenges and a prototype board is designed using components-off-the-shelf (COTS) to study the behavior of photovoltaic (PV) panels with different configurations of switches between 5 PV cells. The measurement results from the board proves the feasibility of the idea, showing the power improvements of having the switch structure. The measurement results are used to simulate a 1kW satellite system and understand practical trade-offs of this idea in actual satellite power systems.
Additionally, this work also presents the implementation of CMOS controller integrated circuit (IC) in 0.18um technology. The CMOS controller IC includes switched-capacitor converters in open loop to provide the floating voltages required to drive the GaN switches. Each CMOS controller IC can drive 10 switches in series and parallel combination. Furthermore, the designed controller IC is expected to operate under 300MRad of total dose radiation, thus enabling the controller modules to be placed on the solar cell wings of the satellites.
ContributorsHeblikar, Anand N (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2019
Description
Point of Load (POL) DC-DC converters are increasingly used in space applications, data centres, electric vehicles, portable computers and devices and medical electronics. Heavy computing and processing capabilities of the modern devices have ushered the use of higher battery supply voltage to increase power storage. The need to address this consumer experience driven requirement has propelled the evolution of the next generation of small form-factor power converters which can operate with higher step down ratios while supplying heavy continuous load currents without sacrificing efficiency. Constant On-Time (COT) converter topology is capable of achieving stable operation at high conversion ratio with minimum off-chip components and small silicon area. This work proposes a Constant On-Time buck dc-dc converter for a wide dynamic input range and load currents from 100mA to 10A. Accuracy of this ripple based converter is improved by a unique voltage positioning technique which modulates the reference voltage to lower the average ripple profile close to the nominal output. Adaptive On-time block features a transient enhancement scheme to assist in faster voltage droop recovery when the output voltage dips below a defined threshold. UtilizingGallium Nitride (GaN) power switches enable the proposed converter to achieve very high efficiency while using smaller size inductor-capacitor (LC) power-stage. Use of novel Superjunction devices with higher drain-source blocking voltage simplifies the complex driver design and enables faster frequency of operation. It allows 1.8VComplementary Metal-Oxide Semiconductor (CMOS) devices to effectively drive GaNpower FETs which require 5V gate signal swing. The presented controller circuit uses internal ripple generation which reduces reliance on output cap equivalent series resistance (ESR) for loop stability and facilitates ripples reduction at the output. The ripple generation network is designed to provide ai
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
optimally stable performance while maintaining load regulation and line regulation accuracy withing specified margin. The chip with ts external Power FET package is proposed to be integrated on a printed circuit board for testing. The designed power converter is expected to operate under 200 MRad of a total ionising dose of radiation enabling it to function within large hadron collider at CERN and space satellite and probe missions.
ContributorsJoshi, Omkar (Author) / Bakkaloglu, Bertan (Thesis advisor) / Kitchen, Jennifer (Committee member) / Long, Yu (Committee member) / Arizona State University (Publisher)
Created2019
Description
Respiratory behavior provides effective information to characterize lung functionality, including respiratory rate, respiratory profile, and respiratory volume. Current methods have limited capabilities of continuous characterization of respiratory behavior and are primarily targeting the measurement of respiratory rate, which has relatively less value in clinical application. In this dissertation, a wireless wearable sensor on a paper substrate is developed to continuously characterize respiratory behavior and deliver clinically relevant parameters, contributing to asthma control. Based on the anatomical analysis and experimental results, the optimum site for the wireless wearable sensor is on the midway of the xiphoid process and the costal margin, corresponding to the abdomen-apposed rib cage. At the wearing site, the linear strain change during respiration is measured and converted to lung volume by the wireless wearable sensor utilizing a distance-elapsed ultrasound. An on-board low-power Bluetooth module transmits the temporal lung volume change to a smartphone, where a custom-programmed app computes to show the clinically relevant parameters, such as forced vital capacity (FVC) and forced expiratory volume delivered in the first second (FEV1) and the FEV1/FVC ratio. Enhanced by a simple, yet effective machine-learning algorithm, a system consisting of two wireless wearable sensors accurately extracts respiratory features and classifies the respiratory behavior within four postures among different subjects, demonstrating that the respiratory behaviors are individual- and posture-dependent contributing to monitoring the posture-related respiratory diseases. The continuous and accurate monitoring of respiratory behaviors can track the respiratory disorders and diseases' progression for timely and objective approaches for control and management.
