Matching Items (5)
Filtering by
- All Subjects: Electrical Engineering
Description
The purpose of this dissertation is to develop a design technique for fractional PID controllers to achieve a closed loop sensitivity bandwidth approximately equal to a desired bandwidth using frequency loop shaping techniques. This dissertation analyzes the effect of the order of a fractional integrator which is used as a target on loop shaping, on stability and performance robustness. A comparison between classical PID controllers and fractional PID controllers is presented. Case studies where fractional PID controllers have an advantage over classical PID controllers are discussed. A frequency-domain loop shaping algorithm is developed, extending past results from classical PID’s that have been successful in tuning controllers for a variety of practical systems.
ContributorsSaleh, Khalid M (Author) / Tsakalis, Konstantinos (Thesis advisor) / Rodriguez, Armando (Committee member) / Si, Jennie (Committee member) / Artemiadis, Panagiotis (Committee member) / Arizona State University (Publisher)
Created2017
Description
Many industries require workers in warehouse and stockroom environments to perform frequent lifting tasks. Over time these repeated tasks can lead to excess strain on the worker's body and reduced productivity. This project seeks to develop an exoskeletal wrist fixture to be used in conjunction with a powered exoskeleton arm to aid workers performing box lifting types of tasks. Existing products aimed at improving worker comfort and productivity typically employ either fully powered exoskeleton suits or utilize minimally powered spring arms and/or fixtures. These designs either reduce stress to the user's body through powered arms and grippers operated via handheld controls which have limited functionality, or they use a more minimal setup that reduces some load, but exposes the user's hands and wrists to injury by directing support to the forearm. The design proposed here seeks to strike a balance between size, weight, and power requirements and also proposes a novel wrist exoskeleton design which minimizes stress on the user's wrists by directly interfacing with the object to be picked up. The design of the wrist exoskeleton was approached through initially selecting degrees of freedom and a ROM (range of motion) to accommodate. Feel and functionality were improved through an iterative prototyping process which yielded two primary designs. A novel "clip-in" method was proposed to allow the user to easily attach and detach from the exoskeleton. Designs utilized a contact surface intended to be used with dry fibrillary adhesives to maximize exoskeleton grip. Two final designs, which used two pivots in opposite kinematic order, were constructed and tested to determine the best kinematic layout. The best design had two prototypes created to be worn with passive test arms that attached to the user though a specially designed belt.
ContributorsGreason, Kenneth Berend (Author) / Sugar, Thomas (Thesis director) / Holgate, Matthew (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-12
Description
For the past two decades, advanced Limb Gait Simulators and Exoskeletons have been developed to improve walking rehabilitation. A Limb Gait Simulator is used to analyze the human step cycle and/or assist a user walking on a treadmill. Most modern limb gait simulators, such as ALEX, have proven themselves effective and reliable through their usage of motors, springs, cables, elastics, pneumatics and reaction loads. These mechanisms apply internal forces and reaction loads to the body. On the other hand, external forces are those caused by an external agent outside the system such as air, water, or magnets. A design for an exoskeleton using external forces has seldom been attempted by researchers. This thesis project focuses on the development of a Limb Gait Simulator based on a Pure External Force and has proven its effectiveness in generating torque on the human leg. The external force is generated through air propulsion using an Electric Ducted Fan (EDF) motor. Such a motor is typically used for remote control airplanes, but their applications can go beyond this. The objective of this research is to generate torque on the human leg through the control of the EDF engines thrust and the opening/closing of the reverse thruster flaps. This device qualifies as "assist as needed"; the user is entirely in control of how much assistance he or she may want. Static thrust values for the EDF engine are recorded using a thrust test stand. The product of the thrust (N) and the distance on the thigh (m) is the resulting torque. With the motor running at maximum RPM, the highest torque value reached was that of 3.93 (Nm). The motor EDF motor is powered by a 6S 5000 mAh LiPo battery. This torque value could be increased with the usage of a second battery connected in series, but this comes at a price. The designed limb gait simulator demonstrates that external forces, such as air, could have potential in the development of future rehabilitation devices.
ContributorsToulouse, Tanguy Nathan (Author) / Sugar, Thomas (Thesis director) / Artemiadis, Panagiotis (Committee member) / Mechanical and Aerospace Engineering Program (Contributor) / Barrett, The Honors College (Contributor)
Created2016-12
Description
To achieve the ambitious long-term goal of a feet of cooperating Flexible Autonomous
Machines operating in an uncertain Environment (FAME), this thesis addresses several
critical modeling, design, control objectives for rear-wheel drive ground vehicles.
Toward this ambitious goal, several critical objectives are addressed. One central objective of the thesis was to show how to build low-cost multi-capability robot platform
that can be used for conducting FAME research.
A TFC-KIT car chassis was augmented to provide a suite of substantive capabilities.