ContributorsChen, Ang (Author) / Cao, Yu (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Allee, David (Committee member) / Goryll, Michael (Committee member) / Arizona State University (Publisher)
Created2020
Description
This work analyzes and develops a point-of-load (PoL) synchronous buck converter using enhancement-mode Gallium Nitride (e-GaN), with emphasis on optimizing reverse conduction loss by using a well-known technique of placing an anti-parallel Schottky diode across the synchronous power device. This work develops an improved analytical switching model for the GaN-based converter with the Schottky diode using piecewise linear approximations.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
To avoid a shoot-through between the power switches of the buck converter, a small dead-time is inserted between gate drive switching transitions. Despite optimum dead-time management for a power converter, optimum dead-times vary for different load conditions. These variations become considerably large for PoL applications, which demand high output current with low output voltages. At high switching frequencies, these variations translate into losses that contribute significantly to the total loss of the converter. To understand and quantify power loss in a hard-switching buck converter that uses a GaN power device in parallel with a Schottky diode, piecewise transitions are used to develop an analytical switching model that quantifies the contribution of reverse conduction loss of GaN during dead-time.
The effects of parasitic elements on the dynamics of the switching converter are investigated during one switching cycle of the converter. A designed prototype of a buck converter is correlated to the predicted model to determine the accuracy of the model. This comparison is presented using simulations and measurements at 400 kHz and 2 MHz converter switching speeds for load (1A) condition and fixed dead-time values. Furthermore, performance of the buck converter with and without the Schottky diode is also measured and compared to demonstrate and quantify the enhanced performance when using an anti-parallel diode. The developed power converter achieves peak efficiencies of 91.7% and 93.86% for 2 MHz and 400 KHz switching frequencies, respectively, and drives load currents up to 6A for a voltage conversion from 12V input to 3.3V output.
In addition, various industry Schottky diodes have been categorized based on their packaging and electrical characteristics and the developed analytical model provides analytical expressions relating the diode characteristics to power stage performance parameters. The performance of these diodes has been characterized for different buck converter voltage step-down ratios that are typically used in industry applications and different switching frequencies ranging from 400 KHz to 2 MHz.
ContributorsKoli, Gauri (Author) / Kitchen, Jennifer (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ozev, Sule (Committee member) / Arizona State University (Publisher)
Created2020
Description
Power management circuits have been more and more widely used in various applications, while providing fully integrated voltage regulation remains a challenging topic. Switched-capacitor (SC) voltage converters have received attentions in integrated power conversion for fixed-ratio voltage conversions with good efficiency and feasibility of integration. During my PhD study, an on-chip current sensing technique is proposed to dynamically modulate both switching frequency and switch widths of SC voltage converters, enhancing fast transient response and higher efficiency across a wide range of load currents. In conjunction with SC converters, a low-dropout regulator (LDO) is implemented which is driven by a push-pull operational transconductance amplifier (OTA), whose current is mirrored and sensed with minimal power and efficiency overhead. The sensed load current directly controls the frequency and width of SC converters through a voltage-controlled oscillator (VCO) and a time-to-digital converter, respectively.
Theoretical analysis and optimization for SC DC-DC converters have been presented in prior works, however optimization of different capacitors, namely flying and input/output decoupling capacitors, in SC voltage regulators (SCVRs) under an area constraint has not been addressed. A methodology to optimize flying and decoupling capacitance for area-constrained on-chip SCVRs to achieve the highest system-level power efficiency. Considering both conversion efficiency and droop voltage against fast load transients, the proposed model determines the optimal ratio between flying and decoupling.
Based on the previous design, a fully integrated switched-capacitor voltage regulator with voltage comparison and on-chip lossless current sensing control is proposed. Based on the voltage comparison result and sensed current as the load current changes, the frequency of the SC converters are modulated for optimal efficiency. The voltage regulator targets 2.1V input voltage and 0.9V output voltage, which offers higher-voltage power transfer across chip package. A 17-phase interleaved structure is used to reduce output voltage ripple.
In 65nm CMOS, the regulator is implemented with MIM-capacitor, targeting 2.1V input voltage and 0.9V output voltage. According to the measurement results, the proposed SC voltage regulator achieves 69.6% peak efficiency at 60mA load current, which corresponds to a 4.2mW/mm2 power-area density and 12.5mW
F power-capacitance density. The efficiency across 20mA to 92mA regulator load current range is above 62%. The steady-state output voltage ripple across 22x load current range of 3.5mA-76mA is between 50mV to 60mV.
Theoretical analysis and optimization for SC DC-DC converters have been presented in prior works, however optimization of different capacitors, namely flying and input/output decoupling capacitors, in SC voltage regulators (SCVRs) under an area constraint has not been addressed. A methodology to optimize flying and decoupling capacitance for area-constrained on-chip SCVRs to achieve the highest system-level power efficiency. Considering both conversion efficiency and droop voltage against fast load transients, the proposed model determines the optimal ratio between flying and decoupling.
Based on the previous design, a fully integrated switched-capacitor voltage regulator with voltage comparison and on-chip lossless current sensing control is proposed. Based on the voltage comparison result and sensed current as the load current changes, the frequency of the SC converters are modulated for optimal efficiency. The voltage regulator targets 2.1V input voltage and 0.9V output voltage, which offers higher-voltage power transfer across chip package. A 17-phase interleaved structure is used to reduce output voltage ripple.
In 65nm CMOS, the regulator is implemented with MIM-capacitor, targeting 2.1V input voltage and 0.9V output voltage. According to the measurement results, the proposed SC voltage regulator achieves 69.6% peak efficiency at 60mA load current, which corresponds to a 4.2mW/mm2 power-area density and 12.5mW
F power-capacitance density. The efficiency across 20mA to 92mA regulator load current range is above 62%. The steady-state output voltage ripple across 22x load current range of 3.5mA-76mA is between 50mV to 60mV.
ContributorsMi, Xiaoyang (Author) / Seo, Jae-Sun (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Ogras, Umit Y. (Committee member) / Kitchen, Jennifer (Committee member) / Arizona State University (Publisher)
Created2020
Description
Nearly all solar photovoltaic (PV) systems are designed with maximum power point tracking (MPPT) functionality to maximize the utilization of available power from the PV array throughout the day. In conventional PV systems, the MPPT function is handled by a power electronic device, like a DC-AC inverter. However, given that most PV systems are designed to be grid-connected, there are several challenges for designing PV systems for DC-powered applications and off-grid applications. The first challenge is that all power electronic devices introduce some degree of power loss. Beyond the cost of the lost power, the upfront cost of power electronics also increases with the required power rating. Second, there are very few commercially available options for DC-DC converters that include MPPT functionality, and nearly all PV inverters are designed as “grid-following” devices, as opposed to “grid-forming” devices, meaning they cannot be used in off-grid applications.
To address the challenges of designing PV systems for high-power DC and off-grid applications, a load-managing photovoltaic (LMPV) system topology has been proposed. Instead of using power electronics, the LMPV system performs maximum power point tracking through load management. By implementing a load-management approach, the upfront costs and the power losses associated with the power electronics are avoided, both of which improve the economic viability of the PV system. This work introduces the concept of an LMPV system, provides in-depth analyses through both simulation and experimental validation, and explores several potential applications of the system, such as solar-powered commercial-scale electrolyzers for the production of hydrogen fuel or the production and purification of raw materials like caustic soda, copper, and zinc.
To address the challenges of designing PV systems for high-power DC and off-grid applications, a load-managing photovoltaic (LMPV) system topology has been proposed. Instead of using power electronics, the LMPV system performs maximum power point tracking through load management. By implementing a load-management approach, the upfront costs and the power losses associated with the power electronics are avoided, both of which improve the economic viability of the PV system. This work introduces the concept of an LMPV system, provides in-depth analyses through both simulation and experimental validation, and explores several potential applications of the system, such as solar-powered commercial-scale electrolyzers for the production of hydrogen fuel or the production and purification of raw materials like caustic soda, copper, and zinc.
ContributorsAzzolini, Joseph Anthony (Author) / Tao, Meng (Thesis advisor) / Bakkaloglu, Bertan (Committee member) / Qin, Jiangchao (Committee member) / Reno, Matthew J. (Committee member) / Arizona State University (Publisher)
Created2020
Description
Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.
ContributorsGrout, Kevin Samuel (Author) / Kitchen, Jennifer N (Thesis advisor) / Khalil, Waleed (Committee member) / Bakkaloglu, Bertan (Committee member) / Aberle, James T., 1961- (Committee member) / Garrity, Douglas (Committee member) / Arizona State University (Publisher)
Created2019