The augmented vehicle (FreeSLAM Robot) costs less than $500 but offers the capability
of commercially available vehicles costing over $2000.
All demonstrations presented involve rear-wheel drive FreeSLAM robot. The following
summarizes the key hardware demonstrations presented and analyzed:
(1)Cruise (v, ) control along a line,
(2) Cruise (v, ) control along a curve,
(3) Planar (x, y) Cartesian Stabilization for rear wheel drive vehicle,
(4) Finish the track with camera pan tilt structure in minimum time,
(5) Finish the track without camera pan tilt structure in minimum time,
(6) Vision based tracking performance with different cruise speed vx,
(7) Vision based tracking performance with different camera fixed look-ahead distance L,
(8) Vision based tracking performance with different delay Td from vision subsystem,
(9) Manually remote controlled robot to perform indoor SLAM,
(10) Autonomously line guided robot to perform indoor SLAM.
For most cases, hardware data is compared with, and corroborated by, model based
simulation data. In short, the thesis uses low-cost self-designed rear-wheel
drive robot to demonstrate many capabilities that are critical in order to reach the
longer-term FAME goal.
Machines operating in an uncertain Environment (FAME), this thesis addresses several
critical modeling, design, control objectives for rear-wheel drive ground vehicles.
Toward this ambitious goal, several critical objectives are addressed. One central objective of the thesis was to show how to build low-cost multi-capability robot platform
that can be used for conducting FAME research.
A TFC-KIT car chassis was augmented to provide a suite of substantive capabilities.
The augmented vehicle (FreeSLAM Robot) costs less than $500 but offers the capability
of commercially available vehicles costing over $2000.
All demonstrations presented involve rear-wheel drive FreeSLAM robot. The following
summarizes the key hardware demonstrations presented and analyzed:
(1)Cruise (v, ) control along a line,
(2) Cruise (v, ) control along a curve,
(3) Planar (x, y) Cartesian Stabilization for rear wheel drive vehicle,
(4) Finish the track with camera pan tilt structure in minimum time,
(5) Finish the track without camera pan tilt structure in minimum time,
(6) Vision based tracking performance with different cruise speed vx,
(7) Vision based tracking performance with different camera fixed look-ahead distance L,
(8) Vision based tracking performance with different delay Td from vision subsystem,
(9) Manually remote controlled robot to perform indoor SLAM,
(10) Autonomously line guided robot to perform indoor SLAM.
For most cases, hardware data is compared with, and corroborated by, model based
simulation data. In short, the thesis uses low-cost self-designed rear-wheel
drive robot to demonstrate many capabilities that are critical in order to reach the
longer-term FAME goal.
ContributorsLu, Xianglong (Author) / Rodriguez, Armando Antonio (Thesis advisor) / Berman, Spring (Committee member) / Artemiadis, Panagiotis (Committee member) / Arizona State University (Publisher)
Created2016
Description
With recent advances in missile and hypersonic vehicle technologies, the need for being able to accurately simulate missile-target engagements has never been greater. Within this research, we examine a fully integrated missile-target engagement environment. A MATLAB based application is developed with 3D animation capabilities to study missile-target engagement and visualize them. The high fidelity environment is used to validate miss distance analysis with the results presented in relevant GNC textbooks and to examine how the kill zone varies with critical engagement parameters; e.g. initial engagement altitude, missile Mach, and missile maximum acceleration. A ray-based binary search algorithm is used to estimate the kill zone region; i.e. the set of initial target starting conditions such that it will be "killed". The results show what is expected. The kill zone increases with larger initial missile Mach and maximum acceleration & decreases with higher engagement altitude and higher target Mach. The environment is based on (1) a 6DOF bank-to-turn (BTT) missile, (2) a full aerodynamic-stability derivative look up tables ranging over Mach number, angle of attack and sideslip angle (3) a standard atmosphere model, (4) actuator dynamics for each of the four cruciform fins, (5) seeker dynamics, (6) a nonlinear autopilot, (7) a guidance system with three guidance algorithms (i.e. PNG, optimal, differential game theory), (8) a 3DOF target model with three maneuverability models (i.e. constant speed, Shelton Turn & Climb, Riggs-Vergaz Turn & Dive). Each of the subsystems are described within the research. The environment contains linearization, model analysis and control design features. A gain scheduled nonlinear BTT missile autopilot is presented here. Autopilot got sluggish as missile altitude increased and got aggressive as missile mach increased. In short, the environment is shown to be a very powerful tool for conducting missile-target engagement research - a research that could address multiple missiles and advanced targets.
ContributorsRenganathan, Venkatraman (Author) / Rodriguez, Armando A (Thesis advisor) / Artemiadis, Panagiotis (Committee member) / Berman, Spring M (Committee member) / Arizona State University (Publisher)
Created2016